GE Monogram GXSF18G Connect to Electrical Power, Programming the Control, SET Present Time of DAY

Page 10

Installation Instructions

9 CONNECT TO ELECTRICAL POWER

To gain access to the transformer/power cord assembly, remove the salt hole cover from the softener. Unclip the tabs on the rear of the top cover and rotate the cover upward to remove. DO NOT PULL OR DISCONNECT WIRING.

•The softener works on 24 volt-60Hz electric power. The included transformer changes standard 120-volt AC house power to 24 volts.

Plug the transformer into a 120-volt outlet only. Be sure the outlet is always live so it can not be switched off by mistake.

•Replace the top cover.

•Replace the salt hole cover.

PROGRAMMING THE CONTROL

PROGRAMMING THE CONTROL

CONTROL SETTINGS REQUIRED upon installation and after an extended power outage.

NOTES:

•WHEN THE TRANSFORMER IS PLUGGED INTO THE ELECTRICAL OUTLET, 12:00 PM (flashing), and an arrow is displayed next to PRESENT TIME on the faceplate decal. The blue indicator light will also flash. Program the control as instructed below.

If - - - is flashing, use the UP button to set the correct F code as follows: F18 for

GXSF18G. If you pass by the correct code number, use the DOWN button. Then press the MODE button to accept the correct model.

•A “beep” sounds while pressing buttons for control programming. One beep signals a change in the control display. Repeated beeps mean the control will not accept a change from the button you have pressed, and you should select another button.

•To program the control, you will use the UP , DOWN and MODE buttons.

•Use the MODE button to scroll arrow to desired control function.

SET PRESENT TIME OF DAY

1. Press the MODE button SALT

 

until arrow points to

LEVEL

PM

 

PRESENT TIME.

 

 

2.Press UP or DOWN

button to set. The UP button advances the time; the DOWN button moves the time in reverse.

. If the present time is between noon and midnight, be sure PM shows in the display. If the present time is between midnight and noon, be sure AM shows in the display.

NOTE: Each press of an UP or DOWN button changes the time by one minute. Holding the button changes the time at a rapid rate.

3.When the present time is correct, press MODE to accept.

SET WATER HARDNESS NUMBER

1. Press the MODE button SALT

LEVEL

until arrow points to

HARDNESS.

2.Press UP or DOWN

button to set your water hardness number in the display. DOWN decreases the hardness value. UP increases the hardness value.

NOTE: Each press of a button changes the display by 1, between 1 and 25. Above 25, the display changes 5 at a time (25, 30, 35, etc.). Holding a button in changes the numbers at a rapid rate.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 7289396 215C1173P027 49-5018207-06 JR Safety InformationCare and Cleaning Write the model and serial numbers here Model #Safety Precautions Important Installation Recommendations Before Beginning InstallationRead these instructions completely and carefully Unpacking and Inspection Where to Install the SoftenerTransit Plan HOW YOU will Install the Softener OUTAdapter Install Bypass ValveBefore YOU Begin Valve body Bypass valve Inlet or outletConnect and RUN the Valve Drain Hose Plumb in and OUT Pipes to and from SoftenerFittings On valve Valve Connecting a Rigid Valve Drain TubeDrain Hose Tie or wire Hose in place 11⁄2″ air gapADD Water and Salt to the Brine Tank Install Grounding ClampWith salt SET Present Time of DAY Connect to Electrical PowerProgramming the Control SET Water Hardness NumberSET Recharge Starting Time SET Salt LevelDays to Empty Optional Control Settings Signals30″ Sanitizing ProceduresSPECIFICATIONS/DIMENSIONS 33⁄8″ Outlet Inlet 22.9″ 14.5″About the water softener system Breaking a Salt Bridge Cleaning the Nozzle and Venturi AssemblyGe.com Feature/Service Automatic Electronic Diagnostics Feature Optional Recharge ControlsFeature Memory Normal Operation, Control DisplaysTo remove an error code 1. Unplug transformer Service Timer/Softener, Service Checkout ProcedureERR Service Set Model Code Operation of DiagnosticsIf the water softening system does not draw brine, check Checking the Salt Storage Level and Refilling Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System However, you must keep the tank supplied with saltNo soft water Before you call for service…What To Do Taken not plumbed to soft waterExcessive/high level Water in brine tankBrown/yellow Brown/yellow colored Water after installationSalty tasting or Colored water Resin beads showingPage Ge.com Page Parts list Parts list Parts catalog General Electric Parts CatalogSupport Screen For The Period We Will Replace What Is Not CoveredWarrantor General Electric Company. Louisville, KY Warrantor Mabe Canada INC GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace One YearDe agua Cuidado y limpieza Cómo limpiar la ensambladuraDe averías Advertencia Advertencia No use con aguaRecomendaciones Importantes Para LA Instalación Lea estas instrucciones completa y cuidadosamenteHerramientas Y Materiales Necesarios Para LA Instalación Desempacado E InspecciónDonde Instalar EL Descalcificador Use la válvula de bypass incluida para instalarPlanifique LA Instalación DEL Descalcificador Ilustración DE Instalación NormalInstale LA Válvula DE Bypass Antes DE ComenzarRemueva el tapón plástico de embalaje y el cable de la Retire el descalcificador del lugar de instalación Cerciórese de cumplir con los códigos localesCont Salmuera Y LA MangueraCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Instale LA Abrazadera DE Tierra Cierre todos los grifos de aguaAjuste LA Hora DEL DÍA Conectar a LA Fuente EléctricaProgramación DEL Control Hora actualDe recarga Ajuste EL Nivel DE SALDías Hasta Vacío De salEficiencia DE LA SAL Ajustes Opcionales DE ControlSeñals En la fábrica se siguen los cuidados para mantener Procedimientos DE DesinfecciónNi infectarán su suministro de agua ni causarán que Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Función Memoria Operación normal, Pantalla de controlFunción Controles opcionales de recargado Característica/Servicio Diagnóstico electrónico automáticoVisualizado Servicio Diagnóstico electrónico iniciado manualmente Vea la sección Programación del controlServicio Configurar el código del modelo Servicio Inspección manual del avance de la recargaCuidado y limpieza del sistema de descalcificación de agua Cuándo rellenar con sal Si una luz indicadoraAntes de llamar para solicitar servicio… Qué hacerVeces el agua Luz intermitente azul Notas Lista de partes Ge.com Catálogo de partes Catálogo DE Partes DE General ElectricPASADOR, Expansión Por el período de Reemplazamos Garantía GE para el Sistema de Descalcificación de AguaLo que no está cubierto Garantías ampliadas Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Piezas y accesoriosConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio

GXSF18G specifications

The GE Monogram GXSF18G is a premium side-by-side refrigerator that combines sophisticated design with cutting-edge technology. This model is designed to meet the needs of modern households, blending style, functionality, and energy efficiency. It stands out with its sleek stainless steel finish and a professional look that elevates any kitchen decor.

One of the primary features of the GE Monogram GXSF18G is its spacious interior. With an impressive capacity, this refrigerator offers ample storage options for all your food items. The adjustable shelves allow for customization of the space, accommodating tall bottles or large containers with ease. The clear drawers provide easy visibility, ensuring that you can quickly find what you need without rummaging through the fridge.

The GXSF18G includes advanced cooling technologies that help maintain optimal temperature and humidity levels for food preservation. Its dual climate control system ensures separate temperature zones for the refrigerator and freezer. This innovation not only keeps your food fresher for longer but also helps reduce energy consumption, thus improving efficiency.

Another standout feature is the energy-efficient LED lighting, which illuminates the interior while consuming less power than traditional bulbs. This feature enhances visibility, making it easier to see everything inside and find items quickly, even in low light conditions.

The water and ice dispensing system is also noteworthy. It provides easy access to clean drinking water and ice without opening the refrigerator door, minimizing temperature fluctuations and maintaining freshness. The water filtration system is designed to reduce contaminants, ensuring you have access to pure, refreshing water.

Furthermore, the GE Monogram GXSF18G is equipped with smart technology, allowing you to monitor and manage settings right from your smartphone. This tech-savvy feature offers convenience for busy individuals, making it simple to keep track of your refrigerator's performance and any alerts that may arise.

In conclusion, the GE Monogram GXSF18G is a top-tier refrigerator that combines style, efficiency, and advanced technology. With its spacious interior, innovative cooling solutions, energy-saving features, and smart connectivity, it is an excellent choice for those looking to enhance their kitchen with a premium appliance that doesn't compromise on performance or design. Investing in this refrigerator means investing in quality and convenience for your home.
Top Page Image Contents