GE Monogram GXSF18G Connecting a Rigid Valve Drain Tube, Fittings On valve Valve, 11⁄2″ air gap

Page 8

Installation Instructions

4CONNECT AND RUN THE VALVE DRAIN HOSE (CONT.)

•Elevating the drain hose may cause back pressure that could reduce the brine draw during recharge. If raising the drain line overhead is required to get to the drain point, measure the inlet water pressure to the softener first. For inlet

pressures between 20 and 50 psi, do not raise higher than 8′ above the floor. For inlet pressure

above 50 psi, the drain line may be raised to a maximum height of 14′.

Drain

Clamp

STANDPIPE

fittings

 

on valve

 

Valve

LAUNDRY TUB

 

drain

 

hose

Tie or wire

 

hose in place

 

SUMP

 

11⁄2″ air gap

 

FLOOR

 

DRAIN

CONNECTING A RIGID VALVE DRAIN TUBE

To adapt a copper drain tube to the softener, use a hacksaw to cut the barbed end from the drain fitting as shown. Rotate the drain fitting so the cutting blade clears the valve housing to prevent damage to valve. Buy a compression fitting (1/4″ female pipe thread x 1/2″ O.D. tube) and needed tubing from your local hardware store.

1/4″ NPT threads

Barbs ″

1/2 O.D. copper tube (not provided)

Clip

Cut barbs from drain fitting

Compression fitting 1/4″ NPT x 1/2″ O.D. tube (not provided)

5INSTALL THE BRINE TANK OVERFLOW FITTINGS AND HOSE

•Insert the rubber grommet into the 3/4″ diameter hole in the brine tank sidewall as shown.

•Push the end of the hose adapter elbow into the grommet as shown.

•Attach a length of hose (use remaining hose from Step 4) to the hose adapter elbow. Use a hose clamp to hold it in place.

•Locate the other end of the hose at the drain point. DO NOT ELEVATE this hose higher than the elbow on the brine tank.

IMPORTANT: DO NOT TEE OVERFLOW HOSE TO VALVE DRAIN HOSE.

NOTE: This drain is for safety only. If the cabinet (brine tank) should over-fill with water, the excess is carried to the drain.

Hose

adapter

Hose

Grommet clamp

Do not connect

to valve drain

Overflow hose. drain hose

To acceptable drain

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Safety Information Care and Cleaning7289396 215C1173P027 49-5018207-06 JR Write the model and serial numbers here Model #Safety Precautions Read these instructions completely and carefully Before Beginning InstallationImportant Installation Recommendations Transit Where to Install the SoftenerUnpacking and Inspection Plan HOW YOU will Install the Softener OUTInstall Bypass Valve Before YOU BeginAdapter Valve body Bypass valve Inlet or outletConnect and RUN the Valve Drain Hose Plumb in and OUT Pipes to and from SoftenerConnecting a Rigid Valve Drain Tube Drain Hose Tie or wire Hose in placeFittings On valve Valve 11⁄2″ air gapWith salt Install Grounding ClampADD Water and Salt to the Brine Tank Connect to Electrical Power Programming the ControlSET Present Time of DAY SET Water Hardness NumberDays to Empty SET Salt LevelSET Recharge Starting Time Optional Control Settings SignalsSanitizing Procedures SPECIFICATIONS/DIMENSIONS30″ 33⁄8″ Outlet Inlet 22.9″ 14.5″About the water softener system Ge.com Cleaning the Nozzle and Venturi AssemblyBreaking a Salt Bridge Feature Optional Recharge Controls Feature MemoryFeature/Service Automatic Electronic Diagnostics Normal Operation, Control DisplaysERR Service Timer/Softener, Service Checkout ProcedureTo remove an error code 1. Unplug transformer Service Set Model Code Operation of DiagnosticsIf the water softening system does not draw brine, check Care and cleaning of the water softening system Cleaning Iron Out of the Water Softening SystemChecking the Salt Storage Level and Refilling However, you must keep the tank supplied with saltBefore you call for service… What To DoNo soft water Taken not plumbed to soft waterExcessive/high level Water in brine tankBrown/yellow colored Water after installation Salty tasting orBrown/yellow Colored water Resin beads showingPage Ge.com Page Parts list Parts list Parts catalog General Electric Parts CatalogSupport Screen Warrantor General Electric Company. Louisville, KY What Is Not CoveredFor The Period We Will Replace GE Water Softening System Warranty. For Customers in Canada For The Period Of We Will ReplaceWarrantor Mabe Canada INC One YearDe averías Cómo limpiar la ensambladuraDe agua Cuidado y limpieza Advertencia Advertencia No use con aguaRecomendaciones Importantes Para LA Instalación Lea estas instrucciones completa y cuidadosamenteDesempacado E Inspección Donde Instalar EL DescalcificadorHerramientas Y Materiales Necesarios Para LA Instalación Use la válvula de bypass incluida para instalarPlanifique LA Instalación DEL Descalcificador Ilustración DE Instalación NormalRemueva el tapón plástico de embalaje y el cable de la Antes DE ComenzarInstale LA Válvula DE Bypass Retire el descalcificador del lugar de instalación Cerciórese de cumplir con los códigos localesCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Salmuera Y LA MangueraCont Instale LA Abrazadera DE Tierra Cierre todos los grifos de aguaConectar a LA Fuente Eléctrica Programación DEL ControlAjuste LA Hora DEL DÍA Hora actualAjuste EL Nivel DE SAL Días Hasta VacíoDe recarga De salSeñals Ajustes Opcionales DE ControlEficiencia DE LA SAL Ni infectarán su suministro de agua ni causarán que Procedimientos DE DesinfecciónEn la fábrica se siguen los cuidados para mantener Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Operación normal, Pantalla de control Función Controles opcionales de recargadoFunción Memoria Característica/Servicio Diagnóstico electrónico automáticoVisualizado Servicio Diagnóstico electrónico iniciado manualmente Vea la sección Programación del controlServicio Configurar el código del modelo Servicio Inspección manual del avance de la recargaCuidado y limpieza del sistema de descalcificación de agua Cuándo rellenar con sal Si una luz indicadoraAntes de llamar para solicitar servicio… Qué hacerVeces el agua Luz intermitente azul Notas Lista de partes Ge.com Catálogo de partes Catálogo DE Partes DE General ElectricPASADOR, Expansión Lo que no está cubierto Garantía GE para el Sistema de Descalcificación de AguaPor el período de Reemplazamos Soporte al Consumidor Página Web de GE Appliances Solicite una reparaciónGarantías ampliadas Piezas y accesoriosSchedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio

GXSF18G specifications

The GE Monogram GXSF18G is a premium side-by-side refrigerator that combines sophisticated design with cutting-edge technology. This model is designed to meet the needs of modern households, blending style, functionality, and energy efficiency. It stands out with its sleek stainless steel finish and a professional look that elevates any kitchen decor.

One of the primary features of the GE Monogram GXSF18G is its spacious interior. With an impressive capacity, this refrigerator offers ample storage options for all your food items. The adjustable shelves allow for customization of the space, accommodating tall bottles or large containers with ease. The clear drawers provide easy visibility, ensuring that you can quickly find what you need without rummaging through the fridge.

The GXSF18G includes advanced cooling technologies that help maintain optimal temperature and humidity levels for food preservation. Its dual climate control system ensures separate temperature zones for the refrigerator and freezer. This innovation not only keeps your food fresher for longer but also helps reduce energy consumption, thus improving efficiency.

Another standout feature is the energy-efficient LED lighting, which illuminates the interior while consuming less power than traditional bulbs. This feature enhances visibility, making it easier to see everything inside and find items quickly, even in low light conditions.

The water and ice dispensing system is also noteworthy. It provides easy access to clean drinking water and ice without opening the refrigerator door, minimizing temperature fluctuations and maintaining freshness. The water filtration system is designed to reduce contaminants, ensuring you have access to pure, refreshing water.

Furthermore, the GE Monogram GXSF18G is equipped with smart technology, allowing you to monitor and manage settings right from your smartphone. This tech-savvy feature offers convenience for busy individuals, making it simple to keep track of your refrigerator's performance and any alerts that may arise.

In conclusion, the GE Monogram GXSF18G is a top-tier refrigerator that combines style, efficiency, and advanced technology. With its spacious interior, innovative cooling solutions, energy-saving features, and smart connectivity, it is an excellent choice for those looking to enhance their kitchen with a premium appliance that doesn't compromise on performance or design. Investing in this refrigerator means investing in quality and convenience for your home.
Top Page Image Contents