Frymaster 8196339 operation manual Electrical Grounding Requirements, Caster/Leg Installation

Page 11

2.The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).

2.1.3 Electrical Grounding Requirements

All electrically operated appliances must be grounded in accordance with all applicable national and local codes, and, where applicable, CE codes. In the absence of local codes, the appliance must be grounded in accordance with National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2, as applicable. All units (cord connected or permanently connected) should be connected to a grounded power supply system. A wiring diagram is located on the inside of the fryer door. Refer to the rating plate on the inside of the fryer door for proper voltages.

DANGER

This appliance is equipped with a special (grounding) plug for your protection against electrical shock, and must be plugged directly into a properly grounded re- ceptacle. Do not cut, remove, or otherwise bypass the grounding prong on this plug!

DANGER

This appliance requires electrical power for operation. Place the gas control valve in the OFF position in case of a prolonged power outage. Do not attempt to operate this appliance during a power outage.

2.1.4 Australian Requirements

To be installed in accordance with AS 5601 / AG 601, local authority, gas, electricity, and any other relevant statutory regulations.

2.2Caster/Leg Installation

Depending upon the specific configuration ordered, your fryer may have been shipped without installed casters or legs. DO NOT INSTALL THIS APPLIANCE WITHOUT CASTERS OR

LEGS. If the appliance requires the installation of casters or legs, install them in accordance with the instructions included in your accessory package.

On an appliance with casters; the installation shall be made with a connector that complies with the Standard for Moveable Gas Appliances, ANSI Z21.69 • CSA 6.16, and a quick disconnect device that complies with the Standard for Quick-Disconnect Devices for Use With Gas Fuel, ANSI Z21.41

• CSA 6.9.

2.3Pre-Connection Preparations

DANGER

DO NOT connect this appliance to the gas supply before completing each step in this section.

2-3

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Protector Series GAS Fryers Hour Service HotlineCanada Iii Applicability and Validity Safety InformationEuropean Community CE Specific Information Computer Information for the CM7 ComputersDefinitions Installation, Operating, and Service PersonnelEquipment Description What to do if your equipment arrives damaged Shipping Damage Claim ProcedureParts Ordering and Service Information Retain and Store this Manual in a Safe Place for Future USE Do not block the area around the base or under the fryers General Installation RequirementsNational Code Requirements Electrical Grounding Requirements Caster/Leg InstallationNon-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE Standard Non-CE Standard Burner Manifold Gas Pressures CE GAS Conversion Instructions Converting to another Gas TypePositioning the Fryer Finding Your WAY around the Protector Series GAS Fryer Protector Series GAS Fryer Operating InstructionsController Operation and Programming Lighting the Fryer Press the computer ON/OFF switch to the OFF positionShutting the Fryer Down Boiling Out the FrypotRoutine Oil Changes Install the Oil ReservoirOil Attendant Automatic Top-Off Prepare the System for UseBulk Oil Systems CM7 General Information Protector Series GAS Fryers CM7 Computer InstructionsBasic Operation Cooking with Multi-Product Display Cooking with Dedicated Display FR FriesChanging from Breakfast Setup to Lunch Changing from Lunch Setup to Breakfast Navigation Buttons CM7 Button Description and FunctionsStoring Product Menu Items in Product Buttons Temperature Conversion from F to CCM7 Menu Summary Tree Adding New Product Menu Items12hr Setup Mode ProgrammingSetup 7378Page Page 1650 10 CM7 Common TasksPage Sensitivity Storing Menu Items in Product Buttons 1658 Boil-Out ModeSetpoint Temperature Page E06 Ignition Failure Call Technician Manager Mode4321 To E-LOGOff, 1 the softest and 9 the loudest Sensitivity Settings for Various Products Protector Series GAS Fryers Filtration Instructions Preparing the Built-In Filtration System for Use Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Operation of the Filter Filter Pump Reset Switch Separate the outer screens and grid Reassembly CleaningDraining and Disposing of Waste Oil Clean Fryer Cabinet Inside and Out Fryer Preventative Maintenance Checks and ServiceDaily Checks and Service Inspect Fryer and Accessories for DamageCheck Computer Magic 7 Set Point Accuracy Monthly Checks and ServiceBlower Wiring connection assembly mounting nuts Left Viewing Port is Behind Motor Right Page Built-In Filtration System FryerPage Introduction Protector Series GAS Fryers Operator TroubleshootingProblem Probable Causes Corrective Action Troubleshooting Fryers Computer and Heating ProblemsProbable Causes Corrective ActionFiltration Problems Problem Probable Causes Corrective ActionBasket Lift Problems Problem Probable CausesAuto Top-Off Problems Service Hotline

8196339 specifications

The Frymaster 8196339 is a high-performance commercial fryer designed for busy kitchens that demand efficiency and reliability. Renowned for its innovative features and advanced technologies, this fryer is an essential tool for restaurants, food trucks, and other food establishments looking to serve crispy, delicious fried foods.

One of the standout features of the Frymaster 8196339 is its exceptional frying capacity. With a generous oil capacity, this fryer can handle a significant volume of food at once, making it ideal for high-demand cooking environments. This large capacity allows operators to prepare larger batches of fries, chicken, and other fried specialties without sacrificing quality or increasing cooking time.

The Frymaster 8196339 utilizes advanced temperature control technology, ensuring precise temperature management for consistent frying results. The unit is equipped with a digital thermostat that allows operators to set and monitor frying temperatures accurately. This feature not only enhances the quality of the finished product but also helps in energy efficiency, as it minimizes oil temperature fluctuations that can lead to overcooked or undercooked food.

Another notable characteristic of the Frymaster 8196339 is its built-in filtration system. This technology helps maintain oil quality, extending the life of the cooking oil, and providing a cleaner frying process. The filtration system operates automatically, allowing for easy maintenance and ensuring that the fryer produces consistent, high-quality results with every batch.

Safety is also a priority in the design of the Frymaster 8196339. The fryer is equipped with safety controls and features such as automatic shutoff and high-temperature protection. These elements work together to help prevent overheating and reduce the risk of accidents in the kitchen environment.

In terms of construction, the Frymaster 8196339 is built with durable materials that ensure longevity and resistance to wear and tear. The stainless-steel body is not only aesthetically pleasing but also easy to clean, making maintenance a hassle-free task.

Overall, the Frymaster 8196339 combines capacity, efficiency, advanced technologies, and safety features to provide an outstanding frying solution. Operators can rely on this commercial fryer to deliver exceptional culinary results while enhancing productivity in a fast-paced kitchen setting. Whether it’s frying potatoes, chicken, or other favorites, the Frymaster 8196339 ensures that food is cooked to perfection every time.
Top Page Image Contents