Frymaster M3000 manual MIB Replacement, AIF Replacement

Page 40

LOV™ Generation II Technical Reference

MIB Replacement

The MIB controller is located inside the left cabinet (see image below). In normal operation, a cover hides the MIB controls. The LED display is visible.

1.Disconnect the fryer from the electrical power supply.

2.Remove the three torx screws from the MIB cover, exposing the MIB board (see image at right).

3.Remove the screw in the center top will allow the board to hinge down and expose the connections on the back of the board.

4.Disconnect the MIB board by carefully removing the plugs on the rear of the board (see image at right).

5.Replace with a new MIB board and reverse steps to reassemble.

6.Once replaced, reconnect the power.

7.Cycle all power to the unit to readdress

the fryer using the steps on the previous page.

2 screws

Cover

1 screw

MIB controller cover (three screws hold it in place).

AIF Replacement

The AIF boards are located inside a protective housing underneath each frypot.

1.Disconnect the fryer from the electrical power supply.

2.Locate the AIF board to be replaced under a frypot.

3.Mark and unplug the harnesses.

4.Locate the screw on the front of the AIF assembly holding it in place.

5.Remove the screw and the front of the assembly drops down and the back tab slides out of the bracket attached to the frypot (see below).

6.Reverse steps to reassemble, ensuring that the new AIF assembly slides into the slot in the rear of the bracket.

7.Cycle all power to the unit to readdress the fryer using the steps on the previous page.

Remove this screw that secures the AIF board to the fryer.

After removing the screw, the AIF assembly drops down.

The bottom tab slides out of the bracket attached to the frypot.

39

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Line Ave, Shreveport, LA Service Hotline Frymaster and Dean Technical ServiceFEB Edition Introducing the Low Oil Volume Fryer Auto Top Off RTDTroubleshooting the Top Off System No power to ATO boardATO Board Yellow JIB low lightProblem Probable Causes Corrective Action Frypots won’t top offOne vat tops off but other Vats fail to top offAuto Filtration MIB and AIF Drain ResetReturn Error Codes Manual Draining, Filling, Filtering with MIBTroubleshooting the Manual Interface Board MIB Problem Probable Cause Corrective ActionMIB board alternat Oil Return Sensor Troubleshooting Gas LOV Fryers Troubleshooting the AIF System AIFProblem Probable Cause Fix Typical sensor-related failures M3000 Computer Overview Filter, Temperature, and Info Buttons NavigationCook Cycle and Selection Buttons Temp ButtonBasic Operation Cooking With Multi-Product Display Cooking With Dedicated Display Changing from Breakfast Setup to Lunch Changing from Lunch Setup to Breakfast M3000 Menu Items Location in IO manual Loading and Updating Software Procedures Card Until the Display Prompts to do SO in StepM3000 Troubleshooting Call Service MisconfiguredException Error Filter PADError RM Sdcrd Temp ProbeMaint Filter Remove DiscardVAT FULL? YES no Reset Recovery Fault Call Service M3000 Useful CodesService Required Errors Error Message ExplanationCode Error Message Explanation Error ATO BoardTech Mode Fryer Setup ModeLOV Generation II Technical Reference LOV Generation II Technical Reference Filter Error Flow Chart Normal Operation ResumesFor Syst EM ER ROR FIX ED? YES Syst EM ER ROR FIX ED? YES noTroubleshooting RTI-equipped SystemsBulk Oil LOV Wiring LOVGenerationHOT or Used oil to Oil Disposal and Fill with RTI-equipped SystemsJIB New Oil Tank Waste Oil Tank RTI LOV Test Quick Reference Dispose to WASTE, Refill VAT from BulkFill VAT from Bulk Board and Computer Replacement Readdress All BoardsMIB Replacement AIF ReplacementM3000 Computer Replacement ATO Pump ReplacementWiring Diagrams LOV Electric FryerLOV Gas Fryer Middle Data Network Flow ChartRight ATO RTD ATO Automatic Top Off Pin Positions and HarnessesAIF J5 MIB Manual Interface Board Pin Positions and Harnesses AIF J4MIB Manual Interface Board Display Diagnostics Network Resetting MiscellaneousDisplay LED Explanation DrainDV AIF RTD ATO J10M3000 Board, Harnesses, and Pin Positions Only Used on NON-AIF UnitsEnglish February 23

M3000 specifications

The Frymaster M3000 is a state-of-the-art frying solution that has gained popularity in commercial kitchens due to its impressive capabilities and advanced technologies. This fryer is designed to provide consistent, high-quality results while maintaining efficiency, making it an ideal choice for restaurants, fast food outlets, and foodservice operations.

One of the significant features of the Frymaster M3000 is its oil management system. This advanced technology helps to extend the life of the cooking oil, reducing overall costs and improving food quality. The system monitors the oil's condition and alerts users when it is time to filter or change the oil, ensuring that the frying process remains uncompromised and that food is cooked to perfection.

The M3000 is equipped with a precise temperature control feature that allows users to set and maintain accurate cooking temperatures. This is critical in achieving optimal frying results, as various food items require different temperature settings for the best flavor and texture. The fryer also boasts rapid recovery times, meaning that it can quickly return to the desired temperature even after adding food, which is essential during busy peak times.

Additionally, the Frymaster M3000 incorporates a unique fry pot design that promotes even heat distribution throughout the cooking oil. This feature helps in reducing hot and cold spots, allowing for a more consistent frying experience. The design also facilitates easy cleaning, as the fry pot can be easily removed and maintained, thus improving overall kitchen hygiene.

Another notable characteristic of the M3000 is its user-friendly digital control interface. This intuitive system allows operators to program cooking times and temperatures easily, streamlining the frying process. With built-in diagnostic features, the fryer can notify users of potential issues, aiding in preventive maintenance and reducing downtime.

The Frymaster M3000 is also designed with safety in mind. Features such as auto shut-off, temperature limiters, and secure oil containment systems reduce the risk of accidents in busy kitchen environments. This attention to safety reassures operators that they are using a reliable piece of machinery.

In summary, the Frymaster M3000 is an exceptional commercial fryer that combines advanced technology, user-friendly controls, and a focus on safety and efficiency. Its oil management system, precision temperature control, rapid recovery, and ease of maintenance make it a preferred choice for foodservice professionals seeking reliable and high-quality frying solutions. With the M3000, consistent performance and culinary excellence are always within reach.
Top Page Image Contents