Kenmore 625.38306 owner manual Valve Bypass

Page 60

Before installing the bypass valve, or copper tube, be sure the turbine and support are firmly in place in the valve outlet port.

Turbine
Support	Sensor Port

H/I

Turbine

FIG. 10

INSTALLING	HOLDING	CLIPS
Black Cli	Cross	Section of Valve
Bypass Valve or	Inlet or Outlet

Installation Adaptor

O-Ring

Clip Sna)s into Place

Between Larger Diameter Rings

FIG. 11

BYPASS VALVE TURNED DOWNWARD

Turn bypass valve upside down to connect to floor

level plumbing.

OUT

IN

FIG. 12

INSTALLING 3 VALVE BYPASS AND PIPES Complete the following steps to install the three (3) valve bypass:

3 VALVE BYPASS

•Cut the house main water pipe where you will con- nect the softener.

•Loosely put together pipe, fittings, and the three

(3) valves.

•Place valve(s) within easy reach.

When all pipe, fittings and valves make a good fit together, tighten all threaded joints (use pipe dope on outside threads), or solder all sweat joints.

TO

FIG. 13

Softener Inlet

Questions? Call The Kenmore Water Line 1-800-426-9345

12

Image 60

Contents Water Softener Save this ManualONE Year Limited Warranty on Water Softener TEN Year Limited Warranty Against LeaksQuestions? Questions? Call The Kenmore Water Line Parts Descriptions Small Inspect ShipmentProper Order to Install Water Treating Equipment Plan Your InstallationTools Needed PipeTypical Installation Where to Install the Water SoftenerSuggested Slab Foundation Installation Draw Your Pipes FittingsClip Before Installing Checks & Tests Adding a pressure reducing valve may reduce the flowAssemble Inlet Outlet ADAPTORS, or Single Bypass Valve Bypass ValveInlet and Outlet Threaded Adaptors Installing Holding Clips Valve BypassBypass Valve Turned Downward Move Softener Into Place Typical Soldering ConnectionsPosition Softener Into Place Connect the SoftenerConnect the Valve Drain Hose Connect Salt Tank Overflow TubingHouse Main Water Shutoff Valves Single BypassLeak Test Water Meter Jumper Wire Connecting TransformerElectrical Power Outlet for Your Softener Cold Water Pipe GroundingInstall Covers Install CoversRestart the Water Heater Program the Timer SET Present Time of DAYSET Water Hardness Number Hardness NumberSET Regeneration Time SET Salt LevelSanitize the Water Softener Sanitize Your Water Softener AS FollowsWater Softening Salt with Iron Removing AdditivesCheck List of STEP-BY-STEP Guides to Install Unit plugged Into a continuously live outlet?Recharge NOW Recharge TonightSalt Monitor System Efficiency Mode Error CodeProgram Memory Soft Water Service and Regeneration ServiceRegeneration Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in BackwashSoft Water Service and Regeneration Automatic Bypass Water Flow Through Softener Fast RinseElectronics Salt Bridge Salt BridgeCleaning Nozzle & Venturi Keeping the Water Softener Clean Iron from Resin BEDDrain ALL Water from Softener Protect the Water Softener from FreezingProblemcause Checklist to Help YOU Save MoneyCorrection Model no .383060 Timer Code S Bypass ValvesPressure Drop PSI vs. Flow Rate GPM Wiring Schematic Always Make These Initial Checks FirstEration Check Possible Problem Code Most Likely Less Likely Procedure for Removing Error Code From FaceplateManual Initiated Electronics Diagnostics Troubleshooting Valve Position Indicators Timer PWA ReplacementOther Information Cycle Flow Rates Gallons PER MIN Brine RinseMAX. Backwash MAX. Fast RinseDisassembly AssemblyTo Relieve Pressure Servicing the ValveValve Service Cycle Water Flow Through the SoftenerFill Cycle Brining and Brine Rinse CycleValve Backwash Cycle Fast Rinse CycleBackwash Cycle Fast Rinse CycleQuestions? Call The Kenmore Water Line LiO KeyNo Water Softener CompleteInlet Outlet Grounding Clamps Brine Valve Assembly Key No. Part Number Part Description11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home Water Softener Warranty on Water Softener Questions? Questions? Call The Kenmore Water Line Parts Descriptions Small DeFa ce s Typical Installation Suggested Slab Foundation Installation Clip Before Installing Checks & Tests Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve Valve Bypass Move Softener Into Place Connect the Valve Drain Hose House Main Water Shutoff Valves Installgroundingclampbetween Thesoftenerinand OUT Pipes Install Covers PMI UP or Down button in changes the display twice each second Sanitize the Water Softener Addingsalttothe Storagetank Check List of STEP-BY-STEP Guides to Install 312 Nun @ Questions? Call The Kenmore Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener Fast Rinse Salt Bridge Iron from Resin BED Drain ALL Water from Softener Problemcause Bypass Valves Pressure Drop PSI vs. Flow Rate GPM Faceplate Procedure for Removing Error Code From Faceplate Sc,l Root sto Rotaryvalveservice Water Flow Through the Softener Valve Backwash Cycle Questions? Call The Kenmore Water Line LiO KeyNo Inlet Outlet Grounding Clamps Brine Valve Assembly 11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home