GE Monogram GXSF18G If the water softening system does not draw brine, check

Page 19

ge.com

Service: Manually Advance Recharge Check

NOTE: The control display must show a steady time (not flashing).

1.Press the RECHARGE button and hold in for three seconds. RECHARGE begins to flash as the water softening system enters the fill cycle of recharge. Remove the brinewell cover and, using a flashlight, observe fill water entering the brine tank. If water does not enter the tank, look for an obstructed nozzle, venturi, fill flow plug or brine tubing. See Care and Cleaning of the Water Softener System section.

2.After observing fill, press the RECHARGE button to move the water softening system into brining. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level over an extended period of time.

NOTE: Be sure a salt bridge is not preventing water from contacting salt. See Care and cleaning of the water softening system section.

If the water softening system does not draw brine, check:

■nozzle and/or venturi dirty or defective.

■defective nozzle and venturi seal.

■nozzle and venturi not seated properly on gasket.

■other inner valve defect (rotor seal, rotor and disc, wave washer, etc.).

■restricted drain (check drain fitting and hose).

NOTE: If water system pressure is low, an elevated drain hose may cause back pressure, stopping brine draw.

3.Again, press the RECHARGE button to move the water softening system into backwash. Look for a fast flow of water from the drain hose. A slow flow indicates a plugged top distributor, backwash flow plug or drain hose.

4.Press the RECHARGE button to move the water softening system into fast rinse. Again look for a fast drain flow. Allow the water softening system to rinse for a few minutes to flush out any brine that may remain in the resin tank from the brining cycle test.

5.To return the water softening system to service, press the RECHARGE button.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Write the model and serial numbers here Model # Safety InformationCare and Cleaning 7289396 215C1173P027 49-5018207-06 JRSafety Precautions Important Installation Recommendations Before Beginning InstallationRead these instructions completely and carefully Unpacking and Inspection Where to Install the SoftenerTransit OUT Plan HOW YOU will Install the SoftenerValve body Bypass valve Inlet or outlet Install Bypass ValveBefore YOU Begin AdapterPlumb in and OUT Pipes to and from Softener Connect and RUN the Valve Drain Hose11⁄2″ air gap Connecting a Rigid Valve Drain TubeDrain Hose Tie or wire Hose in place Fittings On valve ValveADD Water and Salt to the Brine Tank Install Grounding ClampWith salt SET Water Hardness Number Connect to Electrical PowerProgramming the Control SET Present Time of DAYSET Recharge Starting Time SET Salt LevelDays to Empty Signals Optional Control Settings33⁄8″ Outlet Inlet 22.9″ 14.5″ Sanitizing ProceduresSPECIFICATIONS/DIMENSIONS 30″About the water softener system Breaking a Salt Bridge Cleaning the Nozzle and Venturi AssemblyGe.com Normal Operation, Control Displays Feature Optional Recharge ControlsFeature Memory Feature/Service Automatic Electronic DiagnosticsTo remove an error code 1. Unplug transformer Service Timer/Softener, Service Checkout ProcedureERR Operation of Diagnostics Service Set Model CodeIf the water softening system does not draw brine, check However, you must keep the tank supplied with salt Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System Checking the Salt Storage Level and RefillingTaken not plumbed to soft water Before you call for service…What To Do No soft waterWater in brine tank Excessive/high levelColored water Resin beads showing Brown/yellow colored Water after installationSalty tasting or Brown/yellowPage Ge.com Page Parts list Parts list General Electric Parts Catalog Parts catalogSupport Screen For The Period We Will Replace What Is Not CoveredWarrantor General Electric Company. Louisville, KY One Year GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace Warrantor Mabe Canada INCDe agua Cuidado y limpieza Cómo limpiar la ensambladuraDe averías Advertencia No use con agua AdvertenciaLea estas instrucciones completa y cuidadosamente Recomendaciones Importantes Para LA InstalaciónUse la válvula de bypass incluida para instalar Desempacado E InspecciónDonde Instalar EL Descalcificador Herramientas Y Materiales Necesarios Para LA InstalaciónIlustración DE Instalación Normal Planifique LA Instalación DEL DescalcificadorInstale LA Válvula DE Bypass Antes DE ComenzarRemueva el tapón plástico de embalaje y el cable de la Cerciórese de cumplir con los códigos locales Retire el descalcificador del lugar de instalaciónCont Salmuera Y LA MangueraCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Cierre todos los grifos de agua Instale LA Abrazadera DE TierraHora actual Conectar a LA Fuente EléctricaProgramación DEL Control Ajuste LA Hora DEL DÍADe sal Ajuste EL Nivel DE SALDías Hasta Vacío De recargaEficiencia DE LA SAL Ajustes Opcionales DE ControlSeñals En la fábrica se siguen los cuidados para mantener Procedimientos DE DesinfecciónNi infectarán su suministro de agua ni causarán que Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Característica/Servicio Diagnóstico electrónico automático Operación normal, Pantalla de controlFunción Controles opcionales de recargado Función MemoriaVisualizado Vea la sección Programación del control Servicio Diagnóstico electrónico iniciado manualmenteServicio Inspección manual del avance de la recarga Servicio Configurar el código del modeloCuándo rellenar con sal Si una luz indicadora Cuidado y limpieza del sistema de descalcificación de aguaQué hacer Antes de llamar para solicitar servicio…Veces el agua Luz intermitente azul Notas Lista de partes Ge.com Catálogo DE Partes DE General Electric Catálogo de partesPASADOR, Expansión Por el período de Reemplazamos Garantía GE para el Sistema de Descalcificación de AguaLo que no está cubierto Piezas y accesorios Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Garantías ampliadasReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

GXSF18G specifications

The GE Monogram GXSF18G is a premium side-by-side refrigerator that combines sophisticated design with cutting-edge technology. This model is designed to meet the needs of modern households, blending style, functionality, and energy efficiency. It stands out with its sleek stainless steel finish and a professional look that elevates any kitchen decor.

One of the primary features of the GE Monogram GXSF18G is its spacious interior. With an impressive capacity, this refrigerator offers ample storage options for all your food items. The adjustable shelves allow for customization of the space, accommodating tall bottles or large containers with ease. The clear drawers provide easy visibility, ensuring that you can quickly find what you need without rummaging through the fridge.

The GXSF18G includes advanced cooling technologies that help maintain optimal temperature and humidity levels for food preservation. Its dual climate control system ensures separate temperature zones for the refrigerator and freezer. This innovation not only keeps your food fresher for longer but also helps reduce energy consumption, thus improving efficiency.

Another standout feature is the energy-efficient LED lighting, which illuminates the interior while consuming less power than traditional bulbs. This feature enhances visibility, making it easier to see everything inside and find items quickly, even in low light conditions.

The water and ice dispensing system is also noteworthy. It provides easy access to clean drinking water and ice without opening the refrigerator door, minimizing temperature fluctuations and maintaining freshness. The water filtration system is designed to reduce contaminants, ensuring you have access to pure, refreshing water.

Furthermore, the GE Monogram GXSF18G is equipped with smart technology, allowing you to monitor and manage settings right from your smartphone. This tech-savvy feature offers convenience for busy individuals, making it simple to keep track of your refrigerator's performance and any alerts that may arise.

In conclusion, the GE Monogram GXSF18G is a top-tier refrigerator that combines style, efficiency, and advanced technology. With its spacious interior, innovative cooling solutions, energy-saving features, and smart connectivity, it is an excellent choice for those looking to enhance their kitchen with a premium appliance that doesn't compromise on performance or design. Investing in this refrigerator means investing in quality and convenience for your home.
Top Page Image Contents