Genie 2042, 2022 Light BULB/LENS Installation, Battery replacement, Visor clip, Light bulb, Lens

Page 24

8 REMOTE CONTROL BATTERY REPLACEMENT AND VISOR CLIP INSTALLATION

1.Battery replacement.

To open, gently push straight out on battery cover lock tab as shown. (Fig. 8-1).

Slide open battery cover.

Remove old battery.

Make sure new battery is facing proper direction (Match battery polarity with symbols inside battery housing) (Fig. 8-2).

Recommended replacement battery type: Alkaline A23, 12 volt.

NOTE: Batteries differ in care and maintenance. Follow the manufacturer’s directions for battery maintenance, replacement, and use.

Slip new battery into place.

Slide battery cover until it clicks shut.

Operate remote to make sure it is working properly. (No re-programming is needed.)

2.Visor clip.

(The visor clip may come already installed.)You will have to install the visor clip if you choose to attach your remote to the car visor.

Slide visor clip into back of remote control.

It will snap into place (Fig. 8-3).

FIG. 8-3

Attach visor clip.

Slide out

FIG. 8-1 Open battery cover.

– and + polarity marks

FIG. 8-2 Match battery polarity.

9LIGHT BULB/LENS INSTALLATION

WARNING

For added safety and protection please unplug opener before installing light bulb.

NOTE: For lens covers locate Box 4.

1.Light bulb.

Recommendations.

Do NOT use a short neck bulb.

Light bulbs should be no more than 60 Watts.

Use a heavy duty service bulb for longer life.

Screw 1 bulb into each socket.

2.Lens.

Select a white (lamp) cover.

On the power head end nearest the garage door, line up lamp lens tabs on power head with corresponding slots in lens (Fig. 9-1).

Slide lens onto power head. Make sure the tabs are fully engaged into lens slots (Fig. 9-2).

Repeat for rear lens on power head.

Plug power cord back into electrical outlet.

Test lamp operation.

Light bulb socket

Lens tabs

Light bulb socket

FIG. 9-1 Slide each lens onto motor cover.

FIG. 9-2

Fasten lens.

24

PN# 37026500123

02/26/2010 REV. 1

 

Image 24
Contents Models 2022/2024/2042 Safety Information Table of Contents Opener FeaturesSafety Features Do not USE AN Extension Cord Typical Sectional Door Installation ApproxMAX MIN Pg PgRecommended Tools Parts Identification Not Shown Full SizeDo not Return to Point of Purchase Power Head Piece Rail Hardware Assembled ViewOpener Assembly Box Label Example Internal boxesBag Rail Assembly for Chain Drive Opener Power Head & Rail Assembly Chain adjustmentBelt adjustment Chain Pulley Bracket at wall end of railOpener Installation Header and Door Mounting Brackets Finding header bracket mounting locationDo not move door spring Mounting the header bracket ExtendMounting the assembly Mounting the OpenerGetting started Mounting StrapsInstall Door Arms Door BracketWall Control Installation 2a. Wiring If pre-wired2b. Wiring If not pre-wired Wall Control locationSecurely fasten wires Do not install rear cover yet MountingDoor Control Open/Close Button Independent Light ControlSAFE-T-BEAMSYSTEM Installation 3a. Wiring If not pre-wiredMounting Safe-T-BeamSource Red LED and Sensor Green LED 3b. Wiring pre-wired Power Head With Rear Cover RemovedConnecting to Power With Permanent WiringWith Power Supplied With Grounded PlugSetting & Testing OPEN/CLOSE Limits Limit Controls location on power headDoor Limits Close Travel LimitCarriage Lock Keyed Emergency Release Purchased SeparatelyKeyed Emergency Release Operation Instructions UP/DOWN Force Erase OPEN/CLOSE Travel LimitContact Reverse Test Programming Remote Controls Lost or Stolen RemoteLight BULB/LENS Installation Battery replacementVisor clip Light bulbMaintenance Routine Monthly MaintenanceDoor balance Contact reverseCircuit Wiring Diagram Disconnect power from opener prior to removing coverAdvertencia Avertissement Opening Cover May Cause Electric ShockTroubleshooting Guide Operation Troubleshooting Guide Power Head LED Possible Problem SolutionPower head LED Green LEDTransmitter Compliance Statement Models 2022/2024/2042 This page left blank This page left blank This page left blank Solution Possible Problème Motorisée tête la de LEDSolución Problema Posible Fonctionnement Dépannage DE Guide Funcionamiento DE Problema Averías DE Investigación DE Guía Ruidoso FuncionamientoAvertissement Maintenance AdvertenciaMantenimiento Rutina DEAvertissement Ampoule + et polarité de marques’IC DE ET FCC LA DE Reglementation LA a Conforme Robado O Perdido RemotoMémoire la Effacer Avertissement Remotos Controles DE ProgramaciónLED et code du LED del yPorte La de l’ouverture de centreLe sous cm 10 x 5 de Colombe Puerta la de vanoAvertissement Advertencia Avertissement AdvertenciaAdvertencia Puerta LA DE LímitesBeam-T-Safe de lalignement Vérifier Beam-T-Safe del alineación la VerifiqueGarde EN Mise PrecauciónGarde EN Mise PrecauciónArrière couvercle le Installer Posterior tapa la InstaleCouvercle du Clips Tapa la de PresillasFuente y detector Del alambrado de Métodos Beam-T-Safe del Fuente y detector del LugaresSupport languette soporte del lengüeta Support du centreMarque Murale Commande la de Montage CoinçagePared de control del Montaje MontagePared DE Control DEL Instalación Dénudage et DivisionPelando y Partiendo Pared de control Del alambre de RecorridoPuerta La de brazos los AcoplandoPuerta la de soporte Del colocación de Ejemplos La de soporte del MontajeExtra Inutile supplémentaire SolivageExtra entramado necesita se No Léchelle à pasInstallation InstalaciónCorrea la de Ajuste Cadena la de AjusteControl De caja la de Conjunto Riel REV 02/26/2010 37026500123 PN# Partido riel del ConjuntoRiel de partidas Secciones PORTE-OUVRE pour rail de Ensemble’OUVREUR Abridor DEL ConjuntoInternes Boîtes DEtiquette lExemple Emballer’INSTALLATION Instructions Importantes Assemblée Pièce 1 À Rail DU Quincaillerie LA DE VUE Pieza 1 DE Riel DEL Herrajes DE Montaje DEL VistaMANQUANTES? Pièces Recommandés Outils Recomendadas Herramientas Caja la de contenido del HojaMIN cm 12,7 po MAX cm 15 po 6 5 .MIN 6 .MAX OU / OSection la à reporter De dessus-au situé mur du l’état VérifierPorte de types Ces ? verre ou verre de fibre Et 4 sections aux reporter SeGaraje su de puerta la en instalación para 2-GER Emergencia de salida de juego un considerarSección la a Refiérase Abridor su instalar deMatières DES Table ÍndiceSeguridad DE Características Abridor DEL CaracterísticasMort la voire blessures Graves de entraîner PeutTerre la à mis correctement être doit l’ouvreur Mobiles pièces2022/2024/2042 Modeles/Modelos
Related manuals
Manual 29 pages 42.84 Kb

2024, 2042, 2022 specifications

Genie is a multi-faceted entertainment platform that has continually evolved since its inception. In 2022, Genie introduced significant updates that enhanced user experience, enabling content personalization through advanced algorithms. Users could access a vast library of shows, movies, and user-generated content tailored to their preferences. The interface saw an overhaul, featuring a sleek design that provided seamless navigation.

Cloud technology played a key role in Genie’s architecture, allowing users to access their content from any device. The transition to Adaptive Streaming Technology (AST) ensured that users experienced high-quality video regardless of their internet speed. Furthermore, Genie integrated social features, where users could share their favorite content, creating a community-driven environment.

By 2024, Genie had further capitalized on Artificial Intelligence (AI) and Machine Learning (ML) to refine its recommendation engine. The platform not only suggested content based on viewing histories but also analyzed social media trends to predict what users might enjoy next. With the introduction of GenieCast, users could share real-time reactions while watching content with friends, no matter their location.

In 2042, Genie transformed into an immersive entertainment ecosystem. The focus on Virtual Reality (VR) and Augmented Reality (AR) technologies allowed users to engage in interactive storytelling experiences. Users could step into the worlds of their favorite shows and movies, becoming part of the narratives. The integration of 360-degree video technology provided a fully immersive viewing experience.

Additionally, Genie’s partnership with various content creators ensured a rich array of exclusive content, appealing to diverse tastes. Enhanced security measures protected user data, ensuring privacy in this interconnected landscape. The collaboration with smart home devices allowed seamless integration, enabling voice-activated controls and personalized content delivery.

Overall, Genie’s evolution from 2022 through 2042 exemplifies the entertainment industry's shift towards user-centric experiences, advanced technologies, and interactive content delivery. With each iteration, Genie has solidified its position as a leader in the entertainment space, continually redefining how audiences engage with media. As technology progresses, users can anticipate even more innovative features that enhance their viewing experiences.