Mitsubishi Electronics MSZ-FA25VA E1 MSZ-FA35VA E1 Accessories, Remote Controller

Page 4

MSZ-FA25VA - E1 MSZ-FA35VA - E1

ACCESSORIES

 

 

MSZ-FA25VA - E1

 

 

MSZ-FA35VA - E1

 

 

 

1

Installation plate

1

 

 

 

2

Installation plate fixing screw 4 o 25 mm

5

 

 

 

3

Remote controller holder

1

 

 

 

4

Fixing screw for 3 3.5 o 1.6 mm (Black)

2

 

 

 

5

Battery (AAA) for remote controller

2

 

 

 

6

Wireless remote controller

1

 

 

 

7

Felt tape (Used for left or left-rear piping)

1

REMOTE CONTROLLER

Signal transmitting section

Operation display section

OPERATE/STOP (ON/OFF) button

Open the front lid.

FAN SPEED CONTROL button

OPERATION SELECT button

ECONO COOL button

PLASMA button

AREA button

i-see button RESET button

Temperature buttons

Indication of remote controller model is on back

WIDE VANE button (Vertical vane button)

OFF-TIMER button

ON-TIMER button

TIME SET buttons

FORWARD button

BACKWARD button

CLOCK SET button

VANE CONTROL button (Horizontal vane button)

4

Image 4
Contents Contents MSZ-FA25VA E1 MSZ-FA35VA E1Generalized stepping motor Technical ChangesFront panel opening/closing output gear Wash reset switch Open Closed Receiving section Part Names and FunctionsIndoor Unit MSZ-FA25VA MSZ-FA35VA See control operationMSZ-FA25VA E1 MSZ-FA35VA E1 Accessories Remote ControllerSpecifications and rating conditions of main electric parts SpecificationWhen outdoor unit is MXZ type MSZ-FA25VA E1 Noise Criteria CurvesMSZ-FA35VA E1 Outlines and Dimensions MSZ-FA25VA E1 MSZ-FA35VA E1Indoor Unit Unit mmWiring Diagram Refrigerant System DiagramMSZ-FA25VA E1 Indoor Unit MSZ-FA35VA E1 Indoor UnitService Functions How to modify the remote controller P.C. boardRemote controller model KM05A OperationRemote controller Troubleshooting Install RemoveInformation for Multi System AIR Conditioner Outdoor Unit MXZ seriesFailure mode recall function OFFTo identify the error.Refer to 9-6.For G Indoor unit failure mode table Plasma DeodorizingPlasma AIR Purifying OFFInstruction of troubleshooting StartTroubleshooting check table · Flashing of Power lamp indicates abnormalitiesAIR PlasmaPurifying Trouble criterion of main parts When Power lamp flashes 3-time Indoor fan does not operate Troubleshooting flowCheck of indoor fan motor Check of remote controller and receiver P.C. board Indoor electronic control P.C.Board How to check mis-wiring and serial signal error LEDCheck of installation of the horizontal vane Safety Deviceplasma Unit Plasma Deodorizing 0V?Continuously flash? AIR Purifying 0V?Check of auto front panel Indoor unit and outdoor unit do not operateElectromagnetic noise enters into TV sets or radios YesTest point diagram and voltage Power monitor receiver P.C. boardPlasma power P.C. board Indoor electronic control P.C. boardDisassembly Instructions Removing the panel PhotoOperating Procedure Photos Removing the electrical boxRemoving the horizontal vane motor unit Photo Removing the vertical vane motor unit PhotoRemoving the indoor fan motor and the line flow Photo FanRemoving the plasma power P.C. board Photo Parts List Accessory and Remote ControllerSafety Plasma Indoor Unit Electrical Parts and Functional PartsIndoor Unit Heat Exchanger Motor Receiver P.C Board HolderSymbol Qty/unit Part name Wiring Diagram E02509 504Optional Parts Deodorizing Ceramic FilterPage Specifications subject to change without notice