Kenmore 625.38306 owner manual Water Flow Through Softener Fast Rinse, Electronics

Page 27

FAST RINSE: Backwash is followed by a fast flow of water down through the resin tank. The fast flow packs the resin bed and gets it ready for return to service. See Fig. 40.

After fast rinse, the softener returns to service. Hard water goes into the resin tank where the resin bed again takes out the hardness minerals. Soft water goes to the house soft water pipes.

WATER FLOW THROUGH

THE SOFTENER

IN FAST RINSE

Soft Water Hard Water

OUT IN

SOFT WATER SERVICE AND REGENERATION

AUTOMATIC BYPASS

During the brining, brine rinse and backwash cycles of regeneration, HARD water goes through the softener valve and to the house pipes. If a faucet is opened, hard water is there for your needs. However, you should not use hot water, if possible, because the water heater will refill with hard water. The softener, as factory pro- grammed, regenerates from 2:00 AM to about 4:20 AM, a time when not much water is used.

If you start your day prior to 4 AM, you may need to change the recharge starting time. Set the recharge time to 12:00 AM or 1:00 AM. Then regeneration will start and end that much earlier and your water heater will not refill with hard water if a hot faucet is opened.

ELECTRONICS

Two main parts of the softener's electronics are: a WATER METER, and a COMPUTER.

•WATER METER The water meter is in the softener valve outlet. As water flows through the meter, it sends electric pulses to the computer. The computer changes the puls- es to a measure in gallons of water.

•COMPUTER The computer is part of the faceplate timer circuit board. It is programmed to know the softener's capacity (how many grains of hardness minerals it will take out of the water before a regeneration is needed). When starting the softener, you set it for the grains per gallon (gpg) hardness of the water.

To find a regeneration pattern best for your needs, the computer uses:

(1)water usage from the meter

(2)hardness setting

(3)softener capacity

(4)time since the last regeneration.

l-' l

FIG. 40

The computer always adjusts this pattern to your water using habits. It works toward providing you with soft water for the longest time and at the most efficient salt usage.

Softening capacity is used as hard water goes through the softener and hardness minerals are removed. When the computer determines that only enough capacity remains to provide soft water up to the next regenera- tion starting time (2:00 AM, or as otherwise set) it will schedule a regeneration. When the regeneration begins, RECHARGE NOW flashes in the display during the regeneration.

Questions? Call The Kenmore Water Line 1-800-426-9345

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Save this Manual Water SoftenerTEN Year Limited Warranty Against Leaks ONE Year Limited Warranty on Water SoftenerQuestions? Questions? Call The Kenmore Water Line Inspect Shipment Parts Descriptions SmallPipe Proper Order to Install Water Treating EquipmentPlan Your Installation Tools NeededWhere to Install the Water Softener Typical InstallationDraw Your Pipes Fittings Suggested Slab Foundation InstallationClip Adding a pressure reducing valve may reduce the flow Before Installing Checks & TestsAssemble Inlet Outlet ADAPTORS, or Single Bypass Valve Bypass ValveInlet and Outlet Threaded Adaptors Installing Holding Clips Valve BypassBypass Valve Turned Downward Connect the Softener Move Softener Into PlaceTypical Soldering Connections Position Softener Into PlaceConnect Salt Tank Overflow Tubing Connect the Valve Drain HoseHouse Main Water Shutoff Valves Single BypassLeak Test Cold Water Pipe Grounding Water Meter Jumper WireConnecting Transformer Electrical Power Outlet for Your SoftenerInstall Covers Install CoversRestart the Water Heater SET Present Time of DAY Program the TimerSET Salt Level SET Water Hardness NumberHardness Number SET Regeneration TimeSanitize Your Water Softener AS Follows Sanitize the Water SoftenerRemoving Additives Water Softening Salt with IronUnit plugged Into a continuously live outlet? Check List of STEP-BY-STEP Guides to InstallRecharge NOW Recharge TonightSalt Monitor System Efficiency Mode Error CodeProgram Memory Soft Water Service and Regeneration ServiceRegeneration Water Flow Through Softener in Backwash Water Flow Through Softener Brining and Brine RinseSoft Water Service and Regeneration Automatic Bypass Water Flow Through Softener Fast RinseElectronics Salt Bridge Salt BridgeIron from Resin BED Cleaning Nozzle & Venturi Keeping the Water Softener CleanProtect the Water Softener from Freezing Drain ALL Water from SoftenerProblemcause Checklist to Help YOU Save MoneyCorrection Bypass Valves Model no .383060 Timer Code SPressure Drop PSI vs. Flow Rate GPM Wiring Schematic Always Make These Initial Checks FirstEration Check Possible Problem Code Most Likely Less Likely Procedure for Removing Error Code From FaceplateManual Initiated Electronics Diagnostics Troubleshooting Valve Position Indicators Timer PWA ReplacementOther Information MAX. Fast Rinse Cycle Flow Rates Gallons PER MINBrine Rinse MAX. BackwashServicing the Valve DisassemblyAssembly To Relieve PressureBrining and Brine Rinse Cycle Valve Service CycleWater Flow Through the Softener Fill CycleFast Rinse Cycle Valve Backwash CycleFast Rinse Cycle Backwash CycleQuestions? Call The Kenmore Water Line LiO Water Softener Complete KeyNoInlet Outlet Grounding Clamps Key No. Part Number Part Description Brine Valve Assembly11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home Water Softener Warranty on Water Softener Questions? Questions? Call The Kenmore Water Line Parts Descriptions Small DeFa ce s Typical Installation Suggested Slab Foundation Installation Clip Before Installing Checks & Tests Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve Valve Bypass Move Softener Into Place Connect the Valve Drain Hose House Main Water Shutoff Valves Installgroundingclampbetween Thesoftenerinand OUT Pipes Install Covers PMI UP or Down button in changes the display twice each second Sanitize the Water Softener Addingsalttothe Storagetank Check List of STEP-BY-STEP Guides to Install 312 Nun @ Questions? Call The Kenmore Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener Fast Rinse Salt Bridge Iron from Resin BED Drain ALL Water from Softener Problemcause Bypass Valves Pressure Drop PSI vs. Flow Rate GPM Faceplate Procedure for Removing Error Code From Faceplate Sc,l Root sto Rotaryvalveservice Water Flow Through the Softener Valve Backwash Cycle Questions? Call The Kenmore Water Line LiO KeyNo Inlet Outlet Grounding Clamps Brine Valve Assembly 11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home

625.38306 specifications

The Kenmore 625.38306 is a standout model in the realm of home appliances, particularly known for its advanced air filtration and humidification capabilities. Designed with the modern homeowner in mind, this unit effectively blends functionality with ease of use.

One of the key features of the Kenmore 625.38306 is its powerful air purification system. Equipped with a high-efficiency particulate air (HEPA) filter, it captures up to 99.97% of airborne particles, including dust, pollen, pet dander, and smoke. This capability ensures that the air in your home is not only cleaner but also healthier for you and your family. The HEPA filter is designed for longevity, providing extended usage before needing to be replaced, which adds to the convenience.

In addition to its air purification prowess, the Kenmore 625.38306 also includes a built-in humidifier. This feature allows users to maintain optimal humidity levels in their home, which can be particularly beneficial during dry winter months. Proper humidity control can alleviate symptoms of dry skin, respiratory issues, and can even help protect wooden furniture and floors from cracking due to excessive dryness. The humidification technology operates quietly in the background, ensuring a peaceful environment.

The design of the Kenmore 625.38306 is both sleek and functional. With a user-friendly interface, it features intuitive controls that allow users to easily adjust settings. The digital display provides real-time feedback on indoor air quality, humidity levels, and filter status, ensuring users are well informed about their environment. Additionally, the compact design makes it versatile enough to fit in various room sizes, from bedrooms to living areas.

Energy efficiency is another notable characteristic of the Kenmore 625.38306. It is designed to operate at low power consumption levels without compromising performance, making it an environmentally friendly choice. This unit is also equipped with automatic shut-off and sleep modes to enhance energy savings while maintaining optimal air quality.

In summary, the Kenmore 625.38306 is a highly effective air purifier and humidifier that excels in delivering clean and healthy indoor air. With its advanced filtration system, convenient humidity control, user-friendly design, and energy efficiency, this model stands out as a reliable choice for anyone looking to enhance their home environment. Whether you have allergies, respiratory concerns, or simply want to create a more comfortable living space, the Kenmore 625.38306 provides the solution you need.
Top Page Image Contents