Frymaster 8196339 operation manual Gas Connection Pipe Sizes

Page 13

2.4Connection to Gas Line

DANGER

Before connecting new pipe to this appliance, the pipe must be blown out thor- oughly to remove all foreign material. Foreign material in the burner and gas con- trols will cause improper and dangerous operation.

DANGER

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of ½ PSI (3.45 kPa, 13.84 inches W.C.) to avoid damage to the fryer’s gas tubes and gas valve(s).

DANGER

The appliance must be isolated from the gas supply piping system by closing its in- dividual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ PSI (3.45 kPa, 13.84 inches W.C.)

DANGER

“Dry-firing” your unit will cause damage to the frypot and can cause a fire. Always ensure that cooking oil or water is in the frypot before firing the unit.

DANGER

All connections must be sealed with a joint compound suitable for the gas being used and all connections must be tested with a solution of soapy water before light- ing any pilots.

Never use matches, candles, or any other ignition source to check for leaks. If gas odors are detected, shut off the gas supply to the appliance at the main shut-off valve and immediately contact the local gas company or an authorized service agency for service.

The size of the gas line used for installation is very important. If the line is too small, the gas pressure at the burner manifold will be low. This may cause slow recovery and delayed ignition. The incoming gas supply line should be a minimum of 1½” (38 mm) in diameter. Refer to the chart below for the minimum sizes of connection piping.

Gas Connection Pipe Sizes

(Minimum incoming pipe size should be 1 1/2" (41 mm))

 

 

 

 

4 or more

Gas

Single Unit

2 - 3 Units

 

units*

Natural

3/4" (22 mm)

1" (28 mm)

1

1/4" (36 mm)

Propane

1/2" (15 mm)

3/4" (22 mm)

 

1" (28 mm)

Manufactured

1" (28 mm)

1 1/4" (36 mm)

1

1/2" (41 mm)

 

 

 

 

 

2-5

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Protector Series GAS Fryers Hour Service HotlineCanada Iii Applicability and Validity Safety InformationEuropean Community CE Specific Information Computer Information for the CM7 ComputersEquipment Description Installation, Operating, and Service PersonnelDefinitions Parts Ordering and Service Information Shipping Damage Claim ProcedureWhat to do if your equipment arrives damaged Retain and Store this Manual in a Safe Place for Future USE Do not block the area around the base or under the fryers General Installation RequirementsNational Code Requirements Electrical Grounding Requirements Caster/Leg InstallationNon-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE Standard Non-CE Standard Burner Manifold Gas Pressures CE GAS Conversion Instructions Converting to another Gas TypePositioning the Fryer Finding Your WAY around the Protector Series GAS Fryer Protector Series GAS Fryer Operating InstructionsController Operation and Programming Lighting the Fryer Press the computer ON/OFF switch to the OFF positionShutting the Fryer Down Boiling Out the FrypotOil Attendant Automatic Top-Off Install the Oil ReservoirPrepare the System for Use Routine Oil ChangesBulk Oil Systems CM7 General Information Protector Series GAS Fryers CM7 Computer InstructionsBasic Operation Cooking with Multi-Product Display Cooking with Dedicated Display FR FriesChanging from Breakfast Setup to Lunch Changing from Lunch Setup to Breakfast Navigation Buttons CM7 Button Description and FunctionsCM7 Menu Summary Tree Temperature Conversion from F to CAdding New Product Menu Items Storing Product Menu Items in Product ButtonsSetup Setup Mode Programming7378 12hrPage Page 1650 10 CM7 Common TasksPage Sensitivity Storing Menu Items in Product Buttons 1658 Boil-Out ModeSetpoint Temperature Page 4321 Manager ModeTo E-LOG E06 Ignition Failure Call TechnicianOff, 1 the softest and 9 the loudest Sensitivity Settings for Various Products Protector Series GAS Fryers Filtration Instructions Preparing the Built-In Filtration System for Use Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Operation of the Filter Filter Pump Reset Switch Separate the outer screens and grid Reassembly CleaningDraining and Disposing of Waste Oil Daily Checks and Service Fryer Preventative Maintenance Checks and ServiceInspect Fryer and Accessories for Damage Clean Fryer Cabinet Inside and OutCheck Computer Magic 7 Set Point Accuracy Monthly Checks and ServiceBlower Wiring connection assembly mounting nuts Left Viewing Port is Behind Motor Right Page Built-In Filtration System FryerPage Introduction Protector Series GAS Fryers Operator TroubleshootingProblem Probable Causes Corrective Action Troubleshooting Fryers Computer and Heating ProblemsProbable Causes Corrective ActionFiltration Problems Problem Probable Causes Corrective ActionAuto Top-Off Problems Problem Probable CausesBasket Lift Problems Service Hotline

8196339 specifications

The Frymaster 8196339 is a high-performance commercial fryer designed for busy kitchens that demand efficiency and reliability. Renowned for its innovative features and advanced technologies, this fryer is an essential tool for restaurants, food trucks, and other food establishments looking to serve crispy, delicious fried foods.

One of the standout features of the Frymaster 8196339 is its exceptional frying capacity. With a generous oil capacity, this fryer can handle a significant volume of food at once, making it ideal for high-demand cooking environments. This large capacity allows operators to prepare larger batches of fries, chicken, and other fried specialties without sacrificing quality or increasing cooking time.

The Frymaster 8196339 utilizes advanced temperature control technology, ensuring precise temperature management for consistent frying results. The unit is equipped with a digital thermostat that allows operators to set and monitor frying temperatures accurately. This feature not only enhances the quality of the finished product but also helps in energy efficiency, as it minimizes oil temperature fluctuations that can lead to overcooked or undercooked food.

Another notable characteristic of the Frymaster 8196339 is its built-in filtration system. This technology helps maintain oil quality, extending the life of the cooking oil, and providing a cleaner frying process. The filtration system operates automatically, allowing for easy maintenance and ensuring that the fryer produces consistent, high-quality results with every batch.

Safety is also a priority in the design of the Frymaster 8196339. The fryer is equipped with safety controls and features such as automatic shutoff and high-temperature protection. These elements work together to help prevent overheating and reduce the risk of accidents in the kitchen environment.

In terms of construction, the Frymaster 8196339 is built with durable materials that ensure longevity and resistance to wear and tear. The stainless-steel body is not only aesthetically pleasing but also easy to clean, making maintenance a hassle-free task.

Overall, the Frymaster 8196339 combines capacity, efficiency, advanced technologies, and safety features to provide an outstanding frying solution. Operators can rely on this commercial fryer to deliver exceptional culinary results while enhancing productivity in a fast-paced kitchen setting. Whether it’s frying potatoes, chicken, or other favorites, the Frymaster 8196339 ensures that food is cooked to perfection every time.
Top Page Image Contents