GE Monogram GXSF18G SET Salt Level, SET Recharge Starting Time, Days to Empty

Page 11
PM
DAYS TO EMPTY
SALT
LEVEL

Installation Instructions

SET WATER HARDNESS NUMBER (CONT.)

3.When the display shows your water hardness (in grains per gallon), press MODE to accept.

NOTE: If there is clear water iron in your water supply, you will need to increase the hardness setting by 5 for each 1 ppm of clear water iron in your water supply.

You can get the grains per gallon (gpg)

SET SALT LEVEL

1. Press the MODE button

SALT

until arrow

points to

LEVEL

 

SALT LEVEL.

2.Determine level of salt in

brine tank using yellow indicator on side of brine well, inside brine tank (see illustration on page 5).

3. Press UP or DOWN SALT

hardness of your water supply from a water analysis laboratory. If you are on a municipal

button to set the SALT LEVEL to correspond to

LEVEL

supply, call your local water department. Or call Legend Technical Services, an independent laboratory, to request a water hardness test kit at 1.800.949.8220, Option 4. If your report shows hardness in parts per million (ppm) or milligrams per liter (mg/l), simply divide by 17.1 to get the equivalent number of grains per gallon.

SET RECHARGE (STARTING) TIME

1. Press the MODE button LEVEL

AM

SALT

 

until arrow points to

 

 

RECHARGE TIME.

 

NOTE: A flashing 2:00 AM

(factory default) should show in the display. This is a good time for recharge to start (takes about 2 hours) in most households because water is not in use.

HARD WATER is bypassed to house faucets during recharge.

If no change is needed, go to step 3. To change the recharge starting time, follow step 2.

2.Press UP or DOWN button to set the desired recharge start time. Be sure to observe the AM or PM as you did when setting the time of day.

NOTE: Each press of a button changes the time by 1 hour. Holding the buttons in changes the time at a rapid rate.

3.Press the MODE button to accept.

level on yellow indicator in brine tank.

NOTE: Each press of a button changes the

level by increments of 0.5 up to 8.0. As the number increases, the salt level bars increase on each whole number. Lowering the salt level below zero turns the SALT LEVEL indicator OFF.

4. Press the MODE button to

 

 

 

 

 

SALT

 

 

accept. The display shows the

LEVEL

PM

 

 

 

 

 

 

 

 

DAYS TO EMPTY

 

present time of day and DAYS

 

 

 

E

 

TO EMPTY. RECHARGE TONIGHT

 

 

 

RECHARGE TONIGHT

 

 

 

 

 

 

 

 

 

 

 

 

 

may appear if unit is new.

 

 

 

 

 

 

 

 

 

 

DAYS TO EMPTY

The words DAYS TO EMPTY and a number are shown in the lower half of the display. This information is shown in the normal run display. This is to inform the user of the

number of days before the salt level in the brine tank reaches Level 0. There will be salt left in the salt tank, but it may not be sufficient to fully recharge the system. Salt should be added at this time to avoid hard water. The value is updated daily and whenever the SALT LEVEL value is changed.

NOTE: For the first several weeks of operation, the DAYS TO EMPTY may provide erratic operation. For example, the blue indicator light may flash, showing that more salt is required when the actual salt level in the tank is well above the Level 0. In some cases, the DAYS TO EMPTY may even increase over a several week period.

It takes a couple of months for the water softener to learn your water usage pattern. Once it does this, it will accurately determine actual salt usage pattern. During this first period, check salt level when blue indicator light flashes. If the salt level in the tank is at Level 1 or above, allow system to run. Be sure to reset your salt level indicator each time you add salt to the system.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Write the model and serial numbers here Model # Safety InformationCare and Cleaning 7289396 215C1173P027 49-5018207-06 JRSafety Precautions Read these instructions completely and carefully Before Beginning InstallationImportant Installation Recommendations Transit Where to Install the SoftenerUnpacking and Inspection OUT Plan HOW YOU will Install the SoftenerValve body Bypass valve Inlet or outlet Install Bypass ValveBefore YOU Begin AdapterPlumb in and OUT Pipes to and from Softener Connect and RUN the Valve Drain Hose11⁄2″ air gap Connecting a Rigid Valve Drain TubeDrain Hose Tie or wire Hose in place Fittings On valve ValveWith salt Install Grounding ClampADD Water and Salt to the Brine Tank SET Water Hardness Number Connect to Electrical PowerProgramming the Control SET Present Time of DAYDays to Empty SET Salt LevelSET Recharge Starting Time Signals Optional Control Settings33⁄8″ Outlet Inlet 22.9″ 14.5″ Sanitizing ProceduresSPECIFICATIONS/DIMENSIONS 30″About the water softener system Ge.com Cleaning the Nozzle and Venturi AssemblyBreaking a Salt Bridge Normal Operation, Control Displays Feature Optional Recharge ControlsFeature Memory Feature/Service Automatic Electronic DiagnosticsERR Service Timer/Softener, Service Checkout ProcedureTo remove an error code 1. Unplug transformer Operation of Diagnostics Service Set Model CodeIf the water softening system does not draw brine, check However, you must keep the tank supplied with salt Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System Checking the Salt Storage Level and RefillingTaken not plumbed to soft water Before you call for service…What To Do No soft waterWater in brine tank Excessive/high levelColored water Resin beads showing Brown/yellow colored Water after installationSalty tasting or Brown/yellowPage Ge.com Page Parts list Parts list General Electric Parts Catalog Parts catalogSupport Screen Warrantor General Electric Company. Louisville, KY What Is Not CoveredFor The Period We Will Replace One Year GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace Warrantor Mabe Canada INCDe averías Cómo limpiar la ensambladuraDe agua Cuidado y limpieza Advertencia No use con agua AdvertenciaLea estas instrucciones completa y cuidadosamente Recomendaciones Importantes Para LA InstalaciónUse la válvula de bypass incluida para instalar Desempacado E InspecciónDonde Instalar EL Descalcificador Herramientas Y Materiales Necesarios Para LA InstalaciónIlustración DE Instalación Normal Planifique LA Instalación DEL DescalcificadorRemueva el tapón plástico de embalaje y el cable de la Antes DE ComenzarInstale LA Válvula DE Bypass Cerciórese de cumplir con los códigos locales Retire el descalcificador del lugar de instalaciónCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Salmuera Y LA MangueraCont Cierre todos los grifos de agua Instale LA Abrazadera DE TierraHora actual Conectar a LA Fuente EléctricaProgramación DEL Control Ajuste LA Hora DEL DÍADe sal Ajuste EL Nivel DE SALDías Hasta Vacío De recargaSeñals Ajustes Opcionales DE ControlEficiencia DE LA SAL Ni infectarán su suministro de agua ni causarán que Procedimientos DE DesinfecciónEn la fábrica se siguen los cuidados para mantener Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Característica/Servicio Diagnóstico electrónico automático Operación normal, Pantalla de controlFunción Controles opcionales de recargado Función MemoriaVisualizado Vea la sección Programación del control Servicio Diagnóstico electrónico iniciado manualmenteServicio Inspección manual del avance de la recarga Servicio Configurar el código del modeloCuándo rellenar con sal Si una luz indicadora Cuidado y limpieza del sistema de descalcificación de aguaQué hacer Antes de llamar para solicitar servicio…Veces el agua Luz intermitente azul Notas Lista de partes Ge.com Catálogo DE Partes DE General Electric Catálogo de partesPASADOR, Expansión Lo que no está cubierto Garantía GE para el Sistema de Descalcificación de AguaPor el período de Reemplazamos Piezas y accesorios Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadasReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

GXSF18G specifications

The GE Monogram GXSF18G is a premium side-by-side refrigerator that combines sophisticated design with cutting-edge technology. This model is designed to meet the needs of modern households, blending style, functionality, and energy efficiency. It stands out with its sleek stainless steel finish and a professional look that elevates any kitchen decor.

One of the primary features of the GE Monogram GXSF18G is its spacious interior. With an impressive capacity, this refrigerator offers ample storage options for all your food items. The adjustable shelves allow for customization of the space, accommodating tall bottles or large containers with ease. The clear drawers provide easy visibility, ensuring that you can quickly find what you need without rummaging through the fridge.

The GXSF18G includes advanced cooling technologies that help maintain optimal temperature and humidity levels for food preservation. Its dual climate control system ensures separate temperature zones for the refrigerator and freezer. This innovation not only keeps your food fresher for longer but also helps reduce energy consumption, thus improving efficiency.

Another standout feature is the energy-efficient LED lighting, which illuminates the interior while consuming less power than traditional bulbs. This feature enhances visibility, making it easier to see everything inside and find items quickly, even in low light conditions.

The water and ice dispensing system is also noteworthy. It provides easy access to clean drinking water and ice without opening the refrigerator door, minimizing temperature fluctuations and maintaining freshness. The water filtration system is designed to reduce contaminants, ensuring you have access to pure, refreshing water.

Furthermore, the GE Monogram GXSF18G is equipped with smart technology, allowing you to monitor and manage settings right from your smartphone. This tech-savvy feature offers convenience for busy individuals, making it simple to keep track of your refrigerator's performance and any alerts that may arise.

In conclusion, the GE Monogram GXSF18G is a top-tier refrigerator that combines style, efficiency, and advanced technology. With its spacious interior, innovative cooling solutions, energy-saving features, and smart connectivity, it is an excellent choice for those looking to enhance their kitchen with a premium appliance that doesn't compromise on performance or design. Investing in this refrigerator means investing in quality and convenience for your home.
Top Page Image Contents