Kenmore 625.38306 owner manual Questions? Call The Kenmore Water Line

Page 4

Read all steps, guides and rules carefully before installing and using your new water softener. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury

or property damage. Reading this book will also help you to get all of the benefits from your water softener.

Your Kenmore Water Softener will remove hardness minerals from water. This is measured in

grains per gallon (gpg). It will also remove some clear water iron*. This is measured in parts

per million(ppm). See the specifications page for the maximum limits of hardness and iron removal.

A water softener will not improve other water problems such as acidity, tastes and odors, or

iron other than clear water iron. It will not purify contaminated water, or make unsafe water safe to drink.

Check with your local public works department for plumbing, electric and sanitation codes. You must follow their guides as you install your softener. Use only LEAD FREE SOLDER AND FLUX, as required by federal and state codes, when installing soldered copper plumb- ing.

Protect the softener and piping from freezing. Damage from freezing voids the softener war- ranty. See how to protect from freezing on page 31.

CAUTION: Please read and comply with the following guides to prevent damage to the sof- tener or other property, personal injury, or possible fatal shock.

This softener works on 24 volts only. Be sure to use only the transformer included. Plug it into a nominal 120V, 60 cycle household outlet that is grounded and properly protected by an overcurrent device such as a circuit breaker or fuse. If transformer is replaced, use only the authorized service Class II, 24 volt, 10 VA transformer.

Unplug the transformer right away if the power cable should become damaged or frayed. Make repairs, or replace the transformer, before plugging back into the power outlet.

Always unplug the softener from electrical power before removing outer valve covers.

This system is not intended to be used for treating water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

* The capacity to reduce clear water iron is substantiated by WQA test data.

European Directive 2002/96/EC requires all electrical and electronic equipment to be disposed of according to Waste Electrical and Electronic Equipment (WEEE) requirements. This directive or similar laws are in place nationally and can vary from region to region. Please refer to your state and local laws for proper disposal of this equipment.

Questions? Call The Kenmore Water Line 1-800-426-9345

4

Image 4
Contents Water Softener Save this ManualONE Year Limited Warranty on Water Softener TEN Year Limited Warranty Against LeaksQuestions? Questions? Call The Kenmore Water Line Parts Descriptions Small Inspect ShipmentProper Order to Install Water Treating Equipment Plan Your InstallationTools Needed PipeTypical Installation Where to Install the Water SoftenerSuggested Slab Foundation Installation Draw Your Pipes FittingsClip Before Installing Checks & Tests Adding a pressure reducing valve may reduce the flowBypass Valve Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveInlet and Outlet Threaded Adaptors Valve Bypass Installing Holding ClipsBypass Valve Turned Downward Move Softener Into Place Typical Soldering ConnectionsPosition Softener Into Place Connect the SoftenerConnect the Valve Drain Hose Connect Salt Tank Overflow TubingSingle Bypass House Main Water Shutoff ValvesLeak Test Water Meter Jumper Wire Connecting TransformerElectrical Power Outlet for Your Softener Cold Water Pipe GroundingInstall Covers Install CoversRestart the Water Heater Program the Timer SET Present Time of DAYSET Water Hardness Number Hardness NumberSET Regeneration Time SET Salt LevelSanitize the Water Softener Sanitize Your Water Softener AS FollowsWater Softening Salt with Iron Removing AdditivesCheck List of STEP-BY-STEP Guides to Install Unit plugged Into a continuously live outlet?Recharge Tonight Recharge NOWSalt Monitor System Error Code Efficiency ModeProgram Memory Service Soft Water Service and RegenerationRegeneration Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in BackwashWater Flow Through Softener Fast Rinse Soft Water Service and Regeneration Automatic BypassElectronics Salt Bridge Salt BridgeCleaning Nozzle & Venturi Keeping the Water Softener Clean Iron from Resin BEDDrain ALL Water from Softener Protect the Water Softener from FreezingChecklist to Help YOU Save Money ProblemcauseCorrection Model no .383060 Timer Code S Bypass ValvesPressure Drop PSI vs. Flow Rate GPM Always Make These Initial Checks First Wiring SchematicEration Check Procedure for Removing Error Code From Faceplate Possible Problem Code Most Likely Less LikelyManual Initiated Electronics Diagnostics Timer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information Cycle Flow Rates Gallons PER MIN Brine RinseMAX. Backwash MAX. Fast RinseDisassembly AssemblyTo Relieve Pressure Servicing the ValveValve Service Cycle Water Flow Through the SoftenerFill Cycle Brining and Brine Rinse CycleValve Backwash Cycle Fast Rinse CycleBackwash Cycle Fast Rinse CycleQuestions? Call The Kenmore Water Line LiO KeyNo Water Softener CompleteInlet Outlet Grounding Clamps Brine Valve Assembly Key No. Part Number Part Description11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home Water Softener Warranty on Water Softener Questions? Questions? Call The Kenmore Water Line Parts Descriptions Small DeFa ce s Typical Installation Suggested Slab Foundation Installation Clip Before Installing Checks & Tests Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve Valve Bypass Move Softener Into Place Connect the Valve Drain Hose House Main Water Shutoff Valves Installgroundingclampbetween Thesoftenerinand OUT Pipes Install Covers PMI UP or Down button in changes the display twice each second Sanitize the Water Softener Addingsalttothe Storagetank Check List of STEP-BY-STEP Guides to Install 312 Nun @ Questions? Call The Kenmore Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener Fast Rinse Salt Bridge Iron from Resin BED Drain ALL Water from Softener Problemcause Bypass Valves Pressure Drop PSI vs. Flow Rate GPM Faceplate Procedure for Removing Error Code From Faceplate Sc,l Root sto Rotaryvalveservice Water Flow Through the Softener Valve Backwash Cycle Questions? Call The Kenmore Water Line LiO KeyNo Inlet Outlet Grounding Clamps Brine Valve Assembly 11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home