Siemens HE2425(U, HE2528U, C), HE2224(U installation instructions Connect Electric

Page 11

Installation

Electrical connection

(found behind terminal block cover)

Feed range cord through strain relief in knockout panel here.

Figure 4: Electrical Connection and Strain Relief Knockout Panel Locations

Connect Electric

There are four possible electrical connections:

1.Four (4) wire range cord

2.Three (3) wire range cord

3.Four (4) wire flexible conduit connection (hard wire)

4.Three (3) wire flexible conduit connection (hard wire)

The four wire range cord connection is the recommended method, but where local codes permit, three wire connections are also acceptable.

As an alternative to the range cord, the appliance can also be hard wired with either a three or four wire connection. In this case, the terminal lugs supplied must be used.

Always verify that your chosen connection complies with all applicable codes. Table 1, “Electrical Specifications,” on page 6.

WARNING:

To prevent electrical shock, the grounding prong on the range cord should not be cut or removed under any circumstances. It must be plugged into a matching grounding type receptacle and connected to a correctly polarized 240- Volt circuit. If there is any doubt as to whether the wall receptacle is properly grounded, have it checked by a qualified electrician.

WARNING:

Risk of Electric Shock or Fire. Frame grounded to neutral through a ground strap. Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC), mobile homes, and recre- ational vehicles, or in an area where local codes prohibit grounding through the neutral conductor.

For installations where grounding through the neutral conductor is prohibited, (a) disconnect the link from the neutral, (b) use grounding terminal or lead to ground unit, (c) connect neutral terminal to lead branch circuit neutral in usual manner

English 7

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Siemens Electric Range with threeD Surround Convection Page Table of Contents Page Important Safety Instructions SafetyImportant Safety Instructions Grounding Instructions Power Requirements and ElectricalDo not Lift Range by Door Handle Cabinet Requirements InstallationBefore You Begin Parts IncludedCooktop Clearances General Information Verify that wiring to house is adequateVerify that wiring inside house is adequate Installation Procedure Connect Electric Grounding Options Four Wire Range Cord Connection Recommended MethodFour Wire Range Cord Connection Ground Strap and Wire Terminal Block Appropriate Torque Levels for Aluminum or Copper Wire Four Wire Flexible Conduit Connec- tionCompleted Four Wire Flexible Conduit Connection Three Wire Flexible Conduit Con- nectionRange Tipping Hazard Anti-tip BracketAttach anti-tip bracket to floor Adjusting the Leg Support Page Product Data Plate ServicePage Table des matières Codes de sécurité et données tech- niques SécuritéInstructions de sécurité importantes Instructions de sécurité importantesTions de mise à la terre NE PAS Soulever L’APPAREIL PAR LA PoignéeExigences d’alimentation et instruc Pièces comprises Avant de commencerOutils et pièces néces- saires Dégagements de la surface de cuisson Dégagements requis’assurer que le câblage intérieur est adéquat Exigences électriquesGénéralités ’assurer que le câblage à la résidence est adéquatDonnées techniques électriques Procédure dinstallationConnexion électrique Connexion à 4 fils conducteur de terre et fil Connexion du cordon à 4 fils méth- ode recommandéeConnexion à 4 fils suite Connexion à 3 fils Connexion de conduit flexible à 4 filsNiveau de force approprié pour fil aluminium ou cuivre Dégainer le filConnexion de conduit flexible à 3 fils Risque DE Bascule DE LA Cuisinière Installer la fixation anti bascule au plancherAnti bascule Réglage des pieds Compléter l’installationPlaque signalétique Avant deffectuer un appel de serviceContenidos Requerimientos de seguridad del SeguridadInstrucciones Importantes de Seguridad Códigos de seguridad y especifica- cionesNunca Levante LA Estufa POR LA Agarradera DE LA Puerta Requerimientos para los gabinetes InstalaciónAntes de comenzar Partes incluidasEspacios libres para la estufa Espacios libres requeri- dosVerificar que el cableado dentro de la casa sea el adecuado Requerimientos eléctri- cosInformación general Verificar que el cableado a la casa sea el adecuadoPreparar las paredes y los pisos Tabla 1 Especificaciones eléctricasConsejos de instalación Instalar la ventilaciónConexión eléctrica Conexión del cable de 4 hilos Tira y cable de tierra Conexión del cable con cuatro hilos método recomendadoCentral Conexión del cable con tres hilosConexión de 3 hilos Conexión con cable flexible de cua- tro hilosNiveles correctos de torque para cable de aluminio o cobre Pelar el cableConexión con cable flexible de tres hilos Riesgo DE Volcadura DE LA Estufa AntivolcaduraFijar el soporte antivolcadura al piso Ajustar los soportes de las patas Terminar la instalaciónPlaca con datos del pro- ducto ServicioAntes de llamar al servicio Page

HE2224(U, HE2528U, C), HE2425(U specifications

The Siemens HE2224(U, HE2528U, C) and HE2425(U) models are a testament to Siemens' commitment to innovation and efficiency in the world of electrical engineering and automation. These units offer a range of advanced features, ensuring versatility and reliability for various applications.

The HE2224(U) series is designed to deliver exceptional performance and efficiency. One of its main features is the integration of advanced communication protocols, allowing for seamless connectivity and control within an automated system. This ensures efficient data exchange and remote monitoring, making it ideal for industries seeking to optimize their processes.

Additionally, the HE2528U model is equipped with a powerful processing unit that can handle complex algorithms and real-time data analyses. This capability significantly enhances operational speed and accuracy, allowing businesses to make informed decisions quickly and efficiently. The device’s robust design also reflects Siemens' dedication to durability and longevity, ensuring that it can withstand challenging environmental conditions.

The HE2425(U) model stands out with its emphasis on energy efficiency. It incorporates cutting-edge technologies that minimize power consumption without compromising performance. This focus on sustainability aligns with global efforts to reduce energy usage and carbon footprints in industrial operations.

These models feature user-friendly interfaces that simplify programming and operation. Enhanced visualization capabilities allow users to easily monitor system performance and make adjustments as needed. This accessibility is crucial for industries that require quick adaptations to changing conditions or requirements.

Safety is another critical aspect of these units. Siemens has integrated multiple safety features, including overload protection and fault detection systems, to safeguard both equipment and personnel. This commitment to safety enhances the overall reliability of the systems, making them suitable for various industrial applications.

In summary, the Siemens HE2224(U, HE2528U, C) and HE2425(U) models represent the forefront of technological advancements in industrial automation. With their robust performance, energy efficiency, advanced communication capabilities, and focus on safety, these units provide remarkable solutions for businesses aiming to enhance productivity while prioritizing sustainability. Siemens continues to set the benchmark in electrical engineering, ensuring that their products meet the evolving needs of various industries.
Top Page Image Contents