Kenmore 625.38306 owner manual Problemcause

Page 79

CHECKLIST TO HELP YOU SAVE MONEY

If your water softener fails to work, make the following easy checks. Often, you will find what is wrong yourself and you won't have to call and wait for service. If you do not find anything wrong while making the checks, and your sof- tener still does not work, call your Sears Service Department.

1.Also read ERROR CODE.

2.If an error code is not displayed, press and hold the SELECT button until the display changes. Then, press the SELECT button again and hold until a flashing model code appears. For Model No. 625.383060 it must show

S 25. If any other number shows, the face plate computer is working on incorrect input and would probably be the cause of the problem. To set the correct code, press either the UP or DOWN button. When correct model code

(S 25) shows, press SELECT to return a flashing 12:00 AM display. Reset the present time, hardness number, etc.

PROBLEMCAUSE

No soft water

No salt (or salt bridged) in the storage tank

CORRECTION

Add salt, see page 22, or break the salt bridge, see page 29. Press REGENERATION button and hold to start a regeneration, see page 23.

Water hard sometimes

Brine tank flooded

Salty tasting water

immediately after regeneration

Transformer unplugged at the watt outlet, or power cable leads loose from the electronic

board, fuse blown, circuit breaker popped, or circuit switched off.

Manual bypass valve(s) in bypass position

Dirty, plugged or damaged nozzle venturi

Valve drain hose plugged or restricted

Hardness number setting too low

Using hot water when softener is regenerat- ing

Increase in the grains of hardness in your water supply

Restricted drain line

Plugged or dirty nozzle & venturi

Valve rotor-disc & seals

Restricted drain line

Check for loss of power due to any of these and correct. With the power back on, look at the time display and read PROGRAM MEMO- RY, see page 24.

Look at Fig. 18 & 19 on page 15. Move the stem in a single valve to service. In a 3-valve bypass, open the inlet and outlet valve, and be sure to fully close the bypass valve.

Take apart and clean or replace damaged parts, see page 29.

The drain hose must not have kinks, sharp bends, or be raised too high above the soften- er, see page 14.

Press and release the SELECT button until HARDNESS shows in the display. Read the hardness number in the display and be sure the same grains per gallon number is shown

as on your water analysis report. See page 19 to reset. Press and release the SELECT button

until the present time shows in the display.

Avoid using hot water during this time because the water heater refills with hard water, see Automatic Bypass, page 27.

Ask your Sears retail store for a new water analysis. Then make a new hardness number setting, page 19.

Check for kinks, bends or obstructions, see page 14.

Take apart and clean or replace damaged parts, see page 29.

Check for scratches or grooves, replace if needed.

Check for kinks, bends or obstructions, see page 14.

Questions? Call The Kenmore Water Line 1-800-426-9345

31

Page 78 Page 80
Image 79
Page 78 Page 80
Contents Save this Manual Water SoftenerTEN Year Limited Warranty Against Leaks ONE Year Limited Warranty on Water SoftenerQuestions? Questions? Call The Kenmore Water Line Inspect Shipment Parts Descriptions SmallPipe Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededWhere to Install the Water Softener Typical InstallationDraw Your Pipes Fittings Suggested Slab Foundation InstallationClip Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsBypass Valve Assemble Inlet Outlet ADAPTORS, or Single Bypass ValveInlet and Outlet Threaded Adaptors Valve Bypass Installing Holding ClipsBypass Valve Turned Downward Connect the Softener Move Softener Into PlaceTypical Soldering Connections Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseSingle Bypass House Main Water Shutoff ValvesLeak Test Cold Water Pipe Grounding Water Meter Jumper WireConnecting Transformer Electrical Power Outlet for Your SoftenerInstall Covers Install CoversRestart the Water Heater SET Present Time of DAY Program the TimerSET Salt Level SET Water Hardness NumberHardness Number SET Regeneration TimeSanitize Your Water Softener AS Follows Sanitize the Water SoftenerRemoving Additives Water Softening Salt with IronUnit plugged Into a continuously live outlet? Check List of STEP-BY-STEP Guides to InstallRecharge Tonight Recharge NOWSalt Monitor System Error Code Efficiency ModeProgram Memory Service Soft Water Service and RegenerationRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseWater Flow Through Softener Fast Rinse Soft Water Service and Regeneration Automatic BypassElectronics Salt Bridge Salt BridgeIron from Resin BED Cleaning Nozzle & Venturi Keeping the Water Softener CleanProtect the Water Softener from Freezing Drain ALL Water from SoftenerChecklist to Help YOU Save Money ProblemcauseCorrection Bypass Valves Model no .383060 Timer Code SPressure Drop PSI vs. Flow Rate GPM Always Make These Initial Checks First Wiring SchematicEration Check Procedure for Removing Error Code From Faceplate Possible Problem Code Most Likely Less LikelyManual Initiated Electronics Diagnostics Timer PWA Replacement Troubleshooting Valve Position IndicatorsOther Information MAX. Fast Rinse Cycle Flow Rates Gallons PER MINBrine Rinse MAX. BackwashServicing the Valve DisassemblyAssembly To Relieve PressureBrining and Brine Rinse Cycle Valve Service CycleWater Flow Through the Softener Fill CycleFast Rinse Cycle Valve Backwash CycleFast Rinse Cycle Backwash CycleQuestions? Call The Kenmore Water Line LiO Water Softener Complete KeyNoInlet Outlet Grounding Clamps Key No. Part Number Part Description Brine Valve Assembly11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home Water Softener Warranty on Water Softener Questions? Questions? Call The Kenmore Water Line Parts Descriptions Small DeFa ce s Typical Installation Suggested Slab Foundation Installation Clip Before Installing Checks & Tests Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve Valve Bypass Move Softener Into Place Connect the Valve Drain Hose House Main Water Shutoff Valves Installgroundingclampbetween Thesoftenerinand OUT Pipes Install Covers PMI UP or Down button in changes the display twice each second Sanitize the Water Softener Addingsalttothe Storagetank Check List of STEP-BY-STEP Guides to Install 312 Nun @ Questions? Call The Kenmore Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener Fast Rinse Salt Bridge Iron from Resin BED Drain ALL Water from Softener Problemcause Bypass Valves Pressure Drop PSI vs. Flow Rate GPM Faceplate Procedure for Removing Error Code From Faceplate Sc,l Root sto Rotaryvalveservice Water Flow Through the Softener Valve Backwash Cycle Questions? Call The Kenmore Water Line LiO KeyNo Inlet Outlet Grounding Clamps Brine Valve Assembly 11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home

625.38306 specifications

The Kenmore 625.38306 is a standout model in the realm of home appliances, particularly known for its advanced air filtration and humidification capabilities. Designed with the modern homeowner in mind, this unit effectively blends functionality with ease of use.

One of the key features of the Kenmore 625.38306 is its powerful air purification system. Equipped with a high-efficiency particulate air (HEPA) filter, it captures up to 99.97% of airborne particles, including dust, pollen, pet dander, and smoke. This capability ensures that the air in your home is not only cleaner but also healthier for you and your family. The HEPA filter is designed for longevity, providing extended usage before needing to be replaced, which adds to the convenience.

In addition to its air purification prowess, the Kenmore 625.38306 also includes a built-in humidifier. This feature allows users to maintain optimal humidity levels in their home, which can be particularly beneficial during dry winter months. Proper humidity control can alleviate symptoms of dry skin, respiratory issues, and can even help protect wooden furniture and floors from cracking due to excessive dryness. The humidification technology operates quietly in the background, ensuring a peaceful environment.

The design of the Kenmore 625.38306 is both sleek and functional. With a user-friendly interface, it features intuitive controls that allow users to easily adjust settings. The digital display provides real-time feedback on indoor air quality, humidity levels, and filter status, ensuring users are well informed about their environment. Additionally, the compact design makes it versatile enough to fit in various room sizes, from bedrooms to living areas.

Energy efficiency is another notable characteristic of the Kenmore 625.38306. It is designed to operate at low power consumption levels without compromising performance, making it an environmentally friendly choice. This unit is also equipped with automatic shut-off and sleep modes to enhance energy savings while maintaining optimal air quality.

In summary, the Kenmore 625.38306 is a highly effective air purifier and humidifier that excels in delivering clean and healthy indoor air. With its advanced filtration system, convenient humidity control, user-friendly design, and energy efficiency, this model stands out as a reliable choice for anyone looking to enhance their home environment. Whether you have allergies, respiratory concerns, or simply want to create a more comfortable living space, the Kenmore 625.38306 provides the solution you need.
Top Page Image Contents