Genie 2022 Connecting to Power, With Grounded Plug, With Permanent Wiring, With Power Supplied

Page 19

5CONNECTING TO POWER

WARNING

To reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third (grounding) pin. This plug will only fit a grounded type outlet. If you do not have a grounded outlet, contact a qualified licensed electrician to install one. DO NOT alter the plug in any way. The door opener must be properly grounded in order to prevent personal injury and damage to the components.

DO NOT remove motor cover. All work performed on motor must be done by a trained door system technician.

CAUTION

Check local building codes to make sure that you are not required to have your garage door opener permanently wired, with circuit breaker protection. If building codes require door opener to be permanently wired have a qualified licensed electrician connect power with permanent wiring.

WITH GROUNDED PLUG:

Plug the opener into a properly grounded electrical outlet (Fig. 5-1).

WITH PERMANENT WIRING:

Instructions for Electrician.

Remove power from circuit.

Remove rear cover and motor cover.

Remove four motor cover screws (Fig. 5-2).

Remove existing power cord and strain relief from the 7/8" dia. hole and discard (Fig. 5-3).

Connect permanent wiring to power head using 7/8" diameter hole.

White to white/black to black/ground to green.

Use only UL recognized wire nuts.

Wires inside the power head must be at least 6" in length.

Replace motor cover and rear cover and re-energize the circuit.

NOTE: The Genie Company is not responsible for charges resulting from work performed by an independent electrician.

WITH POWER SUPPLIED:

Check Safe-T-Beam®alignment (Fig. 5-4).

Insure that no part of door or its hardware is in path between lenses of source and sensor.

Insure that tops of lenses are between 5" - 6" above the floor (Fig. 5-4). The brackets are flexible, and can be adjusted slightly if needed.

Adjust the Red LED transmitter by aiming the unit directly at the Green LED receiver. Use the adjustment screw located on the top of the transmitter housing to make adjustments.

The Red LED transmitter will blink if there is a misalignment. When the LED units are aligned the Red LED will remain ON continuously.

After the alignment is finished tighten the adjustment screws on both sensors.

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

FIG. 5-1 Connect to power.

Motor Cover Screws

FIG. 5-2 Remove motor cover.

(Electrican ONLY)

FIG. 5-3 Power cord strain relief.

CAUTION

Do NOT use an extension cord.

Do NOT use a portable generator. This product is designed to operate using standard household current.

Do NOT use alternate power supplies.

 

 

 

 

o

m

fl

o

o

r

 

 

 

fr

r

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

" m

ax

om

fl

o

o

 

 

 

 

 

 

 

 

 

in

fr

 

 

 

 

 

 

5" m

 

 

 

 

 

 

 

FIG. 5-4 Check Safe-T-Beam®alignment.

INFRARED PROTECTION FUNCTION

1.When the garage door is opening, its movement will not be influenced if the Safe-T-Beam®is obstructed.

2.If the Safe-T-Beam®is obstructed before the garage door fully closes, the door will not close.

3.When the garage door is closing, if Safe-T-Beam®is cut off by people or obstacle, the garage door will reverse automatically to its fully opened position. (Meanwhile, the opener light will keep blinking until door moves to its fully opened position.)

4.If the Safe-T-Beam®System fails, loses power, or is installed improperly, press and hold the Wall Control "open/close" button until the door reaches its fully closed position. The LED indicator light on the power head will be green and blink twice (Pattern: ☼☼ pause ☼☼ pause) to inform you to eliminate the problem first.

If you release the "open/close" button on the Wall Control during the closing movement the door will reverse automatically to its fully opened position.

PN# 37026500123

02/26/2010 REV. 1

19

 

Image 19
Contents Models 2022/2024/2042 Safety Information Opener Features Table of ContentsSafety Features Do not USE AN Extension Cord Pg Pg Typical Sectional Door InstallationApprox MAX MINParts Identification Not Shown Full Size Recommended ToolsDo not Return to Point of Purchase Piece Rail Hardware Assembled View Power HeadBox Label Example Internal boxes Opener AssemblyBag Rail Assembly for Chain Drive Opener Chain Pulley Bracket at wall end of rail Power Head & Rail AssemblyChain adjustment Belt adjustmentExtend Opener Installation Header and Door Mounting BracketsFinding header bracket mounting location Do not move door spring Mounting the header bracketMounting Straps Mounting the assemblyMounting the Opener Getting startedDoor Bracket Install Door ArmsWall Control location Wall Control Installation2a. Wiring If pre-wired 2b. Wiring If not pre-wiredIndependent Light Control Securely fasten wiresDo not install rear cover yet Mounting Door Control Open/Close Button3a. Wiring If not pre-wired SAFE-T-BEAMSYSTEM InstallationMounting Safe-T-BeamSource Red LED and Sensor Green LED Power Head With Rear Cover Removed 3b. Wiring pre-wiredWith Grounded Plug Connecting to PowerWith Permanent Wiring With Power SuppliedClose Travel Limit Setting & Testing OPEN/CLOSE LimitsLimit Controls location on power head Door LimitsKeyed Emergency Release Purchased Separately Carriage LockKeyed Emergency Release Operation Instructions Erase OPEN/CLOSE Travel Limit UP/DOWN ForceContact Reverse Test Lost or Stolen Remote Programming Remote ControlsLight bulb Light BULB/LENS InstallationBattery replacement Visor clipContact reverse MaintenanceRoutine Monthly Maintenance Door balanceOpening Cover May Cause Electric Shock Circuit Wiring DiagramDisconnect power from opener prior to removing cover Advertencia AvertissementTroubleshooting Guide Operation Green LED Troubleshooting Guide Power Head LEDPossible Problem Solution Power head LEDTransmitter Compliance Statement Models 2022/2024/2042 This page left blank This page left blank This page left blank Motorisée tête la de LED Solution Possible ProblèmeSolución Problema Posible Fonctionnement Dépannage DE Guide Ruidoso Funcionamiento Funcionamiento DE Problema Averías DE Investigación DE GuíaRutina DE Avertissement MaintenanceAdvertencia MantenimientoAvertissement + et polarité de marques AmpouleRobado O Perdido Remoto ’IC DE ET FCC LA DE Reglementation LA a ConformeMémoire la Effacer LED del y AvertissementRemotos Controles DE Programación LED et code duPuerta la de vano PorteLa de l’ouverture de centre Le sous cm 10 x 5 de ColombeAvertissement Advertencia Puerta LA DE Límites AvertissementAdvertencia AdvertenciaBeam-T-Safe del alineación la Verifique Beam-T-Safe de lalignement VérifierPrecaución Garde EN MisePrecaución Garde EN MiseTapa la de Presillas Arrière couvercle le InstallerPosterior tapa la Instale Couvercle du ClipsBeam-T-Safe del Fuente y detector del Lugares Fuente y detector Del alambrado de MétodosSupport du centre Support languette soporte del lengüetaMarque Montage Murale Commande la de MontageCoinçage Pared de control del MontajePared de control Del alambre de Recorrido Pared DE Control DEL InstalaciónDénudage et Division Pelando y PartiendoLa de soporte del Montaje PuertaLa de brazos los Acoplando Puerta la de soporte Del colocación de EjemplosLéchelle à pas ExtraInutile supplémentaire Solivage Extra entramado necesita se NoInstalación InstallationCadena la de Ajuste Correa la de AjusteControl De caja la de Conjunto Riel PORTE-OUVRE pour rail de Ensemble REV 02/26/2010 37026500123 PN#Partido riel del Conjunto Riel de partidas SeccionesDEtiquette lExemple Emballer ’OUVREURAbridor DEL Conjunto Internes Boîtes’INSTALLATION Instructions Importantes Pieza 1 DE Riel DEL Herrajes DE Montaje DEL Vista Assemblée Pièce 1 À Rail DU Quincaillerie LA DE VUEMANQUANTES? Pièces Caja la de contenido del Hoja Recommandés Outils Recomendadas HerramientasOU / O MIN cm 12,7 po MAX cm 15 po 6 5 .MIN 6 .MAXEt 4 sections aux reporter Se Section la à reporterDe dessus-au situé mur du l’état Vérifier Porte de types Ces ? verre ou verre de fibreAbridor su instalar de Garaje su de puerta la en instalación para 2-GEREmergencia de salida de juego un considerar Sección la a RefiéraseAbridor DEL Características Matières DES TableÍndice Seguridad DE CaracterísticasMobiles pièces Mort la voire blessuresGraves de entraîner Peut Terre la à mis correctement être doit l’ouvreur2022/2024/2042 Modeles/Modelos
Related manuals
Manual 29 pages 42.84 Kb

2024, 2042, 2022 specifications

Genie is a multi-faceted entertainment platform that has continually evolved since its inception. In 2022, Genie introduced significant updates that enhanced user experience, enabling content personalization through advanced algorithms. Users could access a vast library of shows, movies, and user-generated content tailored to their preferences. The interface saw an overhaul, featuring a sleek design that provided seamless navigation.

Cloud technology played a key role in Genie’s architecture, allowing users to access their content from any device. The transition to Adaptive Streaming Technology (AST) ensured that users experienced high-quality video regardless of their internet speed. Furthermore, Genie integrated social features, where users could share their favorite content, creating a community-driven environment.

By 2024, Genie had further capitalized on Artificial Intelligence (AI) and Machine Learning (ML) to refine its recommendation engine. The platform not only suggested content based on viewing histories but also analyzed social media trends to predict what users might enjoy next. With the introduction of GenieCast, users could share real-time reactions while watching content with friends, no matter their location.

In 2042, Genie transformed into an immersive entertainment ecosystem. The focus on Virtual Reality (VR) and Augmented Reality (AR) technologies allowed users to engage in interactive storytelling experiences. Users could step into the worlds of their favorite shows and movies, becoming part of the narratives. The integration of 360-degree video technology provided a fully immersive viewing experience.

Additionally, Genie’s partnership with various content creators ensured a rich array of exclusive content, appealing to diverse tastes. Enhanced security measures protected user data, ensuring privacy in this interconnected landscape. The collaboration with smart home devices allowed seamless integration, enabling voice-activated controls and personalized content delivery.

Overall, Genie’s evolution from 2022 through 2042 exemplifies the entertainment industry's shift towards user-centric experiences, advanced technologies, and interactive content delivery. With each iteration, Genie has solidified its position as a leader in the entertainment space, continually redefining how audiences engage with media. As technology progresses, users can anticipate even more innovative features that enhance their viewing experiences.