Xantech installation instructions 8Model BXAUDIO4X4

Page 8

Page: 8Model BXAUDIO4X4

23

 

18

20

21

29

16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26 27

28

24

25

19

22

17

Figure 3 –Model BXAUDIO4X4 Controller/Amplifier – Rear Panel Features and Functions

16.Power ON/OFF Switch: Powers Unit ON and OFF when plugged into the proper AC Source.

17.AC Power Input. Standard IEC 3-Conductor AC Line Cord Receptacle for plug-in of a 3-conductor power line cord.

18.Status. Provides a control output of +12 VDC that turns on and off with the zone to drive voltage sensing relay modules and AC strips. (3.5mm Mono Mini Jack: Tip = Control Voltage, Sleeve = GND)

19.Speaker Terminals. Plug-in 4-terminal screw type connectors permit speaker wire sizes up to 12 gauge. Speaker Output is 25W per Channel @8-Ohms (4-Ohm capable).

20.Keypad Terminals. Each Zone has one RJ-45 jack for LC4KP Keypad Interface. Each connector interfaces the following: Power (Enough for 1 Primary & 1 Secondary Keypad per Zone), RS-422 Data I/O, and IR Input.

21.Control Out. Provides a Control Output that goes high (+12 volts DC) when any zone is first turned on and goes low (0 volts) when the last zone is turned off. (3.5mm Mono Mini Jack: Tip = Control Voltage, Sleeve = GND)

22.Level Reset. Pressing this button twice within 1 second restores all of the Factory Default Settings for all zones. The Factory Defaults are as follows:

a.Mute Off

b.Z-Adjust Treble and Bass Flat

c.Z-Adjust Balance Centered

d.Z-Adjust Max-V Cleared

e.Trim Levels Cleared

f.IR Code Group set to A8

NOTE: The Control Amp will always return to last set values (plus any unaltered factory defaults) after main power shut down or after any power interruptions.

23.Source Audio Inputs. Gold-plated RCA Jacks for line level audio input from source components.

24.IR Out (1-4). 3.5mm Mono Mini Phone Jacks. These mini jacks are for the connection of Xantech IR emitters (283M Emitters Included) and are ‘Auto-Routed’ for controlling the corresponding numbered Audio Source Component.

© 2005 Xantech Corporation

Image 8
Contents Installation Instructions Safety Instructions Read Before Operating Equipment Not Expose this Appliance to Rain or MoistureTable of Contents General Information CONTROLLER/AMPLIFIER Features Zone Features/SpecificationsEZProgramming Features Keypad FeaturesBXAUDIO4X4 CONTROLLER/AMPLIFIER Feature Descriptions Front PanelPGM/RUN Switch Zone LED’s System Status Power-Up ModeZone Status Operational Mode Program Keypad LED8Model BXAUDIO4X4 Model BXAUDIO4X4 BXAUDIO4X4 LC4KP Keypad Feature Descriptions Model BXAUDIO4X4 Keypad Rear Panel Features and Functions Model BXAUDIO4X4 Expanded System InstallationOperation OUT-OF-THE-BOX LC4KP Keypad Installation Instructions Source Label InstallationConnecting the Bxaudio System Source Component Connections Audio ConnectionsSpeaker Connections CSM1 Threshold AdjustmentsSense Input Connections AC Power Connections Control Out and Status ConnectionsControl Out Connections AT the Zone LocationOFF Extended Runs and Secondary Keypad In Zone BXAUDIO4X4/LC4KP Keypad CAT5 Cable LengthsSpeaker Connections Zone Enable / Disable Program Mode Planning the SystemProgramming Button Layout Programming Keypad Buttons Single CommandsProgramming Keypad Button with a Sequence of Commands Deleting a Macro Programming Timed DelaysProgramming Toggle IR Commands Programming Source Power Management Zone System -Expanded Deleting a Power Management MacroParty Mode Linking of Zones To Un-Link Zones Expansion Procedure Expanded Wiring ConnectionsConnecting the Bxaudio Controllers Combining IR OutputsEnabling Expansion Mode Configuring the ‘Master’ Unit Zones One through FourDisabling Expansion Mode Cloning the Bxaudio SystemInitializing the System Clearing ALL MACRO’S To Initialize the SystemOperating Instructions Change Sources Buttons 1 thruParty Mode General SpecificationsIR Sensor Warranty Model BXAUDIO4X4 Xantech Corporation Xantech Corporation
Related manuals
Manual 2 pages 41.3 Kb

BXAUDIO4X4 specifications

The Xantech BXAUDIO4X4 is a powerful audio distribution system designed to meet the demands of modern multi-zone audio applications. This versatile device allows users to easily distribute high-quality audio signals from various sources to multiple zones throughout residential or commercial spaces. Its sleek design and advanced features make it a popular choice among audio professionals and enthusiasts alike.

One of the main features of the BXAUDIO4X4 is its ability to handle up to four audio sources and distribute them to four individual zones. This flexibility allows users to tailor their listening experience in each area, ensuring that everyone can enjoy their preferred audio content, whether it be music, podcasts, or live broadcasts. Each zone can be independently controlled, providing the ultimate convenience and customization.

In terms of technology, the BXAUDIO4X4 boasts built-in digital signal processing capabilities, which enhance the audio quality and ensure precise sound management. The device supports a variety of audio formats, making it compatible with numerous devices and sources, including streaming services, digital media players, and traditional audio equipment. Additionally, it features robust connection options, including XLR and RCA inputs, ensuring seamless integration into existing audio setups.

The BXAUDIO4X4 also includes user-friendly controls and an intuitive interface, making it easy for anyone to operate. The system can be controlled via a dedicated app, allowing users to adjust audio settings, select sources, and manage zones from their smartphones or tablets. This level of convenience is particularly valuable in larger spaces, where users may want to control audio without needing to access a central control point physically.

Another key characteristic of the BXAUDIO4X4 is its reliability and durability. Built to withstand the rigors of both residential and commercial environments, it features high-quality components that ensure long-lasting performance. The device is also designed for easy installation, with clear labeling and straightforward setup procedures that cater to both professional installers and DIY enthusiasts.

Overall, the Xantech BXAUDIO4X4 stands out as an exceptional audio distribution solution. With its robust features, advanced technologies, and user-centric design, it is an excellent choice for anyone looking to enhance their audio experience across multiple zones. Whether for entertaining guests, creating an immersive home theater, or managing sound in a commercial setting, the BXAUDIO4X4 delivers unparalleled performance and versatility.