Genie 2024, 2042, 2022 manual Programming Remote Controls, Lost or Stolen Remote

Page 23

7PROGRAMMING REMOTE CONTROLS

WARNING

A moving door can cause serious injury or death.

1.Keep people clear of opening while door is moving.

2.Do NOT allow children to play with opener, including Wall Control, remote control, or Wireless Keypad.

3.During programming, the door opener could begin to run, so keep people and objects away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the Opener by pulling the Emergency Release.

NOTE: For remote control locate Box 3.

1a. Single Button Remote Programming.

NOTE: This opener can learn up to 7 transmitter buttons.

LEARN

Locate "Learn Code" CODE button and indicator LED on the power head (Fig. 7-1).

Press and release "Learn Code" button.

Indicator LED will blink RED at a rate of twice per second.

Within 30 seconds, push remote control button once.

Indicator LED will stop blinking and stay ON.

Press remote control button again.

Red LED will go out. Remote is now programmed and ready for use.

1b. Multi Button Remote Programming.

NOTE: Each button on a multi-button remote is designed for use with 1 door. You cannot program 2 buttons to operate the same door, nor can you program 1 button to operate 2 doors. You can program a maximum of 7 different transmitters or wireless devices.

NOTE: Pushing two buttons on power head simultaneously will erase programmed memory and limits must be reset.

For each button.

Program each button separately using the Single Button Remote Programming steps.

2.Operating.

Press remote button once.

Door will move.

Press button again.

Door will stop.

Press button again.

Door will move in opposite direction.

NOTE: The door will stop automatically at the fully open or fully closed position.

LOST OR STOLEN REMOTE

1. Clear memory.

LEARN

Press and hold "Learn Code" CODE button (on power head) for 10 seconds or until the red blinking indicator LED goes out.

Program remaining or new remote controls as done previously. Your door opener will no longer recognize any signal received from the missing remote control, or any other which has not been reprogrammed.

NOTE: To program a

Homelink® and Car2U®

device follow the Homelink® or Car2U® instructions in your car owner’s manual.

FCC and IC CERTIFIED

This device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which may be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

Re-orient or relocate the receiver antenna.

Increase the separation between the opener and receiver.

Connect the opener into an outlet on a circuit different from that to which the receiver is connected.

Consult your local dealer.

NOTE: Wall control will not operate until limits are set.

Limit controls location on power head.

LED

Open

Open

 

 

Indicator Light

Set Limit

 

Up Force

Travel Limit

 

 

 

Button

OPEN Control

 

 

 

 

 

 

 

 

Adjustment

To

 

 

SET

 

 

Garage Door

 

 

 

 

 

 

 

 

 

 

LEARN MANUAL LIMIT

FORCE

 

 

 

 

SET

 

 

Learn

 

 

 

 

 

Code

CODE

Close

Close

CLOSE

Down Force

Button

 

 

 

 

 

Travel Limit Set Limit

 

Control

 

 

 

Button

 

Adjustment

FIG. 7-1 Learn code button and LED

PN# 37026500123

02/26/2010 REV. 1

23

Image 23
Contents Models 2022/2024/2042 Safety Information Safety Features Table of ContentsOpener Features Do not USE AN Extension Cord Pg Pg Typical Sectional Door InstallationApprox MAX MINParts Identification Not Shown Full Size Recommended ToolsDo not Return to Point of Purchase Piece Rail Hardware Assembled View Power HeadBag Opener AssemblyBox Label Example Internal boxes Rail Assembly for Chain Drive Opener Chain Pulley Bracket at wall end of rail Power Head & Rail AssemblyChain adjustment Belt adjustmentExtend Opener Installation Header and Door Mounting BracketsFinding header bracket mounting location Do not move door spring Mounting the header bracketMounting Straps Mounting the assemblyMounting the Opener Getting startedDoor Bracket Install Door ArmsWall Control location Wall Control Installation2a. Wiring If pre-wired 2b. Wiring If not pre-wiredIndependent Light Control Securely fasten wiresDo not install rear cover yet Mounting Door Control Open/Close ButtonMounting Safe-T-BeamSource Red LED and Sensor Green LED SAFE-T-BEAMSYSTEM Installation3a. Wiring If not pre-wired Power Head With Rear Cover Removed 3b. Wiring pre-wiredWith Grounded Plug Connecting to PowerWith Permanent Wiring With Power SuppliedClose Travel Limit Setting & Testing OPEN/CLOSE LimitsLimit Controls location on power head Door LimitsKeyed Emergency Release Operation Instructions Carriage LockKeyed Emergency Release Purchased Separately Contact Reverse Test UP/DOWN ForceErase OPEN/CLOSE Travel Limit Lost or Stolen Remote Programming Remote ControlsLight bulb Light BULB/LENS InstallationBattery replacement Visor clipContact reverse MaintenanceRoutine Monthly Maintenance Door balanceOpening Cover May Cause Electric Shock Circuit Wiring DiagramDisconnect power from opener prior to removing cover Advertencia AvertissementTroubleshooting Guide Operation Green LED Troubleshooting Guide Power Head LEDPossible Problem Solution Power head LEDTransmitter Compliance Statement Models 2022/2024/2042 This page left blank This page left blank This page left blank Motorisée tête la de LED Solution Possible ProblèmeSolución Problema Posible Fonctionnement Dépannage DE Guide Ruidoso Funcionamiento Funcionamiento DE Problema Averías DE Investigación DE GuíaRutina DE Avertissement MaintenanceAdvertencia MantenimientoAvertissement + et polarité de marques AmpouleMémoire la Effacer ’IC DE ET FCC LA DE Reglementation LA a ConformeRobado O Perdido Remoto LED del y AvertissementRemotos Controles DE Programación LED et code duPuerta la de vano PorteLa de l’ouverture de centre Le sous cm 10 x 5 de ColombeAvertissement Advertencia Puerta LA DE Límites AvertissementAdvertencia AdvertenciaBeam-T-Safe del alineación la Verifique Beam-T-Safe de lalignement VérifierPrecaución Garde EN MisePrecaución Garde EN MiseTapa la de Presillas Arrière couvercle le InstallerPosterior tapa la Instale Couvercle du ClipsBeam-T-Safe del Fuente y detector del Lugares Fuente y detector Del alambrado de MétodosMarque Support languette soporte del lengüetaSupport du centre Montage Murale Commande la de MontageCoinçage Pared de control del MontajePared de control Del alambre de Recorrido Pared DE Control DEL InstalaciónDénudage et Division Pelando y PartiendoLa de soporte del Montaje PuertaLa de brazos los Acoplando Puerta la de soporte Del colocación de EjemplosLéchelle à pas ExtraInutile supplémentaire Solivage Extra entramado necesita se NoInstalación InstallationControl De caja la de Conjunto Riel Correa la de AjusteCadena la de Ajuste PORTE-OUVRE pour rail de Ensemble REV 02/26/2010 37026500123 PN#Partido riel del Conjunto Riel de partidas SeccionesDEtiquette lExemple Emballer ’OUVREURAbridor DEL Conjunto Internes Boîtes’INSTALLATION Instructions Importantes Pieza 1 DE Riel DEL Herrajes DE Montaje DEL Vista Assemblée Pièce 1 À Rail DU Quincaillerie LA DE VUEMANQUANTES? Pièces Caja la de contenido del Hoja Recommandés Outils Recomendadas HerramientasOU / O MIN cm 12,7 po MAX cm 15 po 6 5 .MIN 6 .MAXEt 4 sections aux reporter Se Section la à reporterDe dessus-au situé mur du l’état Vérifier Porte de types Ces ? verre ou verre de fibreAbridor su instalar de Garaje su de puerta la en instalación para 2-GEREmergencia de salida de juego un considerar Sección la a RefiéraseAbridor DEL Características Matières DES TableÍndice Seguridad DE CaracterísticasMobiles pièces Mort la voire blessuresGraves de entraîner Peut Terre la à mis correctement être doit l’ouvreur2022/2024/2042 Modeles/Modelos
Related manuals
Manual 29 pages 42.84 Kb

2024, 2042, 2022 specifications

Genie is a multi-faceted entertainment platform that has continually evolved since its inception. In 2022, Genie introduced significant updates that enhanced user experience, enabling content personalization through advanced algorithms. Users could access a vast library of shows, movies, and user-generated content tailored to their preferences. The interface saw an overhaul, featuring a sleek design that provided seamless navigation.

Cloud technology played a key role in Genie’s architecture, allowing users to access their content from any device. The transition to Adaptive Streaming Technology (AST) ensured that users experienced high-quality video regardless of their internet speed. Furthermore, Genie integrated social features, where users could share their favorite content, creating a community-driven environment.

By 2024, Genie had further capitalized on Artificial Intelligence (AI) and Machine Learning (ML) to refine its recommendation engine. The platform not only suggested content based on viewing histories but also analyzed social media trends to predict what users might enjoy next. With the introduction of GenieCast, users could share real-time reactions while watching content with friends, no matter their location.

In 2042, Genie transformed into an immersive entertainment ecosystem. The focus on Virtual Reality (VR) and Augmented Reality (AR) technologies allowed users to engage in interactive storytelling experiences. Users could step into the worlds of their favorite shows and movies, becoming part of the narratives. The integration of 360-degree video technology provided a fully immersive viewing experience.

Additionally, Genie’s partnership with various content creators ensured a rich array of exclusive content, appealing to diverse tastes. Enhanced security measures protected user data, ensuring privacy in this interconnected landscape. The collaboration with smart home devices allowed seamless integration, enabling voice-activated controls and personalized content delivery.

Overall, Genie’s evolution from 2022 through 2042 exemplifies the entertainment industry's shift towards user-centric experiences, advanced technologies, and interactive content delivery. With each iteration, Genie has solidified its position as a leader in the entertainment space, continually redefining how audiences engage with media. As technology progresses, users can anticipate even more innovative features that enhance their viewing experiences.