Eaton Electrical Magnum Transfer Switch manual Automatic Transfer Switch

Page 21

Instructional Booklet

Fixed and Drawout Magnum Transfer Switches

Effective: March 2007

Page 21

Figure 24. Close Switch by Pushing Close Button.

NOTICE

IF A TRANSFER SWITCH WITH ANY TYPE OF ELECTRICAL OPERAT- ING CAPABILITIES IS TO BE OPERATED MANUALLY UTILIZING THE MANUAL OPERATING HANDLE, IT IS STRONGLY RECOMMENDED THAT THE TRANSFER CONTROL CIRCUIT FIRST BE ISOLATED. THIS IS ACCOMPLISHED BY DISCONNECTING THE S7/P7 PLUG ON THE TRANSFORMER PANEL. AN AUTOMATIC ENGINE START WILL OCCUR UNLESS THE GENERATOR RUN SWITCH SET TO “OFF.” IF,

HOWEVER, A TRANSFER SWITCH IS SUPPLIED WITH A FOUR-POSI- TION SELECTOR SWITCH (OPTION 6H), IT CAN BE TURNED TO THE OFF POSITION, MAKING IT UNNECESSARY TO UNPLUG THE LOGIC. IN THE CASE OF THE ATS DESIGN, ANY ATTEMPT TO OPERATE THE MANUAL HANDLE WITHOUT FIRST ISOLATING THE CONTROL CIRCUIT CAUSES AN AUTOMATIC TRANSFER.

5.2 Automatic Transfer Switch

The operating sequence of an ATS is dictated by the switch’s standard features and selected options. Operation of an ATS dur- ing Source 1 power source failure, Source 1 power source restora- tion, and testing is described in the associated Controller Instruction Booklet.

WARNING

OVERLAPPING CONTACTS

SOURCE 1 AND SOURCE 2

must be Synchronized

7805C60H04

THIS PRODUCT CONTAINS A SPECIAL CON- TACT ARRANGEMENT (OVERLAPPING CON- TACTS). MISUSE CAN RESULT IN DEATH SEVERE PERSONAL INJURY OR PROPERTY DAMAGE.

(THIS LABEL IS APPLIED TO THE DOOR )

Do Not Use Without FOLLOW THE INSTRUCTIONS

Reading Manual

Operating Instructions OUTLINED IN THE NEXT

WARNING LABEL.

MANUAL CLOSE BUTTON (THIS LABEL IS APPLIED TO THE COVER OF THE MANUAL CLOSE BUTTON ON EACH

WARNING

Attempting to close both switching devices simultaneously can cause severe injury

or death.

Follow Manual Operation Instructions Below

Manual Operation Instructions

1.Disconnect Logic Connectors

2.Open both switching devices

3.Verify "OPEN" flags

4.Verify source availability

5.Close switching device on available source

7805C60H05

THESE INSTRUCTIONS ONLY PERTAIN TO MANUALLY CLOSING A SINGLE SWITCHING DEVICE. ATTEMPTING TO CLOSE BOTH SWITCHING DEVICES CAN CAUSE SEVERE INJURY OR DEATH.

THIS LABEL IS APPLIED TO THE DOOR.

Figure 25. Switching Device Closing Precautions (Closed Transition Only).

IB01602011E

For more information visit: www.Eaton.com

Image 21 Contents
Testing and Problem Solving Maintenance Renewal Parts Guide Manual for the Fixed and Drawout Magnum Transfer SwitchesInstructional Booklet Preliminary Comments and Safety Precautions IntroductionGeneral Information Design Configuration Typical Load Transfer Switch Switching Device Type SchematicWithstand Ratings Typical Bypass Isolation Switch SchematicMagnum Fixed and Drawout Switching Devices Magnum Transfer Switch ConfigurationsGeneral Magnum Switching Device Fixed Switching Device for the Magnum Transfer Switch Transfer Switch Catalog Number Identification Transfer Switch Catalog Number Explanation Using the Style Identification GuideEquipment Description Receiving, Handling, and StoragePower Panel Switch Interlocks Open Transition OnlyDrawout Interlocks Left Side View with Panels Removed Voltage Selection Panel Logic PanelDrawout Mechanism Features NeutralsRelay Auxiliary Contacts Enclosure Transfer Switch Equipment EnclosuresInstallation and Wiring StandardsMounting Location Seismic Tested and Approved Product Mounting Instructions Unpackaging and Inspection Mounting ProcedureWire Size for Available Power Cable Connections Power Cable ConnectionsMounting the Switching Device in the Drawout Mechanism Voltage Selection AdjustmentWiring OperationEngine Start Connection Close Switch by Pushing Close Button Automatic Transfer SwitchDrawout and Fixed Switching Devices Installing a Drawout Switching DeviceSwitching Device Positioning Switching Device in the Connect Position Levering and Position Indication Fixed Switching DeviceOperation of the Bypass Isolation Transfer Switch Switching Device OperationOperator Panel Automatic Operation Bypassing the Transfer SwitchSource 1 to Source 1 Bypass Source 2 to Source 2 BypassInto Its Source 2 to Source 1 Bypass Open Transition Only Manual Operation When in Bypass Mode Testing and Problem SolvingTesting Problem SolvingTransfer Switch Appears Inoperative Transfer Switch Will Not Automatically Transfer to SourceTransfer Switch Will Not Automatically Recharge Switches Periodic Maintenance Procedures MaintenanceMaintenance Procedures IntroductionCover Removal and Replacement Cover Removal and ReplacementRenewal Parts Guide Instructional Booklet Sensing Harness TSMGH02 Kcmil Neutral Terminal Instructional Booklet