Siemens HE2224(U, HE2528U, C), HE2425(U installation instructions Adjusting the Leg Support

Page 18

Installation

•A risk of tip-over may exist if the appliance is not installed in accordance with these instructions.

•If the range is pulled away from the wall for cleaning, service, or any other rea- son, insure that the Anti-Tip Device is properly reengaged when the range is pushed back against the wall. In the event of abnormal usage (such as a person standing, sitting, or leaning on an open door), failure to take this precaution could result in tipping of the range. Personal injury might result from spilled hot liquids or from the range itself.

1.Adjust height of range and level by rotating the adjustable leg supports on the bottom of the range, using 1-1/4 inch (31.75 mm) wrench. See Figure 2: Adjusting the Leg Support.

drawer

wrench

adjustable leg

Figure 2: Adjusting the Leg Support

3.Measure to locate bracket position as shown in Figure 4: Anti-tip Bracket Location.

 

rearwall

cabinet wall

9/16" (14.29 mm)

 

from rear wall to center of screw hole

 

floor

 

anti-tippin g

 

device

 

flush against

 

cabinet wall

Figure 4: Anti-tip Bracket Location

5.Secure bracket with 2 screws (not included) that are adequate for mounting surface. (i.e.; for wood floor use wood screws for concrete floor use concrete anchors and screws).

Complete the Installation 1. Move range close enough to the opening to plug into the receptacle.

2.Slide range into position insuring that the left back leg slides under the anti-tip bracket. Range will sit 3/4” (19.05 mm) away from back wall when properly installed.

3.Carefully tip range forward to insure that the anti-tip bracket engages the range back brace and prevents tip-over.

4.Turn on electrical power. Check range for proper operation as described in Use and Care Manual.

English 14

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Siemens Electric Range with threeD Surround Convection Page Table of Contents Page Safety Important Safety InstructionsImportant Safety Instructions Power Requirements and Electrical Do not Lift Range by Door HandleGrounding Instructions Parts Included InstallationBefore You Begin Cabinet RequirementsCooktop Clearances Verify that wiring to house is adequate Verify that wiring inside house is adequateGeneral Information Installation Procedure Connect Electric Four Wire Range Cord Connection Recommended Method Grounding OptionsFour Wire Range Cord Connection Ground Strap and Wire Terminal Block Four Wire Flexible Conduit Connec- tion Appropriate Torque Levels for Aluminum or Copper WireThree Wire Flexible Conduit Con- nection Completed Four Wire Flexible Conduit ConnectionAnti-tip Bracket Attach anti-tip bracket to floorRange Tipping Hazard Adjusting the Leg Support Page Service Product Data PlatePage Table des matières Instructions de sécurité importantes SécuritéInstructions de sécurité importantes Codes de sécurité et données tech- niquesNE PAS Soulever L’APPAREIL PAR LA Poignée Exigences d’alimentation et instrucTions de mise à la terre Avant de commencer Outils et pièces néces- sairesPièces comprises Dégagements requis Dégagements de la surface de cuisson’assurer que le câblage à la résidence est adéquat Exigences électriquesGénéralités ’assurer que le câblage intérieur est adéquatProcédure dinstallation Données techniques électriquesConnexion électrique Connexion du cordon à 4 fils méth- ode recommandée Connexion à 4 fils conducteur de terre et filConnexion à 4 fils suite Connexion de conduit flexible à 4 fils Connexion à 3 filsDégainer le fil Niveau de force approprié pour fil aluminium ou cuivreConnexion de conduit flexible à 3 fils Installer la fixation anti bascule au plancher Anti basculeRisque DE Bascule DE LA Cuisinière Compléter l’installation Réglage des piedsAvant deffectuer un appel de service Plaque signalétiqueContenidos Códigos de seguridad y especifica- ciones SeguridadInstrucciones Importantes de Seguridad Requerimientos de seguridad delNunca Levante LA Estufa POR LA Agarradera DE LA Puerta Partes incluidas InstalaciónAntes de comenzar Requerimientos para los gabinetesEspacios libres requeri- dos Espacios libres para la estufaVerificar que el cableado a la casa sea el adecuado Requerimientos eléctri- cosInformación general Verificar que el cableado dentro de la casa sea el adecuadoInstalar la ventilación Tabla 1 Especificaciones eléctricasConsejos de instalación Preparar las paredes y los pisosConexión eléctrica Conexión del cable con cuatro hilos método recomendado Conexión del cable de 4 hilos Tira y cable de tierraConexión del cable con tres hilos CentralConexión con cable flexible de cua- tro hilos Conexión de 3 hilosPelar el cable Niveles correctos de torque para cable de aluminio o cobreConexión con cable flexible de tres hilos Antivolcadura Fijar el soporte antivolcadura al pisoRiesgo DE Volcadura DE LA Estufa Terminar la instalación Ajustar los soportes de las patasServicio Antes de llamar al servicioPlaca con datos del pro- ducto Page

HE2224(U, HE2528U, C), HE2425(U specifications

The Siemens HE2224(U, HE2528U, C) and HE2425(U) models are a testament to Siemens' commitment to innovation and efficiency in the world of electrical engineering and automation. These units offer a range of advanced features, ensuring versatility and reliability for various applications.

The HE2224(U) series is designed to deliver exceptional performance and efficiency. One of its main features is the integration of advanced communication protocols, allowing for seamless connectivity and control within an automated system. This ensures efficient data exchange and remote monitoring, making it ideal for industries seeking to optimize their processes.

Additionally, the HE2528U model is equipped with a powerful processing unit that can handle complex algorithms and real-time data analyses. This capability significantly enhances operational speed and accuracy, allowing businesses to make informed decisions quickly and efficiently. The device’s robust design also reflects Siemens' dedication to durability and longevity, ensuring that it can withstand challenging environmental conditions.

The HE2425(U) model stands out with its emphasis on energy efficiency. It incorporates cutting-edge technologies that minimize power consumption without compromising performance. This focus on sustainability aligns with global efforts to reduce energy usage and carbon footprints in industrial operations.

These models feature user-friendly interfaces that simplify programming and operation. Enhanced visualization capabilities allow users to easily monitor system performance and make adjustments as needed. This accessibility is crucial for industries that require quick adaptations to changing conditions or requirements.

Safety is another critical aspect of these units. Siemens has integrated multiple safety features, including overload protection and fault detection systems, to safeguard both equipment and personnel. This commitment to safety enhances the overall reliability of the systems, making them suitable for various industrial applications.

In summary, the Siemens HE2224(U, HE2528U, C) and HE2425(U) models represent the forefront of technological advancements in industrial automation. With their robust performance, energy efficiency, advanced communication capabilities, and focus on safety, these units provide remarkable solutions for businesses aiming to enhance productivity while prioritizing sustainability. Siemens continues to set the benchmark in electrical engineering, ensuring that their products meet the evolving needs of various industries.
Top Page Image Contents