Genie 2022, 2042, 2024 manual Rail Assembly for Chain Drive Opener

Page 10

Rail Assembly for CHAIN DRIVE OPENER

NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1.

3.Remove the two rail sections that are not connected to the chain and place them on floor (Fig. 1-2, A).

4.Carefully remove the third rail section with chain and plastic sleeve. Place rail section on floor and extend chain straight out

(Fig. 1-2, B). Chain and rail should extend approximately 7 feet.

5.Remove wire ties and plastic bag from chain. Leave chain extended straight out on floor. Avoid kinks in the chain by careful handling and keeping chain flat on the floor.

6.Align the three rail sections by pulling the chain straight and wrapping it around the chain tensioner pulley (Fig. 1-3 & 1-4).

7.Attach the two rail clamps to the rail section joints with (4) bolts and nuts. After both rail clamps have been assembled to the rail sections, securely tighten the bolts and nuts.

Rail Assembly for BELT DRIVE OPENER

NOTE: For split rail clamps, nuts, and bolts locate Bag 0 from Box 1.

3.Remove the two rail sections that are not connected to the belt and place them on floor (Fig. 1-2, A).

4.Carefully remove the third rail section with belt. Place rail section on floor, remove ties on belt and extend belt straight out (Fig. 1-2, B). Avoid twists and kinks in the belt by careful handling and keeping belt flat on the floor. Belt and rail should extend approximately 7 feet.

5.Align the three rail sections by pulling the belt straight and wrapping it around the tensioner pulley (Fig. 1-3 & 1-4).

6.Attach the two rail clamps to the rail section joints with (4) bolts and nuts. After both rail clamps have been assembled to the rail sections, securely tighten the bolts and nuts.

CHAIN DRIVE RAILS

 

Chain Rail

Center Rail

A

 

End Rail

 

 

Chain Tensioner Pulley

B

 

Wire Tie(s)

 

BELT DRIVE RAILS

 

Belt Rail

 

A

Center Rail

 

 

End Rail

Tensioner Pulley

 

B

 

FIG. 1-2 Split Rail sections.

 

CHAIN

Rail with chain

 

 

 

 

 

 

 

 

 

Rail Clamps

 

 

 

 

 

 

 

 

 

Carriage Slide

Power Head

Rail Clamp Bolts

 

 

 

 

 

 

 

 

 

 

 

 

 

Release

 

 

 

 

 

 

Knob

 

Rail with belt

End Rail

 

Rail Clamp Nuts

 

 

 

 

 

 

 

 

 

 

N

 

 

 

 

 

 

NSIO

 

 

 

 

 

 

G TE

 

 

 

 

 

HIGH

SPRIN

 

 

 

 

 

 

 

 

 

 

 

 

 

Center Rail

 

 

 

 

Chain

 

 

 

 

 

 

 

 

 

 

 

Release

 

 

 

 

 

 

Knob

 

 

 

End Rail

 

 

ng

 

 

 

ION

 

BELT

 

 

 

G TENS

 

 

 

 

HIGH

SPRIN

 

 

 

 

 

 

 

 

 

 

 

Center Rail

 

 

 

 

 

 

 

 

 

 

Belt

 

 

FIG. 1-3

Split Rail assembly.

 

 

 

Wrap around tensioner pulley

FIG. 1-4

Mount chain/belt to tensioner pulley.

10

PN# 37026500123

02/26/2010 REV. 1

 

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models 2022/2024/2042 Safety Information Opener Features Table of ContentsSafety Features Do not USE AN Extension Cord MAX MIN Typical Sectional Door InstallationApprox Pg PgRecommended Tools Parts Identification Not Shown Full SizeDo not Return to Point of Purchase Power Head Piece Rail Hardware Assembled ViewBox Label Example Internal boxes Opener AssemblyBag Rail Assembly for Chain Drive Opener Belt adjustment Power Head & Rail AssemblyChain adjustment Chain Pulley Bracket at wall end of railDo not move door spring Mounting the header bracket Opener Installation Header and Door Mounting BracketsFinding header bracket mounting location ExtendGetting started Mounting the assemblyMounting the Opener Mounting StrapsInstall Door Arms Door Bracket2b. Wiring If not pre-wired Wall Control Installation2a. Wiring If pre-wired Wall Control locationDoor Control Open/Close Button Securely fasten wiresDo not install rear cover yet Mounting Independent Light Control3a. Wiring If not pre-wired SAFE-T-BEAMSYSTEM InstallationMounting Safe-T-BeamSource Red LED and Sensor Green LED 3b. Wiring pre-wired Power Head With Rear Cover RemovedWith Power Supplied Connecting to PowerWith Permanent Wiring With Grounded PlugDoor Limits Setting & Testing OPEN/CLOSE LimitsLimit Controls location on power head Close Travel LimitKeyed Emergency Release Purchased Separately Carriage LockKeyed Emergency Release Operation Instructions Erase OPEN/CLOSE Travel Limit UP/DOWN ForceContact Reverse Test Programming Remote Controls Lost or Stolen RemoteVisor clip Light BULB/LENS InstallationBattery replacement Light bulbDoor balance MaintenanceRoutine Monthly Maintenance Contact reverseAdvertencia Avertissement Circuit Wiring DiagramDisconnect power from opener prior to removing cover Opening Cover May Cause Electric ShockTroubleshooting Guide Operation Power head LED Troubleshooting Guide Power Head LEDPossible Problem Solution Green LEDTransmitter Compliance Statement Models 2022/2024/2042 This page left blank This page left blank This page left blank Solution Possible Problème Motorisée tête la de LEDSolución Problema Posible Fonctionnement Dépannage DE Guide Funcionamiento DE Problema Averías DE Investigación DE Guía Ruidoso FuncionamientoMantenimiento Avertissement MaintenanceAdvertencia Rutina DEAvertissement Ampoule + et polarité de marquesRobado O Perdido Remoto ’IC DE ET FCC LA DE Reglementation LA a ConformeMémoire la Effacer LED et code du AvertissementRemotos Controles DE Programación LED del yLe sous cm 10 x 5 de Colombe PorteLa de l’ouverture de centre Puerta la de vanoAvertissement Advertencia Advertencia AvertissementAdvertencia Puerta LA DE LímitesBeam-T-Safe de lalignement Vérifier Beam-T-Safe del alineación la VerifiqueGarde EN Mise Garde EN MisePrecaución PrecauciónCouvercle du Clips Arrière couvercle le InstallerPosterior tapa la Instale Tapa la de PresillasFuente y detector Del alambrado de Métodos Beam-T-Safe del Fuente y detector del LugaresSupport du centre Support languette soporte del lengüetaMarque Pared de control del Montaje Murale Commande la de MontageCoinçage MontagePelando y Partiendo Pared DE Control DEL InstalaciónDénudage et Division Pared de control Del alambre de RecorridoPuerta la de soporte Del colocación de Ejemplos PuertaLa de brazos los Acoplando La de soporte del MontajeExtra entramado necesita se No ExtraInutile supplémentaire Solivage Léchelle à pasInstallation InstalaciónCadena la de Ajuste Correa la de AjusteControl De caja la de Conjunto Riel Riel de partidas Secciones REV 02/26/2010 37026500123 PN#Partido riel del Conjunto PORTE-OUVRE pour rail de EnsembleInternes Boîtes ’OUVREURAbridor DEL Conjunto DEtiquette lExemple Emballer’INSTALLATION Instructions Importantes Assemblée Pièce 1 À Rail DU Quincaillerie LA DE VUE Pieza 1 DE Riel DEL Herrajes DE Montaje DEL VistaMANQUANTES? Pièces Recommandés Outils Recomendadas Herramientas Caja la de contenido del HojaMIN cm 12,7 po MAX cm 15 po 6 5 .MIN 6 .MAX OU / OPorte de types Ces ? verre ou verre de fibre Section la à reporterDe dessus-au situé mur du l’état Vérifier Et 4 sections aux reporter SeSección la a Refiérase Garaje su de puerta la en instalación para 2-GEREmergencia de salida de juego un considerar Abridor su instalar deSeguridad DE Características Matières DES TableÍndice Abridor DEL CaracterísticasTerre la à mis correctement être doit l’ouvreur Mort la voire blessuresGraves de entraîner Peut Mobiles pièces2022/2024/2042 Modeles/Modelos
Related manuals
Manual 29 pages 42.84 Kb

2024, 2042, 2022 specifications

Genie is a multi-faceted entertainment platform that has continually evolved since its inception. In 2022, Genie introduced significant updates that enhanced user experience, enabling content personalization through advanced algorithms. Users could access a vast library of shows, movies, and user-generated content tailored to their preferences. The interface saw an overhaul, featuring a sleek design that provided seamless navigation.

Cloud technology played a key role in Genie’s architecture, allowing users to access their content from any device. The transition to Adaptive Streaming Technology (AST) ensured that users experienced high-quality video regardless of their internet speed. Furthermore, Genie integrated social features, where users could share their favorite content, creating a community-driven environment.

By 2024, Genie had further capitalized on Artificial Intelligence (AI) and Machine Learning (ML) to refine its recommendation engine. The platform not only suggested content based on viewing histories but also analyzed social media trends to predict what users might enjoy next. With the introduction of GenieCast, users could share real-time reactions while watching content with friends, no matter their location.

In 2042, Genie transformed into an immersive entertainment ecosystem. The focus on Virtual Reality (VR) and Augmented Reality (AR) technologies allowed users to engage in interactive storytelling experiences. Users could step into the worlds of their favorite shows and movies, becoming part of the narratives. The integration of 360-degree video technology provided a fully immersive viewing experience.

Additionally, Genie’s partnership with various content creators ensured a rich array of exclusive content, appealing to diverse tastes. Enhanced security measures protected user data, ensuring privacy in this interconnected landscape. The collaboration with smart home devices allowed seamless integration, enabling voice-activated controls and personalized content delivery.

Overall, Genie’s evolution from 2022 through 2042 exemplifies the entertainment industry's shift towards user-centric experiences, advanced technologies, and interactive content delivery. With each iteration, Genie has solidified its position as a leader in the entertainment space, continually redefining how audiences engage with media. As technology progresses, users can anticipate even more innovative features that enhance their viewing experiences.
Top Page Image Contents