GE Monogram GXSF18G Before YOU Begin, Install Bypass Valve, Adapter, Push all the way

Page 6

Installation Instructions

BEFORE YOU BEGIN

Turn off the gas or electric supply to the water heater, in the possibility that the water heater may be drained while draining pipes.

Turn off the water supply to pipes to be cut and drain the house water pipes.

Open both hot and cold faucets at the lowest location possible.

NOTE: For easier installation, remove the top cover. Slide the salt hole cover open. Locate the top cover release point. Pull gently on the top cover at the release point, lift up and rotate top cover backward to remove.

Top

Salt Hole

Cover

Cover

Release

 

Point

Top

 

Cover

Remove all packing material located under top cover.

1INSTALL BYPASS VALVE

Remove plastic shipping plug and wire from valve

outlet.Turbine

Valve outlet

Turbine shaft and support

NOTE: Be sure the turbine and support are firmly in place in the valve outlet. Blow into the valve port and observe the turbine for free rotation.

Push the bypass valve (lubricate o-ring seals with silicone grease) into both ports of the valve as shown.

Clips

 

Outlet

NPT

 

adapter

Drain fitting

Clip

 

Inlet

Bypass

O-rings

valve

 

O-ring seal goes into the outer groove only. The clip snaps into the inner groove (see below).

Snap the 2 large plastic clips in place, from the top down, as shown.

SIDE

Clip

VIEW

END

 

VIEW

Valve body

Bypass valve

inlet or outlet

(push all the way in)

Push the NPT adapters (lubricate o-ring seals with silicone grease) into both ports of the valve as shown.

Snap the 2 large plastic clips in place, from the side, as shown.

2MOVE THE SOFTENER ASSEMBLY INTO INSTALLATION POSITION

Before sliding softener in position, be sure the installation surface is level and smooth. Sharp objects under the tank may puncture it. If needed, place the tank on a section of 3/4thick (minimum) plywood. Then, place shims under the plywood as needed to level the softener. Slide softener into position.

6

Image 6
Contents 7289396 215C1173P027 49-5018207-06 JR Safety InformationCare and Cleaning Write the model and serial numbers here Model #Safety Precautions Before Beginning Installation Important Installation RecommendationsRead these instructions completely and carefully Where to Install the Softener Unpacking and InspectionTransit Plan HOW YOU will Install the Softener OUTAdapter Install Bypass ValveBefore YOU Begin Valve body Bypass valve Inlet or outletConnect and RUN the Valve Drain Hose Plumb in and OUT Pipes to and from SoftenerFittings On valve Valve Connecting a Rigid Valve Drain TubeDrain Hose Tie or wire Hose in place 11⁄2″ air gapInstall Grounding Clamp ADD Water and Salt to the Brine TankWith salt SET Present Time of DAY Connect to Electrical PowerProgramming the Control SET Water Hardness NumberSET Salt Level SET Recharge Starting TimeDays to Empty Optional Control Settings Signals30″ Sanitizing ProceduresSPECIFICATIONS/DIMENSIONS 33⁄8″ Outlet Inlet 22.9″ 14.5″About the water softener system Cleaning the Nozzle and Venturi Assembly Breaking a Salt BridgeGe.com Feature/Service Automatic Electronic Diagnostics Feature Optional Recharge ControlsFeature Memory Normal Operation, Control DisplaysService Timer/Softener, Service Checkout Procedure To remove an error code 1. Unplug transformerERR Service Set Model Code Operation of DiagnosticsIf the water softening system does not draw brine, check Checking the Salt Storage Level and Refilling Care and cleaning of the water softening systemCleaning Iron Out of the Water Softening System However, you must keep the tank supplied with saltNo soft water Before you call for service…What To Do Taken not plumbed to soft waterExcessive/high level Water in brine tankBrown/yellow Brown/yellow colored Water after installationSalty tasting or Colored water Resin beads showingPage Ge.com Page Parts list Parts list Parts catalog General Electric Parts CatalogSupport Screen What Is Not Covered For The Period We Will ReplaceWarrantor General Electric Company. Louisville, KY Warrantor Mabe Canada INC GE Water Softening System Warranty. For Customers in CanadaFor The Period Of We Will Replace One YearCómo limpiar la ensambladura De agua Cuidado y limpiezaDe averías Advertencia Advertencia No use con aguaRecomendaciones Importantes Para LA Instalación Lea estas instrucciones completa y cuidadosamenteHerramientas Y Materiales Necesarios Para LA Instalación Desempacado E InspecciónDonde Instalar EL Descalcificador Use la válvula de bypass incluida para instalarPlanifique LA Instalación DEL Descalcificador Ilustración DE Instalación NormalAntes DE Comenzar Instale LA Válvula DE BypassRemueva el tapón plástico de embalaje y el cable de la Retire el descalcificador del lugar de instalación Cerciórese de cumplir con los códigos localesSalmuera Y LA Manguera ContCómo Conectar UN Tubo DE Drenaje DE Válvula Rígida Instale LA Abrazadera DE Tierra Cierre todos los grifos de aguaAjuste LA Hora DEL DÍA Conectar a LA Fuente EléctricaProgramación DEL Control Hora actualDe recarga Ajuste EL Nivel DE SALDías Hasta Vacío De salAjustes Opcionales DE Control Eficiencia DE LA SALSeñals Procedimientos DE Desinfección En la fábrica se siguen los cuidados para mantenerNi infectarán su suministro de agua ni causarán que Sobre el sistema de descalcificación de agua Cómo romper un puente de sal Cómo limpiar la ensambladura de la boquilla y el Venturi Función Memoria Operación normal, Pantalla de controlFunción Controles opcionales de recargado Característica/Servicio Diagnóstico electrónico automáticoVisualizado Servicio Diagnóstico electrónico iniciado manualmente Vea la sección Programación del controlServicio Configurar el código del modelo Servicio Inspección manual del avance de la recargaCuidado y limpieza del sistema de descalcificación de agua Cuándo rellenar con sal Si una luz indicadoraAntes de llamar para solicitar servicio… Qué hacerVeces el agua Luz intermitente azul Notas Lista de partes Ge.com Catálogo de partes Catálogo DE Partes DE General ElectricPASADOR, Expansión Garantía GE para el Sistema de Descalcificación de Agua Por el período de ReemplazamosLo que no está cubierto Garantías ampliadas Soporte al Consumidor Página Web de GE AppliancesSolicite una reparación Piezas y accesoriosConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio

GXSF18G specifications

The GE Monogram GXSF18G is a premium side-by-side refrigerator that combines sophisticated design with cutting-edge technology. This model is designed to meet the needs of modern households, blending style, functionality, and energy efficiency. It stands out with its sleek stainless steel finish and a professional look that elevates any kitchen decor.

One of the primary features of the GE Monogram GXSF18G is its spacious interior. With an impressive capacity, this refrigerator offers ample storage options for all your food items. The adjustable shelves allow for customization of the space, accommodating tall bottles or large containers with ease. The clear drawers provide easy visibility, ensuring that you can quickly find what you need without rummaging through the fridge.

The GXSF18G includes advanced cooling technologies that help maintain optimal temperature and humidity levels for food preservation. Its dual climate control system ensures separate temperature zones for the refrigerator and freezer. This innovation not only keeps your food fresher for longer but also helps reduce energy consumption, thus improving efficiency.

Another standout feature is the energy-efficient LED lighting, which illuminates the interior while consuming less power than traditional bulbs. This feature enhances visibility, making it easier to see everything inside and find items quickly, even in low light conditions.

The water and ice dispensing system is also noteworthy. It provides easy access to clean drinking water and ice without opening the refrigerator door, minimizing temperature fluctuations and maintaining freshness. The water filtration system is designed to reduce contaminants, ensuring you have access to pure, refreshing water.

Furthermore, the GE Monogram GXSF18G is equipped with smart technology, allowing you to monitor and manage settings right from your smartphone. This tech-savvy feature offers convenience for busy individuals, making it simple to keep track of your refrigerator's performance and any alerts that may arise.

In conclusion, the GE Monogram GXSF18G is a top-tier refrigerator that combines style, efficiency, and advanced technology. With its spacious interior, innovative cooling solutions, energy-saving features, and smart connectivity, it is an excellent choice for those looking to enhance their kitchen with a premium appliance that doesn't compromise on performance or design. Investing in this refrigerator means investing in quality and convenience for your home.