Xantech BXAUDIO4X4 Programming Timed Delays, Programming Toggle IR Commands, Deleting a Macro

Page 23

Model BXAUDIO4X4

Page: 23

PROGRAMMING TIMED DELAYS

Timed delays can be placed in-between commands in a sequence in 1 Second intervals for up to a total of 7 Seconds.

After a successful IR Command has been learned;

1.Make sure the PROGRAM KEYPAD LED is GREEN and the STATUS LED is OFF.

2.Press the DELAY [8] Button on the front of the BXAUDIO4X4 to enter a 1 Second Delay.

3.The STATUS LED [14] will blink GREEN

4.To add more Delay time, repeat steps 1-3 for a maximum of 7 seconds of delay.

Note: If more than 7 DELAY’s are entered, the count will reset to 1 SECOND on the eighth delay.

PROGRAMMING TOGGLE IR COMMANDS

Some devices use TOGGLE IR codes where the devices remote actually has two IR codes associated to the same button. This is sometimes common with POWER commands. If it is not known if a Toggle command is present, start by learning the code as a single command. If the function is not working correctly or only works on every other press of the button, then try the following:

1.Enable PROGRAM MODE [10] (Make sure an LCKP4 Keypad is plugged into the Zone 1 Keypad port and the Keypad is ON.

2.Press the proper SOURCE BUTTON [35, 36, 37, or 38] on the LC4KP Keypad for the device to be programmed.

3.Press the PROGRAM KEYPAD [2] button on the front of the BXAUDIO4X4.

a.Confirm the PROGRAM KEYPAD LED [11] is illuminated GREEN.

4.Press the button on the LC4KP KEYPAD to be programmed

a.Confirm the STATUS LED [14] is illuminated GREEN

5.Aim the Manufactures Source Remote at the IR Learning eye on the front of the BXAUDIO4X4 [5].

6.Press and Release the corresponding button on the devices remote to record the first toggle command (make sure to use a short, quick press of the devices remote when learning commands).

Note: If the first toggle command was learned correctly the STATUS LED will turn OFF and the PROGRAM KEYPAD LED will remain GREEN.

7.Press the TOGGLE button [6] on the front of the BXAUDIO4X4.

a.The PROGRAM KEYPAD LED [11] should turn ORANGE.

b.The STATUS LED [14] should turn GREEN

8.Aim the Manufactures Source Remote at the IR Learning eye on the front of the BXAUDIO4X4 and press and release the corresponding button on the devices remote to record the second toggle command.

9.If the STATUS LED turned OFF the TOGGLE Command has been learned correctly.

DELETING A MACRO

To delete a Macro programmed under a single Keypad button:

1.Enable PROGRAM MODE (Make sure an LCKP4 Keypad is plugged into the Zone 1 Keypad port and the Keypad is ON.

2.Press the proper SOURCE BUTTON on the LC4KP Keypad for the device to be programmed.

3.Press the PROGRAM KEYPAD button on the front of the BXAUDIO4X4.

a.Confirm the PROGRAM KEYPAD LED is illuminated GREEN.

4.Press the DEL button on the front of the BXAUDIO4X4.

a.Confirm the PROGRAM KEYPAD LED is now illuminated RED.

5.Press the BUTTON on the LC4KP KEYPAD to be deleted.

a.The PROGRAM KEYPAD LED will turn OFF when the macro is deleted

© 2005 Xantech Corporation

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Installation Instructions Not Expose this Appliance to Rain or Moisture Safety Instructions Read Before Operating EquipmentTable of Contents General Information Keypad Features CONTROLLER/AMPLIFIER FeaturesZone Features/Specifications EZProgramming FeaturesFront Panel BXAUDIO4X4 CONTROLLER/AMPLIFIER Feature DescriptionsProgram Keypad LED PGM/RUN SwitchZone LED’s System Status Power-Up Mode Zone Status Operational Mode8Model BXAUDIO4X4 Model BXAUDIO4X4 BXAUDIO4X4 LC4KP Keypad Feature Descriptions Model BXAUDIO4X4 Keypad Rear Panel Features and Functions Model BXAUDIO4X4 Expanded System InstallationOperation OUT-OF-THE-BOX Source Component Connections Audio Connections LC4KP Keypad Installation InstructionsSource Label Installation Connecting the Bxaudio SystemSpeaker Connections CSM1 Threshold AdjustmentsSense Input Connections Connections AT the Zone Location AC Power ConnectionsControl Out and Status Connections Control OutOFF BXAUDIO4X4/LC4KP Keypad CAT5 Cable Lengths Extended Runs and Secondary Keypad In ZoneSpeaker Connections Zone Planning the System Enable / Disable Program ModeProgramming Button Layout Programming Keypad Buttons Single CommandsProgramming Keypad Button with a Sequence of Commands Deleting a Macro Programming Timed DelaysProgramming Toggle IR Commands Programming Source Power Management Zone System -Expanded Deleting a Power Management MacroParty Mode Linking of Zones To Un-Link Zones Combining IR Outputs Expansion ProcedureExpanded Wiring Connections Connecting the Bxaudio ControllersConfiguring the ‘Master’ Unit Zones One through Four Enabling Expansion ModeCloning the Bxaudio System Disabling Expansion ModeTo Initialize the System Initializing the System Clearing ALL MACRO’SChange Sources Buttons 1 thru Operating InstructionsParty Mode General SpecificationsIR Sensor Warranty Model BXAUDIO4X4 Xantech Corporation Xantech Corporation
Related manuals
Manual 2 pages 41.3 Kb

BXAUDIO4X4 specifications

The Xantech BXAUDIO4X4 is a powerful audio distribution system designed to meet the demands of modern multi-zone audio applications. This versatile device allows users to easily distribute high-quality audio signals from various sources to multiple zones throughout residential or commercial spaces. Its sleek design and advanced features make it a popular choice among audio professionals and enthusiasts alike.

One of the main features of the BXAUDIO4X4 is its ability to handle up to four audio sources and distribute them to four individual zones. This flexibility allows users to tailor their listening experience in each area, ensuring that everyone can enjoy their preferred audio content, whether it be music, podcasts, or live broadcasts. Each zone can be independently controlled, providing the ultimate convenience and customization.

In terms of technology, the BXAUDIO4X4 boasts built-in digital signal processing capabilities, which enhance the audio quality and ensure precise sound management. The device supports a variety of audio formats, making it compatible with numerous devices and sources, including streaming services, digital media players, and traditional audio equipment. Additionally, it features robust connection options, including XLR and RCA inputs, ensuring seamless integration into existing audio setups.

The BXAUDIO4X4 also includes user-friendly controls and an intuitive interface, making it easy for anyone to operate. The system can be controlled via a dedicated app, allowing users to adjust audio settings, select sources, and manage zones from their smartphones or tablets. This level of convenience is particularly valuable in larger spaces, where users may want to control audio without needing to access a central control point physically.

Another key characteristic of the BXAUDIO4X4 is its reliability and durability. Built to withstand the rigors of both residential and commercial environments, it features high-quality components that ensure long-lasting performance. The device is also designed for easy installation, with clear labeling and straightforward setup procedures that cater to both professional installers and DIY enthusiasts.

Overall, the Xantech BXAUDIO4X4 stands out as an exceptional audio distribution solution. With its robust features, advanced technologies, and user-centric design, it is an excellent choice for anyone looking to enhance their audio experience across multiple zones. Whether for entertaining guests, creating an immersive home theater, or managing sound in a commercial setting, the BXAUDIO4X4 delivers unparalleled performance and versatility.
Top Page Image Contents