GE Monogram GXSF18G Before Beginning Installation, Important Installation Recommendations

Page 3

Installation Instructions

Water Softening System

Model GXSF18G

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com

WARNING: Read entire manual. Failure to follow all guides and rules could cause personal injury or property damage.

•Check with your state and/or local public works department for plumbing codes. You must follow their guides as you install the Water Softening system.

NOTE: Failure to comply with these installation instructions will void the product warranty, and the installer will be responsible for any service, repair or damages caused thereby.

BEFORE BEGINNING INSTALLATION

Read these instructions completely and carefully.

•IMPORTANT — Save these instructions for local inspector’s use.

•IMPORTANT — Observe all governing codes and ordinances.

•Note to Installer – Be sure to leave these instructions with the Consumer.

•Note to Consumer – Keep these instructions for future reference.

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not covered under the Warranty.

•A shutoff valve must be available or added near the installation point.

IMPORTANT INSTALLATION

RECOMMENDATIONS

•In the Commonwealth of Massachusetts, Plumbing Code 248 CMR shall be adhered to. Consult with your licensed plumber.

•Use only lead-free solder and flux for all sweat- solder connections, as required by state and federal codes.

•Connect the softener to the main water supply pipe before or ahead of the water heater.

DO NOT RUN HOT WATER THROUGH THE SOFTENER. Temperature of water passing through the softener must be less than 120°F.

IMPORTANT INSTALLATION

RECOMMENDATIONS (CONT.)

•Use care when handling the softener. Do not turn upside down, drop, drag or set on sharp protrusions.

•Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve if necessary. (Adding a pressure reducing valve may reduce the flow.)

•The softener works on 24 volt-60 Hz electrical power only. Be sure to use the included transformer. Be sure the electric outlet and transformer are in an inside location to protect from moisture.

•See Where to Install the Softener section for more details.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. The water should be tested periodically to verify that the system is performing satisfactorily.

•Small parts remaining after the installation could be a choke hazard. Discard safely.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Write the model and serial numbers here Model # Safety InformationCare and Cleaning 7289396 215C1173P027 49-5018207-06 JRSafety Precautions Before Beginning Installation Important Installation RecommendationsRead these instructions completely and carefully Where to Install the Softener Unpacking and InspectionTransit OUT Plan HOW YOU will Install the SoftenerValve body Bypass valve Inlet or outlet Install Bypass ValveBefore YOU Begin AdapterPlumb in and OUT Pipes to and from Softener Connect and RUN the Valve Drain Hose11⁄2″ air gap Connecting a Rigid Valve Drain TubeDrain Hose Tie or wire Hose in place Fittings On valve ValveInstall Grounding Clamp ADD Water and Salt to the Brine TankWith salt SET Water Hardness Number Connect to Electrical PowerProgramming the Control SET Present Time of DAYSET Salt Level SET Recharge Starting TimeDays to Empty Signals Optional Control Settings33⁄8″ Outlet Inlet 22.9″ 14.5″ Sanitizing ProceduresSPECIFICATIONS/DIMENSIONS 30″About the water softener system Cleaning the Nozzle and Venturi Assembly Breaking a Salt BridgeGe.com Normal Operation, Control Displays Feature Optional Recharge ControlsFeature Memory Feature/Service Automatic Electronic DiagnosticsService Timer/Softener, Service Checkout Procedure To remove an error code 1. Unplug transformerERR Operation of Diagnostics Service Set Model CodeIf the water softening system does not draw brine, check However, you must keep the tank supplied with salt Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System Checking the Salt Storage Level and RefillingTaken not plumbed to soft water Before you call for service…What To Do No soft waterWater in brine tank Excessive/high levelColored water Resin beads showing Brown/yellow colored Water after installationSalty tasting or Brown/yellowPage Ge.com Page Parts list Parts list General Electric Parts Catalog Parts catalogSupport Screen What Is Not Covered For The Period We Will ReplaceWarrantor General Electric Company. Louisville, KY One Year GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace Warrantor Mabe Canada INCCómo limpiar la ensambladura De agua Cuidado y limpiezaDe averías Advertencia No use con agua AdvertenciaLea estas instrucciones completa y cuidadosamente Recomendaciones Importantes Para LA InstalaciónUse la válvula de bypass incluida para instalar Desempacado E InspecciónDonde Instalar EL Descalcificador Herramientas Y Materiales Necesarios Para LA InstalaciónIlustración DE Instalación Normal Planifique LA Instalación DEL DescalcificadorAntes DE Comenzar Instale LA Válvula DE BypassRemueva el tapón plástico de embalaje y el cable de la Cerciórese de cumplir con los códigos locales Retire el descalcificador del lugar de instalaciónSalmuera Y LA Manguera ContCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Cierre todos los grifos de agua Instale LA Abrazadera DE TierraHora actual Conectar a LA Fuente EléctricaProgramación DEL Control Ajuste LA Hora DEL DÍADe sal Ajuste EL Nivel DE SALDías Hasta Vacío De recargaAjustes Opcionales DE Control Eficiencia DE LA SALSeñals Procedimientos DE Desinfección En la fábrica se siguen los cuidados para mantenerNi infectarán su suministro de agua ni causarán que Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Característica/Servicio Diagnóstico electrónico automático Operación normal, Pantalla de controlFunción Controles opcionales de recargado Función MemoriaVisualizado Vea la sección Programación del control Servicio Diagnóstico electrónico iniciado manualmenteServicio Inspección manual del avance de la recarga Servicio Configurar el código del modeloCuándo rellenar con sal Si una luz indicadora Cuidado y limpieza del sistema de descalcificación de aguaQué hacer Antes de llamar para solicitar servicio…Veces el agua Luz intermitente azul Notas Lista de partes Ge.com Catálogo DE Partes DE General Electric Catálogo de partesPASADOR, Expansión Garantía GE para el Sistema de Descalcificación de Agua Por el período de ReemplazamosLo que no está cubierto Piezas y accesorios Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadasReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

GXSF18G specifications

The GE Monogram GXSF18G is a premium side-by-side refrigerator that combines sophisticated design with cutting-edge technology. This model is designed to meet the needs of modern households, blending style, functionality, and energy efficiency. It stands out with its sleek stainless steel finish and a professional look that elevates any kitchen decor.

One of the primary features of the GE Monogram GXSF18G is its spacious interior. With an impressive capacity, this refrigerator offers ample storage options for all your food items. The adjustable shelves allow for customization of the space, accommodating tall bottles or large containers with ease. The clear drawers provide easy visibility, ensuring that you can quickly find what you need without rummaging through the fridge.

The GXSF18G includes advanced cooling technologies that help maintain optimal temperature and humidity levels for food preservation. Its dual climate control system ensures separate temperature zones for the refrigerator and freezer. This innovation not only keeps your food fresher for longer but also helps reduce energy consumption, thus improving efficiency.

Another standout feature is the energy-efficient LED lighting, which illuminates the interior while consuming less power than traditional bulbs. This feature enhances visibility, making it easier to see everything inside and find items quickly, even in low light conditions.

The water and ice dispensing system is also noteworthy. It provides easy access to clean drinking water and ice without opening the refrigerator door, minimizing temperature fluctuations and maintaining freshness. The water filtration system is designed to reduce contaminants, ensuring you have access to pure, refreshing water.

Furthermore, the GE Monogram GXSF18G is equipped with smart technology, allowing you to monitor and manage settings right from your smartphone. This tech-savvy feature offers convenience for busy individuals, making it simple to keep track of your refrigerator's performance and any alerts that may arise.

In conclusion, the GE Monogram GXSF18G is a top-tier refrigerator that combines style, efficiency, and advanced technology. With its spacious interior, innovative cooling solutions, energy-saving features, and smart connectivity, it is an excellent choice for those looking to enhance their kitchen with a premium appliance that doesn't compromise on performance or design. Investing in this refrigerator means investing in quality and convenience for your home.
Top Page Image Contents