Electrolux D4100 HOW to Finish Unpacking, Tools Required, Making the Electrical Connections

Page 46

HOW TO FINISH UNPACKING

Place packed cooker next to the cabinet in which it will be installed.

Remove the cooker packing except for bottom tray which should be left in position until the cooker is ready to be fitted into its cabinet.

It is imperative that the cooker is left in the base to protect both the appliance and the floor.

Ensure the user is given these operating instructions.

TOOLS REQUIRED

The following tools will be needed and it helps to assemble them before starting to install the oven:-

A terminal screwdriver (3mm wide blade)

A pozidrive screwdriver

Pliers

Wirestrippers

Knife

Sidecutters

Adhesive Tape

Tape Measure

MAKING THE ELECTRICAL

CONNECTIONS

Important: Switch off at mains,

miniature circuit breaker and, if appropriate, remove fuse before commencing any electrical work

PREPARING CABLE

We recommend you use a new length of cable to ensure your safety.

Ensure you have the correct length of cable appropriate to the wiring method you are using. When fitting new cable allow sufficient cable for removal of the unit at a later date, should it be necessary.

Score, but do not cut through, around the sheathing with a knife 100mm (4in) from each end of the cable and break through to the encased wires by bending the cable backwards and forwards to fatigue the sheathing.

Carefully score down from each end of the cable sheathing along the length of the bare earth wire (if a cut was made along the length of the live and neutral wires, it might cut into their sheathing) to the cuts already made.

Carefully prise open the sheathing at each end of the cable to expose the encased wiring.

45

Image 46

Contents Competence D4100 Important Safety Information Contents Description of the Oven Getting to Know Your Oven Control PanelGrill and Oven Furniture Before Using the Oven for the First Time SET the Time of DAY Electronic TimerMinute Minder HOW to SET the Oven Timer Control To Cancel the Minute MinderTo SET the Timer to Switch on and OFF Automatically To Cancel AN Automatic Programme To SET the Timer to Switch OFF onlyTo Return the Cooker to Manual LTHINGS to Note Automatic CookingUsing the Telescopic Runners Using the GrillDual Grill Grill PAN and Handle Hints and TipsGrilling Chart Food Grill TimeSecond Oven Using the Second OvenTo FIT the Second Oven Shelf Hints and Tips Second Oven Cooking Chart FoodMain FAN Oven LHINTS and Tips Using the Conventional Oven Conventional OvenHints and Tips Oven Cooking Chart FAN Oven ConventionalInternal Temperatures Roasting ChartRoasting Chart Meat SECOND/FAN Cooking Time OvenUsing Pizza Function Pizza FunctionSpeedcook Using SpeedcookCooking Times Hints and Tips Using Thermal Grilling Thermal GrillingThermal Grilling Chart Food Shelf TempUsing Defrost Feature DefrostingPage Helpful Hints When Buying and Preparing Food Meat TemperaturesCleaning the Outside of the Oven Care and CleaningCleaning Materials Removing and Replacing Wirework Side RunnersCleaning the Door Glass Cleaning Inside the OvensTo Remove the Inner Glass Cleaning the Grill and Oven Furniture To Clean the Inner Glass Door PanelsTo Replace the Inner Glass Panel Replacing AN Oven Light Bulb Problem If Something Doesnt WorkOven light fails to illuminate Guarantee Conditions European GuaranteeAEG Service and Spare PartsCustomer Care Department SL1 1DZAEG Service Centres Midlands LO on & East Anglia South East South West Installation Instructions Technical DetailsChoice of Electrical Connection Preparing Cabinet for Fitting of Oven Do not lift the appliance by the handlesCross section Making the Electrical Connections HOW to Finish UnpackingTools Required Preparing CableTo Remove Cover of Mains Terminal Connecting to a HOB or Cooker Point Connecting to Mains TerminalChecking Electrical Connections Fitting Into the Cabinet Appliance by the handlesCompetence D4100 Rating Plate Reference Telephone 0870 5