KitchenAid LI3ZFE/W10321799F Location Requirements, Parts Supplied, For Mobile Home Installations

Page 4

For Non-Vented (Recirculating) Installations, You Will Also Need:

Recirculating Kit Part Number W10272061 for non-vented (recirculating) installations only. See “Assistance or Service” section to order.

6" (15.2 cm) round metal vent duct. Length required is determined by ceiling height.

Parts Supplied

Remove parts from packages. Check that all parts are included.

Hood canopy assembly with ventilator and light bulbs installed

Filter—installed in hood canopy

4 x 8 mm screws (68)

5 x 45 mm screws (4)

Mounting template

Vent covers (4)

Vent transition with backdraft damper installed

2 - 3.5 x 9.5 mm mounting screws

4 - Plastic vent clips

Upper horizontal support bracket

Horizontal support

8 - Vertical supports

2 - Vent cover supports

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the left filter on the rear wall of the vent hood.

Canopy hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Requirements” section.

Because of the size and weight of this island hood, the chimney support must be securely attached to the ceiling.

For plaster or drywall ceilings, the chimney support must be attached to joists. If this is not possible, you must build a support structure behind the plaster or drywall. The support structure must be able to support 80 lbs (36.6 kg).

The range hood is factory set for venting through the roof.

For non-vented (recirculating) installation see “Non-Vented (recirculating) Installation” in “Install Range Hood” section. Recirculation Kit Part Number W10272061 is available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

12¹⁄₄"

(31.0 cm)

13³⁄₁₆"

(33.5 cm)

*32¹⁄₂"

(82.6 cm)

min. **32¹⁄₂" *46¹⁄₂" (82.6 cm)

(118.0 cm) min.

max. **52⁹⁄₁₆" (133.5 cm)

max.

36" (91.2 cm)

or

27" (68.6 cm)

42" (106.4 cm)

*Vented installations only

**Non-vented (recirculating) installations only

Installation Dimensions

B

CA

D

A. Ceiling height

B. Hood height from ceiling to bottom of the range hood: A-C-D=B

C. 24" (61.0 cm) minimum to 36" (91.4 cm) maximum suggested hood height.

D. Countertop height

IMPORTANT:

Minimum distance “C”: 24" (61.0 cm) from electric cooking surface.

Minimum distance “C”: 27" (68.6 cm) from gas cooking surface.

Suggested maximum distance “C”: 36" (91.4 cm)

4

Image 4
Contents Island Canopy Range Hood Range Hood Safety Table of ContentsTable DES Matières Installation Requirements For Vented Installations, You Will Also NeedTools and Parts Tools NeededFor Mobile Home Installations Product DimensionsInstallation Dimensions Location RequirementsVenting Requirements Installation Instructions Range Hood Mounting Screws InstallationElectrical Requirements Prepare LocationComplete Preparation Assemble and Install Range HoodConnect Vent System Non-Vented Recirculating Installation Make Electrical ConnectionInstall Duct CoversComplete Installation Range Hood USETimer DisplayLight Fan SpeedCleaning Range Hood CareWiring Diagram Motor SpecificationsAssistance or Service AccessoriesU.S.A CanadaKitchenaid Ventilation Warranty This limited warranty does not coverSécurité DE LA Hotte DE Cuisinière Votre sécurité et celle des autres est très importanteImportantes Instructions DE Sécurité Exigences d’emplacement Exigences D’INSTALLATIONOutils et pièces Dimensions du produit Dimensions d’installationInstallations dans une région à climat froid Exigences concernant l’évacuationSpécifications électriques Instructions D’INSTALLATION Préparation de l’emplacementInstallation des vis de montage de la hotte Terminer la préparationAssemblage et installation de la hotte Raccordement du circuit d’évacuationRaccordement électrique Installation des cache-conduits Achever l’installationTableau de commande Utilisation DE LA HotteAffichage ÉclairageMinuterie Vitesse du ventilateurEntretien DE LA Hotte NettoyageSchéma DE Câblage Caractéristiques du moteurAccessoires Assistance OU ServiceAu Canada La présente garantie limitée ne couvre pas Garantie DU Système DE Ventilation KitchenaidW10321799F