Kenmore 625.38306 Sanitize the Water Softener, Sanitize Your Water Softener AS Follows

Page 20

SANITIZE THE WATER SOFTENER

Care is taken at the factory to keep your water softener clean and sanitary. Materials used to make the softener will not infect or contaminate your water supply, or cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the softener.

SANITIZE YOUR WATER SOFTENER AS FOLLOWS:

1.Be certain the bypass valve is pulled out to "service" position.

2.Lift the salt hole cover and using a pail add up to 3 gallons of water to the salt storage tank.

3.Remove the brine well cover (Fig. 28) and pour about 3/4 ounce, or 1 to 2 tablespoons, of common 5.25% 1, unscent- ed, household bleach (Clorox, Linco, BoPeep, White Sail, Eagle, etc.) in the softener brinewell. Replace the brinewell cover.

4.Press the REGENERATION button and hold for 3 seconds to start a recharge. This first recharge does several things.

•It draws the bleach into and through the softener to sani- tize it.

•It fills the salt tank to the water level needed.

•It gets all the air out of the resin tank.

•It prepares the resin bed (see page 25) for service and flushes residual chlorine from the softener.

NOTE: This recharge takes about 2-1/2to 2-3/4hours, depending on the salt type setting.

NOTE: During a recharge the water softener bypasses raw water to the home. You will not get salty water or affect the regeneration cycle if water is used at this time.

You can sanitize the softener with or without salt in the storage tank.

1Recommended by the Water Quality Association.

On some water supplies, the water softener may need peri- odic disinfecting.

Your new Sears softener is now softening the water for your household needs. However, your WATER HEATER is filled with hard water. To have fully soft water right away, you can drain the water heater so it refills with soft water. If you don't drain the water heater, it will take a few days before you have fully soft water.

To drain the water heater, open a hot water faucet and let it run until the water runs cold. Then close the faucet.

NOTE: If this procedure is performed on a new softener, water coming from the taps may initially be discolored.

This normally occurs the first time water runs through the resin bed. The discolored water is not harmful, and the discoloration will not last more than a few minutes.

Salt Hole Cover

Water About 3 gallons

/2 /Brinewell Cover

(Remove and

/add about

3/4 oz. bleach)

/

f Brinewell

/

FIG. 28

Questions? Call The Kenmore Water Line 1-800-426-9345

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Water Softener Save this ManualONE Year Limited Warranty on Water Softener TEN Year Limited Warranty Against LeaksQuestions? Questions? Call The Kenmore Water Line Parts Descriptions Small Inspect ShipmentProper Order to Install Water Treating Equipment Plan Your InstallationTools Needed PipeTypical Installation Where to Install the Water SoftenerSuggested Slab Foundation Installation Draw Your Pipes FittingsClip Before Installing Checks & Tests Adding a pressure reducing valve may reduce the flowInlet and Outlet Threaded Adaptors Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveBypass Valve Bypass Valve Turned Downward Installing Holding ClipsValve Bypass Move Softener Into Place Typical Soldering ConnectionsPosition Softener Into Place Connect the SoftenerConnect the Valve Drain Hose Connect Salt Tank Overflow TubingLeak Test House Main Water Shutoff ValvesSingle Bypass Water Meter Jumper Wire Connecting TransformerElectrical Power Outlet for Your Softener Cold Water Pipe GroundingRestart the Water Heater Install CoversInstall Covers Program the Timer SET Present Time of DAYSET Water Hardness Number Hardness NumberSET Regeneration Time SET Salt LevelSanitize the Water Softener Sanitize Your Water Softener AS FollowsWater Softening Salt with Iron Removing AdditivesCheck List of STEP-BY-STEP Guides to Install Unit plugged Into a continuously live outlet?Salt Monitor System Recharge NOWRecharge Tonight Program Memory Efficiency ModeError Code Regeneration Soft Water Service and RegenerationService Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in BackwashElectronics Soft Water Service and Regeneration Automatic BypassWater Flow Through Softener Fast Rinse Salt Bridge Salt BridgeCleaning Nozzle & Venturi Keeping the Water Softener Clean Iron from Resin BEDDrain ALL Water from Softener Protect the Water Softener from FreezingCorrection ProblemcauseChecklist to Help YOU Save Money Model no .383060 Timer Code S Bypass ValvesPressure Drop PSI vs. Flow Rate GPM Eration Check Wiring SchematicAlways Make These Initial Checks First Manual Initiated Electronics Diagnostics Possible Problem Code Most Likely Less LikelyProcedure for Removing Error Code From Faceplate Other Information Troubleshooting Valve Position IndicatorsTimer PWA Replacement Cycle Flow Rates Gallons PER MIN Brine RinseMAX. Backwash MAX. Fast RinseDisassembly AssemblyTo Relieve Pressure Servicing the ValveValve Service Cycle Water Flow Through the SoftenerFill Cycle Brining and Brine Rinse CycleValve Backwash Cycle Fast Rinse CycleBackwash Cycle Fast Rinse CycleQuestions? Call The Kenmore Water Line LiO KeyNo Water Softener CompleteInlet Outlet Grounding Clamps Brine Valve Assembly Key No. Part Number Part Description11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home Water Softener Warranty on Water Softener Questions? Questions? Call The Kenmore Water Line Parts Descriptions Small DeFa ce s Typical Installation Suggested Slab Foundation Installation Clip Before Installing Checks & Tests Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve Valve Bypass Move Softener Into Place Connect the Valve Drain Hose House Main Water Shutoff Valves Installgroundingclampbetween Thesoftenerinand OUT Pipes Install Covers PMI UP or Down button in changes the display twice each second Sanitize the Water Softener Addingsalttothe Storagetank Check List of STEP-BY-STEP Guides to Install 312 Nun @ Questions? Call The Kenmore Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener Fast Rinse Salt Bridge Iron from Resin BED Drain ALL Water from Softener Problemcause Bypass Valves Pressure Drop PSI vs. Flow Rate GPM Faceplate Procedure for Removing Error Code From Faceplate Sc,l Root sto Rotaryvalveservice Water Flow Through the Softener Valve Backwash Cycle Questions? Call The Kenmore Water Line LiO KeyNo Inlet Outlet Grounding Clamps Brine Valve Assembly 11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home

625.38306 specifications

The Kenmore 625.38306 is a standout model in the realm of home appliances, particularly known for its advanced air filtration and humidification capabilities. Designed with the modern homeowner in mind, this unit effectively blends functionality with ease of use.

One of the key features of the Kenmore 625.38306 is its powerful air purification system. Equipped with a high-efficiency particulate air (HEPA) filter, it captures up to 99.97% of airborne particles, including dust, pollen, pet dander, and smoke. This capability ensures that the air in your home is not only cleaner but also healthier for you and your family. The HEPA filter is designed for longevity, providing extended usage before needing to be replaced, which adds to the convenience.

In addition to its air purification prowess, the Kenmore 625.38306 also includes a built-in humidifier. This feature allows users to maintain optimal humidity levels in their home, which can be particularly beneficial during dry winter months. Proper humidity control can alleviate symptoms of dry skin, respiratory issues, and can even help protect wooden furniture and floors from cracking due to excessive dryness. The humidification technology operates quietly in the background, ensuring a peaceful environment.

The design of the Kenmore 625.38306 is both sleek and functional. With a user-friendly interface, it features intuitive controls that allow users to easily adjust settings. The digital display provides real-time feedback on indoor air quality, humidity levels, and filter status, ensuring users are well informed about their environment. Additionally, the compact design makes it versatile enough to fit in various room sizes, from bedrooms to living areas.

Energy efficiency is another notable characteristic of the Kenmore 625.38306. It is designed to operate at low power consumption levels without compromising performance, making it an environmentally friendly choice. This unit is also equipped with automatic shut-off and sleep modes to enhance energy savings while maintaining optimal air quality.

In summary, the Kenmore 625.38306 is a highly effective air purifier and humidifier that excels in delivering clean and healthy indoor air. With its advanced filtration system, convenient humidity control, user-friendly design, and energy efficiency, this model stands out as a reliable choice for anyone looking to enhance their home environment. Whether you have allergies, respiratory concerns, or simply want to create a more comfortable living space, the Kenmore 625.38306 provides the solution you need.
Top Page Image Contents