Genie 2024, 2042, 2022 manual Power Head & Rail Assembly, Chain adjustment, Belt adjustment

Page 11

POWER HEAD & RAIL ASSEMBLY

Assembly for CHAIN DRIVE OPENER

NOTE: Handle carefully! Drive chain can slide out of rail.

NOTE: For power head and rail assembly locate Bag 1 from Box 1.

NOTE: Copy serial number from power head frame and record it on warranty page.

1.Attach rail assembly to power head by aligning the sprocket onto the motor shaft. Use (3) bolts, 5/16 -18 x 1/2" (Fig. 1-5).

2.Tighten the chain by turning the adjustment nut clockwise. The chain adjustment nut is located in the Chain Pulley Bracket (opposite rail end from the power head) (Fig. 1-6).

3.Tighten chain until chain is approximately 1/8 inch above the base of the rail at midpoint on the rail (Fig. 1-6). Do NOT over tighten chain.

CAUTION

You should have removed all ropes and/or cables (NOT door lift cables) and disabled the door lock already. If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8).

Set assembled power head and rail aside. Begin with Section 2 INSTALLATION.

Assembly for BELT DRIVE OPENER

NOTE: For power head and rail assembly locate Bag 1 from Box 1.

NOTE: Copy serial number from power head frame and record it on warranty page.

1.Attach rail assembly to power head by aligning the sprocket onto the motor shaft. Use (3) bolts, 5/16 -18 x 1/2" (Fig. 1-5).

2.Tighten the belt by turning the adjustment nut clockwise. The belt adjustment nut is located in the Belt Pulley Bracket (opposite rail end from the power head) (Fig. 1-7).

3.Tighten belt until belt is approximately 1/8 inch above the base of the rail at midpoint on the rail (Fig. 1-7). Do NOT over tighten belt.

CAUTION

You should have removed all ropes and/or cables (NOT door lift cables) and disabled the door lock already. If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8).

Set assembled power head and rail aside. Begin with Section 2 INSTALLATION.

Use

5/16"-18 x 1/2" Bolts

FIG. 1-5 Rail - Power head assembly.

 

Chain Pulley Bracket (at wall end of rail)

 

 

Use 1/2" socket

 

 

on adjustment nut

 

 

Tighten nut to move pulley this direction

 

 

Chain

 

 

Chain

 

 

1/8"

 

 

T-Rail at center of rail assembly

T-Rail

 

 

FIG. 1-6

Chain adjustment.

 

 

Belt Pulley Bracket (at wall end of rail)

 

 

Use 1/2" socket

 

 

on adjustment nut

 

 

Tighten nut to move pulley this direction

 

 

Belt

 

 

Belt

 

 

1/8"

 

 

T-Rail at center of rail assembly

T-Rail

 

 

FIG. 1-7

Belt adjustment.

 

Remove

Remove

FIG. 1-8 Disable garage door lock.

PN# 37026500123

02/26/2010 REV. 1

11

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Models 2022/2024/2042 Safety Information Safety Features Table of ContentsOpener Features Do not USE AN Extension Cord Pg Pg Typical Sectional Door InstallationApprox MAX MINParts Identification Not Shown Full Size Recommended ToolsDo not Return to Point of Purchase Piece Rail Hardware Assembled View Power HeadBag Opener AssemblyBox Label Example Internal boxes Rail Assembly for Chain Drive Opener Chain Pulley Bracket at wall end of rail Power Head & Rail AssemblyChain adjustment Belt adjustmentExtend Opener Installation Header and Door Mounting BracketsFinding header bracket mounting location Do not move door spring Mounting the header bracketMounting Straps Mounting the assemblyMounting the Opener Getting startedDoor Bracket Install Door ArmsWall Control location Wall Control Installation2a. Wiring If pre-wired 2b. Wiring If not pre-wiredIndependent Light Control Securely fasten wiresDo not install rear cover yet Mounting Door Control Open/Close ButtonMounting Safe-T-BeamSource Red LED and Sensor Green LED SAFE-T-BEAMSYSTEM Installation3a. Wiring If not pre-wired Power Head With Rear Cover Removed 3b. Wiring pre-wiredWith Grounded Plug Connecting to PowerWith Permanent Wiring With Power SuppliedClose Travel Limit Setting & Testing OPEN/CLOSE LimitsLimit Controls location on power head Door LimitsKeyed Emergency Release Operation Instructions Carriage LockKeyed Emergency Release Purchased Separately Contact Reverse Test UP/DOWN ForceErase OPEN/CLOSE Travel Limit Lost or Stolen Remote Programming Remote ControlsLight bulb Light BULB/LENS InstallationBattery replacement Visor clipContact reverse MaintenanceRoutine Monthly Maintenance Door balanceOpening Cover May Cause Electric Shock Circuit Wiring DiagramDisconnect power from opener prior to removing cover Advertencia AvertissementTroubleshooting Guide Operation Green LED Troubleshooting Guide Power Head LEDPossible Problem Solution Power head LEDTransmitter Compliance Statement Models 2022/2024/2042 This page left blank This page left blank This page left blank Motorisée tête la de LED Solution Possible ProblèmeSolución Problema Posible Fonctionnement Dépannage DE Guide Ruidoso Funcionamiento Funcionamiento DE Problema Averías DE Investigación DE GuíaRutina DE Avertissement MaintenanceAdvertencia MantenimientoAvertissement + et polarité de marques AmpouleMémoire la Effacer ’IC DE ET FCC LA DE Reglementation LA a ConformeRobado O Perdido Remoto LED del y AvertissementRemotos Controles DE Programación LED et code duPuerta la de vano PorteLa de l’ouverture de centre Le sous cm 10 x 5 de ColombeAvertissement Advertencia Puerta LA DE Límites AvertissementAdvertencia AdvertenciaBeam-T-Safe del alineación la Verifique Beam-T-Safe de lalignement VérifierPrecaución Garde EN MisePrecaución Garde EN MiseTapa la de Presillas Arrière couvercle le InstallerPosterior tapa la Instale Couvercle du ClipsBeam-T-Safe del Fuente y detector del Lugares Fuente y detector Del alambrado de MétodosMarque Support languette soporte del lengüetaSupport du centre Montage Murale Commande la de MontageCoinçage Pared de control del MontajePared de control Del alambre de Recorrido Pared DE Control DEL InstalaciónDénudage et Division Pelando y PartiendoLa de soporte del Montaje PuertaLa de brazos los Acoplando Puerta la de soporte Del colocación de EjemplosLéchelle à pas ExtraInutile supplémentaire Solivage Extra entramado necesita se NoInstalación InstallationControl De caja la de Conjunto Riel Correa la de AjusteCadena la de Ajuste PORTE-OUVRE pour rail de Ensemble REV 02/26/2010 37026500123 PN#Partido riel del Conjunto Riel de partidas SeccionesDEtiquette lExemple Emballer ’OUVREURAbridor DEL Conjunto Internes Boîtes’INSTALLATION Instructions Importantes Pieza 1 DE Riel DEL Herrajes DE Montaje DEL Vista Assemblée Pièce 1 À Rail DU Quincaillerie LA DE VUEMANQUANTES? Pièces Caja la de contenido del Hoja Recommandés Outils Recomendadas HerramientasOU / O MIN cm 12,7 po MAX cm 15 po 6 5 .MIN 6 .MAXEt 4 sections aux reporter Se Section la à reporterDe dessus-au situé mur du l’état Vérifier Porte de types Ces ? verre ou verre de fibreAbridor su instalar de Garaje su de puerta la en instalación para 2-GEREmergencia de salida de juego un considerar Sección la a RefiéraseAbridor DEL Características Matières DES TableÍndice Seguridad DE CaracterísticasMobiles pièces Mort la voire blessuresGraves de entraîner Peut Terre la à mis correctement être doit l’ouvreur2022/2024/2042 Modeles/Modelos
Related manuals
Manual 29 pages 42.84 Kb

2024, 2042, 2022 specifications

Genie is a multi-faceted entertainment platform that has continually evolved since its inception. In 2022, Genie introduced significant updates that enhanced user experience, enabling content personalization through advanced algorithms. Users could access a vast library of shows, movies, and user-generated content tailored to their preferences. The interface saw an overhaul, featuring a sleek design that provided seamless navigation.

Cloud technology played a key role in Genie’s architecture, allowing users to access their content from any device. The transition to Adaptive Streaming Technology (AST) ensured that users experienced high-quality video regardless of their internet speed. Furthermore, Genie integrated social features, where users could share their favorite content, creating a community-driven environment.

By 2024, Genie had further capitalized on Artificial Intelligence (AI) and Machine Learning (ML) to refine its recommendation engine. The platform not only suggested content based on viewing histories but also analyzed social media trends to predict what users might enjoy next. With the introduction of GenieCast, users could share real-time reactions while watching content with friends, no matter their location.

In 2042, Genie transformed into an immersive entertainment ecosystem. The focus on Virtual Reality (VR) and Augmented Reality (AR) technologies allowed users to engage in interactive storytelling experiences. Users could step into the worlds of their favorite shows and movies, becoming part of the narratives. The integration of 360-degree video technology provided a fully immersive viewing experience.

Additionally, Genie’s partnership with various content creators ensured a rich array of exclusive content, appealing to diverse tastes. Enhanced security measures protected user data, ensuring privacy in this interconnected landscape. The collaboration with smart home devices allowed seamless integration, enabling voice-activated controls and personalized content delivery.

Overall, Genie’s evolution from 2022 through 2042 exemplifies the entertainment industry's shift towards user-centric experiences, advanced technologies, and interactive content delivery. With each iteration, Genie has solidified its position as a leader in the entertainment space, continually redefining how audiences engage with media. As technology progresses, users can anticipate even more innovative features that enhance their viewing experiences.
Top Page Image Contents