Harman-Kardon AVR 160 Step Eight Program Sources Into the Remote, Step Nine Turn On the AVR

Page 22

INSTALLATION

STEP EIGHT – Program Sources Into the Remote

The AVR 160 remote may be programmed to control many brands and models of DVD players, cable boxes, satellite receivers, the Harman Kardon DMC 1000 digital media center and TVs.

To access the functions for a particular device, switch the remote’s device mode. Press the AVR Button to access the codes that control the receiver, or the Source Selector Buttons to access the codes for the devices programmed into the remote.

While the DVD Source Selector may be used to operate either a Harman Kardon Blu-ray Disc player or a DVD player, the default mode is to operate a Harman Kardon Blu-ray Disc player. To toggle between Harman Kardon Blu-ray Disc player and DVD player operation, press and hold the DVD Source Selector for 2 seconds. The source selector will flash twice to confirm that the remote’s mode has changed to operate the other type of disc player.

NOTE: The remote may be easily programmed to operate the Harman Kardon DVD players using the Video 1 or any of the HDMI Input Selectors, by following the instructions below. Select the VCR/PVR/DMC device type in number 4. Enter code 002.

If you have other source devices in your system, follow these steps to program the correct codes into the remote.

1.Using the codes in Tables A11–A17 of the Appendix, look up the product type (e.g., DVD, cable TV box) and the brand name of your source. The number(s) listed is/are potential candidates for the correct code set for your particular device.

2.Turn on your source device.

3.This step places the remote in program mode. Press and hold the Source Selector until the Program Indicator LED on the remote starts to flash, then release it. When pressed, the Source Selector will light red briefly, go dark, and then relight when the Program Indicator LED starts to flash.

4.Program the desired device type for any of the three HDMI selectors by pressing the corresponding Source Selector:

• Press DVD to operate a DVD player.

• Press VID1 to operate a VCR or PVR, or a Harman Kardon digital media center.

• Press VID2 to operate a cable or satellite set-top box.

5.Enter a code from number 1 above.

a)If the device turns off, then press the Source Selector again to accept the code; it will flash. The remote will exit the Program mode.

b)If the device does not turn off, try entering another code. If you run out of codes, you may search through all of the codes in the remote’s library for that product type by pressing the K or L Button repeatedly until the device turns off. When the device turns off, enter the code by pressing the Source Selector; it will flash. The remote then exits Program mode.

6.Once you have programmed a code, try using some other functions to control the device. Sometimes manufacturers use the same Power code for several different models, while other codes vary. Repeat this process until you’ve programmed a satisfactory code set that operates most of the functions you frequently use.

7.Find out which code number you have programmed by pressing and holding the Source Selector to enter the Program mode. Press the OK Button, and the Program Indicator LED will flash in the code sequence. One flash represents “1”, two flashes for “2”, and so forth. A series of many fast flashes represents “0”. Record the codes programmed for each device in Table A7 in the Appendix.

If you are unable to locate a code set that correctly operates your source device, it will not be possible to use the AVR remote to control that device. You may still connect the source to the AVR 160 and operate it using the device’s original remote control.

Most of the button labels on the remote describe the button’s function when used to control the AVR 160. However, the button may perform a very different function when used to control another device. Refer to the Remote Control Function List, Table A10 in the Appendix, for each button’s functions with the various product types.

You may program Macros, which are preprogrammed code sequences that execute many code commands with a single button press. You may also program “punch-through” codes, which allow the remote to operate the volume, channel or transport controls of another device without having to switch the remote’s device mode. See pages 35 through 36 for instructions on these advanced programming functions.

Note: The AVR 160 remote is preprogrammed to operate the transport controls of Harman Kardon Blu-ray Disc or DVD players when the AVR or the Video 2 (cable/satellite) or Video 3 (TV) source is selected. You may change this punch-through programming at any time.

STEP NINE – Turn On the AVR 160

Two steps are required the first time you turn on the AVR 160.

1.Flip the rear-panel Main Power Switch to the “On” position. The Power Indicator on the front panel will turn amber, indicating that the AVR is in Standby mode and is ready to be turned on. Normally, you may leave the Main Power Switch on, even when the receiver is not being used.

2.There are several ways to turn on the AVR from Standby mode.

a)Press the Standby/On Switch on the front panel.

b)Using the remote, press the AVR Power On Button or any of the Source Selectors.

NOTES:

• Any time you press one of the Source Selectors on the remote, the remote will switch device modes. To control the receiver, press the AVR Button.

• If you do not see a picture within about 1 minute, refer to the Video Troubleshooting Tips on page 27.

22

Image 22
Contents AVR Important Safety Instructions Safety InformationImportant Safety Information Do Not Open the Cabinet Installation LocationCleaning Moving the UnitTable of Contents Harman Kardon AVR 160 7.1-Channel Audio/ Video Receiver IntroductionThank you for choosing a Harman Kardon product Audio SectionAudio/Video Inputs Supplied AccessoriesAudio Inputs Digital Audio InputsTuning Press these buttons to tune a radio station FRONT-PANEL ControlsVolume Knob Turn this knob to raise or lower the volume Use an HDMI-to-DVI adapter REAR-PANEL ConnectionsAlways make a separate audio connection REAR-PANEL Connections Remote Control Functions AM/FMAVR Selector Press to switch the remote to AVR device mode AUX Controls a device connected to the Auxiliary InputRDS Activates RDS functions for FM Radio Multichannel Audio Introduction to Home TheaterTypical Home Theater System Surround ModesSpeaker Connections Connecting Source Devices to the AVRConnections SubwooferDigital Audio Analog AudioDigital Video AntennasVideo Connections Analog VideoPlacement of Surround Speakers in a 5.1- Channel System Speaker PlacementFront Speaker Placement Placement of Surround Speakers in a 7.1- Channel SystemGetting Started Source Assignment WorksheetGetting Started Installation Turn on your source device Step Eight Program Sources Into the RemoteStep Nine Turn On the AVR Two steps are required the first time you turn on the AVRUsing the On-Screen Menu System Initial SetupConfigure the AVR 160, Using EzSet/EQ Technology Channel Inputs Set Up SourcesHDMI-Equipped Multichannel Disc Player System Settings Dim FunctionOperation RDS Tuning HeadphonesUsing the Radio Source SelectionProgram Search PTY RecordingRDS Display Options Program Type PTYSelecting a Surround Mode Surround Modes MenuDigital Audio Signals Analog Audio SignalsAudio Processing and Surround Sound Advanced Functions Dolby Surround SettingsIndicates that an LFE channel is present Step ONE Determine Speaker Crossover Manual Speaker SetupStep Three Manual Setup Menu Step TWO Measure Speaker DistancesCrossover Menu Sub ModeNumber of Speakers Distance MenuStep Four Setting Channel Output Levels Manually Audio SettingsWhen you have finished, press the OSD Button Punch-Through Programming Advanced Remote Control FunctionsResetting the Remote MacrosAppendix Appendix Default settingsTable A1 Recommended Source Component Connections Table A3 Speaker/Channel Setting Defaults Table A2 Source Setting DefaultsTable A4 Delay Setting Defaults AUX Tuner Table A5 Source Input SettingsTable A6 Speaker/Channel Settings LFETable A9 Surround Modes Table A7 Remote Control CodesTable A8 System Settings VCR, PVR, DMCDTS-HD DTS-ES Discrete See below Mode GroupTuner Setting to be off DTS StereoTable A10 - Remote Control Function List 50 51 54 55DVD AUX Table A12 Remote Control Product Codes VCR Table A11 Remote Control Product Codes TVTable A13 Remote Control Product Codes CD Table A15 Remote Control Product Codes SAT Table A14 Remote Control Product Codes DVDTable A17 Remote Control Product Codes Cable Processor Reset Troubleshooting GuideMemory AM Tuner Section Technical SpecificationsFM Tuner Section Video Section

AVR 160 specifications

The Harman-Kardon AVR 160 is a versatile and powerful audio/video receiver that delivers a remarkable home theater experience. Designed for audio enthusiasts and casual listeners alike, this model combines cutting-edge technology, sophisticated design, and intuitive controls.

One of the standout features of the AVR 160 is its robust 7.1-channel surround sound output, which supports the latest audio formats including Dolby TrueHD and DTS-HD Master Audio. This allows users to enjoy a truly immersive sound experience when watching movies or playing video games. With a total power output of 75 watts per channel, the AVR 160 ensures that every sound detail is crystal clear, from explosive action sequences to the softest dialogue.

Another significant aspect of the AVR 160 is its advanced connectivity options. It comes equipped with multiple HDMI inputs, allowing you to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. The HDMI 1.4 version support ensures compatibility with 3D video and offers audio return channel (ARC) functionality, simplifying connections with your TV. Additionally, the receiver features wide compatibility with legacy devices through analog audio inputs, as well as USB ports for direct playback of your music collections.

The AVR 160 also includes Harman's proprietary technology, like the EZSet/EQ automatic speaker calibration system. This feature effortlessly optimizes speaker performance by analyzing the acoustic properties of your room and adjusting settings accordingly. Users can also benefit from the integrated SiriusXM and Spotify support, allowing streaming of music directly through the receiver.

In terms of design, the AVR 160 presents a sleek aesthetic that complements any home entertainment setup. The minimalist front panel, with its bright display and easy-to-use controls, makes operation straightforward. Whether you are adjusting settings or selecting inputs, the receiver’s user-friendly interface enhances the overall experience.

In conclusion, the Harman-Kardon AVR 160 is an exceptional receiver that boasts remarkable audio quality, extensive connectivity options, innovative technologies, and a stylish design. Whether you're a movie enthusiast, music lover, or gaming aficionado, this receiver is well-equipped to meet diverse entertainment needs and elevate your audio experience to new heights.