Desa VP1600C, VP2600C Thermostat Sensing Bulb, Models VP1600IT and VP2200IT Only

Page 10

10

INSTALLING TO WALL

Continued

For convenience and efficiency, install heater

•where there is easy access for operation, inspection, and service

•in coldest part of room

An optional fan kit is available from your dealer. See Accessories, page 31 If planning to use fan, locate heater near an electrical outlet.

CEILING

	36"
8"	Minimum
8"
Minimum
From
Sides Of
Heater
Left	Right
Side	Side

	3" Minimum To Top Surface
FLOOR	Of Carpeting, Tile Or Other
FLOOR	Combustible Material

Figure 4 - Mounting Clearances As Viewed From Front of Heater

THERMOSTAT SENSING BULB

(Models VP1600IT and VP2200IT Only)

The thermostat sensing bulb has been placed inside the heater for protection during shipping.

Locating Thermostat Sensing Bulb

1.Remove front panel of heater (see Figure 7, page 11).

2.Locate thermostat sensing bulb just under burner assembly.

IMPORTANT: Attach thermostat sensing bulb to back of heater for proper operation.

Attaching Thermostat Sensing Bulb

1.Remove thermostat sensing bulb from holders inside heater. Route through slot opening in bottom of heater.

2.Place clamp on thermostat sensing bulb as shown in Figure 5. Clamp is provided in hardware package.

3.Snap clamp into upper mounting hole as shown in Figure 5. Mounting hole is located on lower left edge on back of heater. Make sure the thermostat sensing bulb is pointing up.

Thermostat

Sensing Bulb

Clamp

Figure 5 - Attaching Thermostat Sensing Bulb

100751

Image 10

Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASContents Safety InformationSafety Information Local Codes FeaturesIdentification UnpackingVentilation Fresh AIR ForCombustion Producing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Fresh AIRDetermining if You Have a Confined or Unconfined Space Ventilation AIR Fresh AIR for Combustion and VentilationVentilation Air From Inside Building Ventilation AIR Ventilation Air From OutdoorsCheck GAS Type Installing To WallInstallation Items Locating HeaterLocating Thermostat Sensing Bulb Thermostat Sensing BulbModels VP1600IT and VP2200IT Only Attaching Thermostat Sensing BulbRemoving Front Panel Of Heater Installing Heater to WallMounting Bracket Methods For Attaching Mounting Bracket To WallMarking Screw Locations Attaching Mounting Bracket To WallInstalling Bottom Mounting Screws Placing Heater On Mounting BracketSupply Connecting To GASQualified service person must connect heater to gas supply Follow all local codesConnections Pressure Testing GAS Supply Piping SystemChecking GAS Servicing. Correct all leaks at onceConnecting Pressure Testing Heater GAS ConnectionsOperating Heater Operating Heater Lighting InstructionsHeater To Select Heating LevelShutting Off Heater Shutting Off Burner Only pilot stays litOperating If you do not follow these instructions exactly, a fire orModels VP1600C and VP2600C LOW MED High Inspecting Burner Pilot Flame PatternBurner Flame Pattern Trouble Shooting CleaningMaintenance ODS/PILOT and Burner OrificeCleaning and Mainte TroubleSee Cleaning TROUBLE- ShootingIf you smell gas ServiceTechnical Shut off gas supplyVP1600IT VP2200IT Service Publications HintsVP1600C VP2600C Replacement Parts AccessoriesIllustrated Parts Breakdown Model VP1600ITParts List KEY Part Number Description QTYModel VP2200IT Parts List Model VP1600C Control Position Label Model VP2600C Parts List Warranty Information Keep this Warranty