Kenmore 625.38306 owner manual Sc,l

Page 84

TROUBLESHOOTING

VALVE POSITION INDICATORS:

Depending on the valve position, the following indica- tors show in the display:

Indicator

Valve Position

Serv

Service

Fill

Fill

Brine

Brining/Brine Rinse

Bkwsh

Backwash

Rinse

Fast Rinse

When the valve is rotating from one cycle to another, both indicators flash. For example, if the valve is in transition between fill and brining, both Fill and Brine flash. Upon reaching brining position, Fill goes off and Brine is on steady. The time display shows the minutes of the cycle remaining.

NOTE: If the faceplate is left in a diagnostic display (or a flashing display when setting times or hard- ness), present time automatically returns if a button is not pressed within 4 minutes. To return to the diagnostic display, repeat step 1.

OTHER INFORMATION

While in this diagnostic screen, the following information is available and may be beneficial for various reasons. This information is retained by the computer from the first time electrical power is applied to the faceplate.

•Press and hold the UP button to display the number of days this faceplate has had electrical power applied.

•Press and hold the DOWN button to display the num- ber of regenerations initiated by this faceplate since the model code number was entered.

•Press the REGENERATION button to advance the valve to each position and observe the switch and position indicators to verify component operation, or to possibly isolate a defect.

•Press and hold the SELECT button for 3 seconds until a model code shows in the display, see Fig. 51.

This code identifies the softener nominal capacity size. If the wrong model code shows, the softener will operate on incorrect data. Do the following as needed.

If the correct model code (S 25) shows: Press the SELECT button to return to the present time display.

To change the number: Press the UP or DOWN but- ton until the correct model code (S 25) shows. Then, press the SELECT button and reset the timer.

OUT

Positionmarkers

(Valveinservice)

O

MOTOR

O

FIG. 50

TIMER PWA REPLACEMENT

Be sure the valve is in service position when replacing the timer PWA (observe valve cycle indi- cator). If after installing and programming the replace- ment timer PWA, the valve is not in service position, do the following to assure correct cycle orientation, or tim- ing, between the faceplate and valve.

Use the MANUAL ADVANCE procedures with the REGENERATION button, advance through the recharge cycles until the valve stops in service position, and RECHARGE no longer flashes in the display.

NOTE: The valve motor may automatically drive through several valve positions while searching for service. If an error code occurs, unplug the trans- former, then plug in again.

CODE1

Sc:,l

FIG. 51

Questions? Call The Kenmore Water Line 1-800-426-9345

36

Page 83 Page 85
Image 84
Page 83 Page 85
Contents Water Softener Save this ManualONE Year Limited Warranty on Water Softener TEN Year Limited Warranty Against LeaksQuestions? Questions? Call The Kenmore Water Line Parts Descriptions Small Inspect ShipmentProper Order to Install Water Treating Equipment Plan Your InstallationTools Needed PipeTypical Installation Where to Install the Water SoftenerSuggested Slab Foundation Installation Draw Your Pipes FittingsClip Before Installing Checks & Tests Adding a pressure reducing valve may reduce the flowAssemble Inlet Outlet ADAPTORS, or Single Bypass Valve Bypass ValveInlet and Outlet Threaded Adaptors Installing Holding Clips Valve BypassBypass Valve Turned Downward Move Softener Into Place Typical Soldering ConnectionsPosition Softener Into Place Connect the SoftenerConnect the Valve Drain Hose Connect Salt Tank Overflow TubingHouse Main Water Shutoff Valves Single BypassLeak Test Water Meter Jumper Wire Connecting TransformerElectrical Power Outlet for Your Softener Cold Water Pipe GroundingInstall Covers Install CoversRestart the Water Heater Program the Timer SET Present Time of DAYSET Water Hardness Number Hardness NumberSET Regeneration Time SET Salt LevelSanitize the Water Softener Sanitize Your Water Softener AS FollowsWater Softening Salt with Iron Removing AdditivesCheck List of STEP-BY-STEP Guides to Install Unit plugged Into a continuously live outlet?Recharge NOW Recharge TonightSalt Monitor System Efficiency Mode Error CodeProgram Memory Soft Water Service and Regeneration ServiceRegeneration Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener in BackwashSoft Water Service and Regeneration Automatic Bypass Water Flow Through Softener Fast RinseElectronics Salt Bridge Salt BridgeCleaning Nozzle & Venturi Keeping the Water Softener Clean Iron from Resin BEDDrain ALL Water from Softener Protect the Water Softener from FreezingProblemcause Checklist to Help YOU Save MoneyCorrection Model no .383060 Timer Code S Bypass ValvesPressure Drop PSI vs. Flow Rate GPM Wiring Schematic Always Make These Initial Checks FirstEration Check Possible Problem Code Most Likely Less Likely Procedure for Removing Error Code From FaceplateManual Initiated Electronics Diagnostics Troubleshooting Valve Position Indicators Timer PWA ReplacementOther Information Cycle Flow Rates Gallons PER MIN Brine RinseMAX. Backwash MAX. Fast RinseDisassembly AssemblyTo Relieve Pressure Servicing the ValveValve Service Cycle Water Flow Through the SoftenerFill Cycle Brining and Brine Rinse CycleValve Backwash Cycle Fast Rinse CycleBackwash Cycle Fast Rinse CycleQuestions? Call The Kenmore Water Line LiO KeyNo Water Softener CompleteInlet Outlet Grounding Clamps Brine Valve Assembly Key No. Part Number Part Description11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home Water Softener Warranty on Water Softener Questions? Questions? Call The Kenmore Water Line Parts Descriptions Small DeFa ce s Typical Installation Suggested Slab Foundation Installation Clip Before Installing Checks & Tests Assemble Inlet Outlet ADAPTORS, or Single Bypass Valve Valve Bypass Move Softener Into Place Connect the Valve Drain Hose House Main Water Shutoff Valves Installgroundingclampbetween Thesoftenerinand OUT Pipes Install Covers PMI UP or Down button in changes the display twice each second Sanitize the Water Softener Addingsalttothe Storagetank Check List of STEP-BY-STEP Guides to Install 312 Nun @ Questions? Call The Kenmore Water Flow Through Softener Brining and Brine Rinse Water Flow Through Softener Fast Rinse Salt Bridge Iron from Resin BED Drain ALL Water from Softener Problemcause Bypass Valves Pressure Drop PSI vs. Flow Rate GPM Faceplate Procedure for Removing Error Code From Faceplate Sc,l Root sto Rotaryvalveservice Water Flow Through the Softener Valve Backwash Cycle Questions? Call The Kenmore Water Line LiO KeyNo Inlet Outlet Grounding Clamps Brine Valve Assembly 11 10 Wear-Strip Seal Cross-Section View No. Number Part Description Your Home

625.38306 specifications

The Kenmore 625.38306 is a standout model in the realm of home appliances, particularly known for its advanced air filtration and humidification capabilities. Designed with the modern homeowner in mind, this unit effectively blends functionality with ease of use.

One of the key features of the Kenmore 625.38306 is its powerful air purification system. Equipped with a high-efficiency particulate air (HEPA) filter, it captures up to 99.97% of airborne particles, including dust, pollen, pet dander, and smoke. This capability ensures that the air in your home is not only cleaner but also healthier for you and your family. The HEPA filter is designed for longevity, providing extended usage before needing to be replaced, which adds to the convenience.

In addition to its air purification prowess, the Kenmore 625.38306 also includes a built-in humidifier. This feature allows users to maintain optimal humidity levels in their home, which can be particularly beneficial during dry winter months. Proper humidity control can alleviate symptoms of dry skin, respiratory issues, and can even help protect wooden furniture and floors from cracking due to excessive dryness. The humidification technology operates quietly in the background, ensuring a peaceful environment.

The design of the Kenmore 625.38306 is both sleek and functional. With a user-friendly interface, it features intuitive controls that allow users to easily adjust settings. The digital display provides real-time feedback on indoor air quality, humidity levels, and filter status, ensuring users are well informed about their environment. Additionally, the compact design makes it versatile enough to fit in various room sizes, from bedrooms to living areas.

Energy efficiency is another notable characteristic of the Kenmore 625.38306. It is designed to operate at low power consumption levels without compromising performance, making it an environmentally friendly choice. This unit is also equipped with automatic shut-off and sleep modes to enhance energy savings while maintaining optimal air quality.

In summary, the Kenmore 625.38306 is a highly effective air purifier and humidifier that excels in delivering clean and healthy indoor air. With its advanced filtration system, convenient humidity control, user-friendly design, and energy efficiency, this model stands out as a reliable choice for anyone looking to enhance their home environment. Whether you have allergies, respiratory concerns, or simply want to create a more comfortable living space, the Kenmore 625.38306 provides the solution you need.
Top Page Image Contents