Linear AUH-S, AUJ-S owner manual Settable Switches Location

OPERATION & ADJUSTMENT INSTRUCTIONS	17
SETTING THE SWITCH SELECTABLE OPERATING MODES

Changing the Switch Selectable Operation Modes

The following modes are selected by setting the on-board dip switches, Figure 20 at right shows where the switches are located on the operator control board. For each Operational Mode, the switches are set to either ON or OFF according to the table at right below. For all the modes, if an approved entrapment protection (EP) reversing device as described on page 3 of this manual is attached to the input labeled “Photo”, it will function as noted. Once an approved EP device is recognized by the control board it is monitored for correct operation. If the device becomes inactive then the mode will default to constant pressure activation for close regardless of the dip switch setting. In order for any of the Momentary Contact to Close operation modes (B2, TS, T) to become active an approved Entrapment Protection (EP) Reversing device (see Page 3) must be properly installed and connected to the operator. The switches must be set to one of the six Operational Mode combinations for the operator to function. In order for the NO (Normally Open) Reverse or NC (Normally Close) Reverse inputs to function, you must first install an operational approved Entrapment Protection (EP) Reversing Device.

B2 Operation (Factory Default)

Open Button: Momentary activation; open override of closing door.

Close Button: Momentary activation.

Stop Button: Momentary activation; stops open, close or reverse action.

Single Button: Momentary activation to open; open override of closing door, closes door from mid-stop or open limit.

EP Reverse (Photo Input): Momentary activation will reverse a closing door, reverse to full open (ignores mid-stop) unless stopped by stop pushbutton input.

Mid-Stop: Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position; if door is moving open, constant pressure on open button will bypass mid-stop.

Auto Close Timer: N/A.

C2 Operation

Open Button: Momentary activation; open override of closing door.

Close Button: Constant activation, door will stop when button is released.

Stop Button: Momentary activation; stops open, close or reverse action.

Single Button: Momentary activation to open; open override of closing door.

EP Reverse (Photo Input): Momentary activation will reverse a closing door, reverse to full open (ignores mid-stop) unless stopped by stop pushbutton input.

Mid-Stop: Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position; if door is moving open, constant pressure on open button will bypass mid-stop.

Auto Close Timer: N/A.

Settable

P4

Switches

Location

K5

K3

K4

K2

HIGH VOLTAGE

K6

P1

TR3

COM

CLS

OLS COM

STATUS

MO4

POWER

SW1

MO3

S4

MO2

P2

P3

LD2

S3

MO1

R89

R49

R10

R34 LD3

LD4

S2

ILK

TR1

R62

R22

R33

S1

OFF

24V

R47

C16

R23

R27

R83

R53

COM

R61

R51

C6

R9

R28

R46

R48

R19

R20

R82

R60

R45

C13

TR2

R17

R18

D3

C3

R5

R57

R25

R13

R14

R65

RADIO

C24

R1

R21

C10

C11

24V

D2

R52

RO1

D8

COM

C14

TR4

R31

C9

RM3

U1

RM2

EDGE

FRA

RM1

VCC

VCC

C30

P7

COM

S1

R85

C2

R38

R54

24V

R58

R11

R12

U4

R26

R29

R30

P6

R87

R55

C12

R15

R16

R94

C8

R56

Q1

R6

R7

R95

2005CDOMCB

CORP.ALLSTARc.p.

P5

R90

R84

R2

TSLKBREV112695PCB

C7

D1

R93

U5

R3

R8

R4

C25

C21

R24

PB1

PB2

PB3

C1

D12

OPEN

CLOSE

STOP

TB1

Figure 13

COM

24 VAC

ILOCK

SINGLE

COM

PHOTO

NC REV

NO REV

COM

STOP

CLOSE

OPEN

MOTOR CONTROL BOARD

Operating Mode	Switch 1	Switch 2	Switch 3	Switch 4
B2 Operation	ON	OFF	OFF	OFF
C2 Operation	OFF	OFF	OFF	OFF
D1 Operation	OFF	ON	OFF	OFF
E2 Operation	ON	ON	OFF	OFF
TS Operation	OFF	OFF	ON	OFF
T Operation	ON	OFF	ON	OFF

D1 Operation

Open Button: Constant activation; open override of closing door.

Close Button: Constant activation, door will stop when button is released.

Stop Button: Momentary activation; stops open, close or reverse action (not required).

Single Button: N/A.

EP Reverse (Photo Input): Momentary activation will stop a closing door.

Mid-Stop: Activation stops an opening door; after the door stops at the mid stop, constant contact of open button at mid stop will restart door to full open position.

Auto Close Timer: N/A.

E2 Operation (roll-back)

Open Button: Momentary activation; open override of closing door.

Close Button: Constant activation, door will reverse to full open (ignores mid-stop) when button is released.

Stop Button: Momentary activation; stops open, close or reverse action.

Single Button: N/A.

EP Reverse (Photo Input): Momentary activation to reverse a closing door, reverse to full open (ignores mid-stop) unless stopped by stop pushbutton input.