Harman-Kardon AVR 147 Step Six Plug in AC Power, Step Seven Insert Batteries in Remote

Page 24

INSTALLATION

If you used S-video for any sources, or if all of your sources used HDMI or component video, connect the S-video Monitor output on the receiver to an S-video input on your display. See Figure 31. Make a note of how the input is labeled.

If you used composite video for any sources, connect the composite video Monitor output on the receiver to a composite video input on the display. See Figure 31. Again, make a note of how this input is labeled on the display.

Figure 31 – S-Video and Composite Video Monitor Outputs

Consult the manual for your TV to make sure you understand how to select each video input. As you play different source devices that use different types of video connections, select the correct video input on your video display.

Step Six – Plug in AC Power

Having made all of your wiring connections, it is now time to plug each component’s AC power cord into a working outlet.

You may plug one device into the AC Switched Accessory Outlet on the rear of the AVR 147. See Figure 32. Make sure this device draws no more than 50 watts. The device should have its mechanical or master power switch turned on, and it will power on any time the AVR 147 is turned on.

Figure 32 – Switched AC Accesssory Outlet

Before plugging the AVR 147’s AC Power Cord into an electrical outlet, make sure that the Master Power Switch on the front panel is popped out so that the word OFF appears on its top. Gently press the button to turn the switch off. This will prevent the possibility of damaging the AVR in case of a transient power surge.

Step Seven – Insert Batteries in Remote

The AVR 147 remote control uses three AAA batteries, which are included.

To remove the battery cover located on the back of the remote, firmly press the ridged depression and slide the cover toward the top of the remote.

Insert the batteries as shown in Figure 33, making sure to observe the correct polarity.

Figure 33 – Remote Battery Compartment

When using the remote, remember to point the lens toward the front panel of the AVR 147. Make sure no objects, such as furniture, are blocking the remote’s path to the receiver. Bright lights, fluorescent lights and plasma video displays may interfere with the remote’s functioning. The remote has a range of about 20 feet, depending on the lighting conditions. It may be used at an angle of up to 30 degrees to either side of the AVR.

If the remote seems to operate intermittently, or if pressing a button on the remote does not cause the AVR Selector or one of the Input Selectors to light up, then make sure the batteries have been inserted correctly, or replace all three batteries with fresh ones.

Step Eight – Program Sources Into the Remote

The AVR 147 remote not only is capable of controlling the receiver, but it may also be programmed to control many brands and models of VCRs, DVD players, CD players, cable boxes, satellite receivers, cassette decks and TVs, as well as an iPod docked in The Bridge.

It may help to think of the remote as a book with pages. Each page represents the button functions for a different device. In order to access the functions for a particular device, you first need to “turn to that page”; that is, switch the remote to that device mode. This is done by pressing the AVR Button to access the codes that control the receiver, or the Input Selector buttons to access the codes for the devices programmed into the remote.

You may have noticed that three of the Input Selectors look different from the others (see Figure 34). For the DVD/CD, TAPE/The Bridge and HDMI 1/HDMI 2 Selectors, there is a primary source, whose name is printed on the button, and a secondary source, whose name is printed in green above the button.

When the remote is in the device mode for the primary source, e.g. DVD, pressing the device selector will cause it to light up in red. When the remote is in the secondary source’s device mode, the selector will light up in green when pressed.

To switch between the primary and secondary device modes, press the selector twice quickly in succession. The selector will retain this selection until the next time you toggle between the primary and secondary device modes. That is, if you press the DVD/CD Selector twice quickly so that the CD source is activated, then press another source selector, such as Video 1, the next time you press the DVD/CD Selector, the remote will return to the CD device mode.

The AVR 147’s remote is factory-programmed to control an iPod docked in The Bridge and many Harman Kardon DVD and CD players.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents AVR Safety Information Safety Information Important Safety InformationStaple Invoice Here Table of Contents Introduction Thank you for choosing Harman KardonAudio Section Surround ModesSupplied Accessories Audio InputsAudio/Video Inputs With S-Video Digital Audio InputsFRONT-PANEL Controls Navigation Adjust Input Indicators REAR-PANEL Connections DVD A/V Remote Control Functions Video 3 Controls televisions and other video displaysChannel Input Selector Press this button to select Power On AVR SelectorRemote Control Functions Introduction to Home Theater Surround ModesTypical Home Theater System Multichannel AudioConnecting Source Devices to the AVR ConnectionsTypes of Connections Speaker ConnectionsAudio Connections Digital AudioVideo Connections Analog AudioFM antenna uses a 75-ohm F-connector. See Figure AntennasAnalog Video RS-232 Serial PortSpeaker Placement Installation Step One Connect the SpeakersStep Two Connect the Subwoofer Step Three Connect the AntennasVideo 1 Source VCR, DVR, PVRVideo 2 Source Video 3 SourceHdmi 1 Source Step Five Connect the Video Display Hdmi 2 SourceTape No video connections are neededStep Six Plug in AC Power Step Seven Insert Batteries in RemoteTurn on your source device Enter a code from aboveStep Nine Turn On the AVR Two steps are required the first time you turn on the AVRInitial Setup Using the On-Screen Menu SystemConfigure the AVR 147 Using EzSet/EQ After your desired setting appearsPlug EzSet/EQ microphone into receiver What EzSet/EQ Does EzSet/EQ Specifying a 7.1 SystemConfigure Sources EzSet/EQ CompletedTuner at this time › Button selects the sources in the reverse orderAudio input assigned to the source DMP Setting Menu Screen You are now ready to begin enjoying your new receiverSleep Timer Volume ControlOperation Turning On the AVRHeadphones Mute FunctionTone Controls Source SelectionAudio Input Selection Video Input SelectionChannel Direct Inputs We recommend that you connect this player as followsUsing the Tuner Channel Input SelectorXM Radio Operation RecordingUsing TheBridgeTM Tuning DownSelecting a Surround Mode Select a Surround Mode RemoteAnalog Audio Signals Digital Audio SignalsAdvanced Functions Audio Processing and Surround SoundDolby Surround Settings Default Modes 0 orDolby Digital EX played as Passages to avoid disturbing othersSurround Mode Description Incoming Bitstream or Signal Panorama adjusts wraparound surround effectSee below Dolby Digital 2.0 orAre available Logic Manual Setup Step Three Manual Setup MenuStep Two Measure Speaker Distances Step One Determine Speaker SizeLarge setting Speaker Size MenuDelay Adjust Menu Speaker Crossover MenuStep Four Setting Channel Output Levels Manually Using the Remote Control With the Test ToneUsing the Front-Panel or Remote Control Channel Command Make sure all speakers have been connected correctlySystem Settings Using the Full-OSD MenuAdvanced Remote Control Functions Dim FunctionPunch-Through Programming To dim the displayResetting the Remote To program, or record a macro, follow these stepsProcessor Reset Troubleshooting Guide AVR 147 Technical Specifications DTSAppendix Default settings, worksheets, remote product codes Table A1 Source Input Setting DefaultsTable A2 Speaker/Channel Setting Defaults Table A3 Delay Setting DefaultsTable A4 Source Input Setting Table A5 Speaker/Channel SettingTable A6 Remote Control Codes Table A7 System SettingsRemote Control Function List Reference Remote Control Function List TV VID3FAV Aiwa Table A9 Table A10Table A11 Remote Control Product Codes CD Table A12 Remote Control Product Codes DVDTable A13 Remote Control Product Codes SAT Table A14 Remote Control Product Codes TapeTable A15 Remote Control Product Codes CBL Table A16 Remote Control Product Codes Table A15Page
Related manuals
Manual 52 pages 60.25 Kb Manual 2 pages 42.45 Kb

AVR 147 specifications

The Harman-Kardon AVR 147 is an entry-level receiver designed for those who seek quality audio and video experiences without overcomplicating their setup. This model is part of Harman-Kardon's well-known line of audio-video receivers, designed to provide an immersive home theater experience.

At the heart of the AVR 147 is its 5.1 channel surround sound capability, allowing for the connection of up to five speakers plus a subwoofer. This configuration enables a rich sound field that envelops listeners, ideal for both movies and music. The receiver can deliver up to 40 watts per channel, providing sufficient power for a modest home theater setup. The incorporation of Dolby Digital and DTS decoding ensures that users can enjoy their favorite movies with cinematic sound quality.

One of the main features of the AVR 147 is its user-friendly interface. The simplified remote control and intuitive on-screen menu make it easy for users to navigate settings and optimize sound performance. The receiver also offers multiple inputs, including HDMI, component, composite, and optical connections, ensuring compatibility with a wide range of audio and video sources, such as Blu-ray players, gaming consoles, and streaming devices.

The AVR 147 is equipped with Harman Kardon’s proprietary technologies, including the Advanced DSP (Digital Signal Processing), which enhances audio quality and clarity. Moreover, it supports various surround sound formats, allowing users to enjoy an enhanced home theater experience tailored to their preferences.

Another noteworthy characteristic is its sleek, modern design, which blends seamlessly into any entertainment setup. With its front panel display, users can easily see their settings and selections. The robust build quality of the AVR 147 ensures durability and longevity, making it a wise investment for those passionate about audio-visual technology.

In terms of video accessories, the AVR 147 can upscale standard-resolution video sources to provide a better viewing experience. Although it lacks some of the advanced features found in higher-end models, the AVR 147 remains a commendable choice for anyone seeking an effective and powerful home theater solution without excessive complexity. Whether you're watching movies, playing video games, or enjoying your favorite music, the Harman-Kardon AVR 147 is a reliable companion in elevating home entertainment experiences.
Top Page Image Contents