Kenmore 625.38306 owner manual Typical Installation

Page 55

shutoff valve

FIG. 3

Typical Installation

WHERE TO INSTALL THE WATER SOFTENER

Review the following points before you choose a place

1.Place as close as possible but always after, the pressure tank (well water) or water meter (city water). See Fig. 3.

2.Place as close as possible to a water drain such as a floor drain, laundry tub, sump or standpipe. See Fig. 3.

3.Connect to the house main water pipe BEFORE THE WATER HEATER. See Fig. 3. Temperature of water going through the softener must not be more than 120°F (49°C). Hot water will damage inner softener parts. To reduce the risk of hot water backup, piping between the softener and water heater should be as long of a run as possible.

4.Keep outside faucets on hard water to save soft water and salt. See Fig. 3.

5.Do not install in a place where the softener could freeze. Damage caused by freezing voids the war- ranty by Sears Brands Management Corporation.

to put your softener.

6.Put the softener in a place where water damage is least likely to occur if it develops a leak. Sears or the manufacturer will not repair or pay for water damage.

7.A grounded, 120V electrical outlet is needed within 10 feet of the softener. See Fig. 3. This is to plug in the transformer. The softener has a 10 foot power cable. Be sure the outlet and transformer are in an inside place, to protect from wet weather. Use a continuously "live" outlet, which cannot be acci- dentally switched off.

8.When installing in an outside location, you must take the steps necessary to assure the softener, installa- tion plumbing, and wiring, are protected from the

elements, direct sunlight, contamination, vandalism, etc.

Questions? Call The Kenmore Water Line 1-800-426-9345

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Save this Manual Water SoftenerTEN Year Limited Warranty Against Leaks ONE Year Limited Warranty on Water SoftenerQuestions? Questions? Call The Kenmore Water Line Inspect Shipment Parts Descriptions SmallPipe Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededWhere to Install the Water Softener Typical InstallationDraw Your Pipes Fittings Suggested Slab Foundation InstallationClip Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsBypass Valve Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveInlet and Outlet Threaded Adaptors Valve Bypass Installing Holding ClipsBypass Valve Turned Downward Connect the Softener Move Softener Into PlaceTypical Soldering Connections Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseSingle Bypass House Main Water Shutoff ValvesLeak Test Cold Water Pipe Grounding Water Meter Jumper WireConnecting Transformer Electrical Power Outlet for Your SoftenerInstall Covers Install CoversRestart the Water Heater SET Present Time of DAY Program the TimerSET Salt Level SET Water Hardness NumberHardness Number SET Regeneration TimeSanitize Your Water Softener AS Follows Sanitize the Water SoftenerRemoving Additives Water Softening Salt with IronUnit plugged Into a continuously live outlet? Check List of STEP-BY-STEP Guides to InstallRecharge Tonight Recharge NOWSalt Monitor System Error Code Efficiency ModeProgram Memory Service Soft Water Service and RegenerationRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseWater Flow Through Softener Fast Rinse Soft Water Service and Regeneration Automatic BypassElectronics Salt Bridge Salt BridgeIron from Resin BED Cleaning Nozzle & Venturi Keeping the Water Softener CleanProtect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money ProblemcauseCorrection Bypass Valves Model no .383060 Timer Code SPressure Drop PSI vs. Flow Rate GPM Always Make These Initial Checks First Wiring SchematicEration Check Procedure for Removing Error Code From Faceplate Possible Problem Code Most Likely Less LikelyManual Initiated Electronics Diagnostics Timer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information MAX. Fast Rinse Cycle Flow Rates Gallons PER MINBrine Rinse MAX. BackwashServicing the Valve DisassemblyAssembly To Relieve PressureBrining and Brine Rinse Cycle Valve Service CycleWater Flow Through the Softener Fill CycleFast Rinse Cycle Valve Backwash CycleFast Rinse Cycle Backwash CycleQuestions? Call The Kenmore Water Line LiO Water Softener Complete KeyNoInlet Outlet Grounding Clamps Key No. Part Number Part Description Brine Valve Assembly11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home Water Softener Warranty on Water Softener Questions? Questions? Call The Kenmore Water Line Parts Descriptions Small DeFa ce s Typical Installation Suggested Slab Foundation Installation Clip Before Installing Checks & Tests Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve Valve Bypass Move Softener Into Place Connect the Valve Drain Hose House Main Water Shutoff Valves Installgroundingclampbetween Thesoftenerinand OUT Pipes Install Covers PMI UP or Down button in changes the display twice each second Sanitize the Water Softener Addingsalttothe Storagetank Check List of STEP-BY-STEP Guides to Install 312 Nun @ Questions? Call The Kenmore Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener Fast Rinse Salt Bridge Iron from Resin BED Drain ALL Water from Softener Problemcause Bypass Valves Pressure Drop PSI vs. Flow Rate GPM Faceplate Procedure for Removing Error Code From Faceplate Sc,l Root sto Rotaryvalveservice Water Flow Through the Softener Valve Backwash Cycle Questions? Call The Kenmore Water Line LiO KeyNo Inlet Outlet Grounding Clamps Brine Valve Assembly 11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home

625.38306 specifications

The Kenmore 625.38306 is a standout model in the realm of home appliances, particularly known for its advanced air filtration and humidification capabilities. Designed with the modern homeowner in mind, this unit effectively blends functionality with ease of use.

One of the key features of the Kenmore 625.38306 is its powerful air purification system. Equipped with a high-efficiency particulate air (HEPA) filter, it captures up to 99.97% of airborne particles, including dust, pollen, pet dander, and smoke. This capability ensures that the air in your home is not only cleaner but also healthier for you and your family. The HEPA filter is designed for longevity, providing extended usage before needing to be replaced, which adds to the convenience.

In addition to its air purification prowess, the Kenmore 625.38306 also includes a built-in humidifier. This feature allows users to maintain optimal humidity levels in their home, which can be particularly beneficial during dry winter months. Proper humidity control can alleviate symptoms of dry skin, respiratory issues, and can even help protect wooden furniture and floors from cracking due to excessive dryness. The humidification technology operates quietly in the background, ensuring a peaceful environment.

The design of the Kenmore 625.38306 is both sleek and functional. With a user-friendly interface, it features intuitive controls that allow users to easily adjust settings. The digital display provides real-time feedback on indoor air quality, humidity levels, and filter status, ensuring users are well informed about their environment. Additionally, the compact design makes it versatile enough to fit in various room sizes, from bedrooms to living areas.

Energy efficiency is another notable characteristic of the Kenmore 625.38306. It is designed to operate at low power consumption levels without compromising performance, making it an environmentally friendly choice. This unit is also equipped with automatic shut-off and sleep modes to enhance energy savings while maintaining optimal air quality.

In summary, the Kenmore 625.38306 is a highly effective air purifier and humidifier that excels in delivering clean and healthy indoor air. With its advanced filtration system, convenient humidity control, user-friendly design, and energy efficiency, this model stands out as a reliable choice for anyone looking to enhance their home environment. Whether you have allergies, respiratory concerns, or simply want to create a more comfortable living space, the Kenmore 625.38306 provides the solution you need.
Top Page Image Contents