Jenn-Air W10208727A Mark line, Mark pilot holes, Attach handle, Attach body panel

Page 15

2 Dishwashers with control panel on top custom panel dimensions

3 screws per side

outer panel

Gently set outer panel aside. Lay the customer-supplied custom panel face down on a covered, non-scratching surface.

3 Mark line

9 29/32”

(25.2 cm)

Back

Top edge

Measure 9 29/32" (25.2 cm) from top edge and mark a line on the back of customer-supplied custom panel. Position the outer panel on the back of the customer-supplied custom panel as shown, so that the top holes in the outer panel are on the line, and both panels are centered side to side.

4 Mark pilot holes

Mark pilot

holes

5 Attach handle

6”

(15.2 mm)

Hex Head

Screw

Attach outer panel to back of customer-supplied custom panel with the four #10-16 x 3/8" hex head screws supplied in the literature package. Attach the handle. The handle should be centered on the front of the customer-supplied custom panel in the area shown.

IMPORTANT: Screw heads must be flush with back of customer-supplied custom panel.

6 Attach body panel

 

Align top

Reinstall

edges

 

3 screws

 

each side

Customer-supplied

 

panel

Attach the panel assembly to the door by reinstalling the three screws on each side; do not tighten completely. This reinstallation of the three screws will hold the panel assembly in place on the door frame.

7 Install custom panel

Mark all four hole locations; remove outer panel. Drill 3/32" pilot holes 1/2" (13 mm) deep in customer-supplied custom panel. Place the outer panel on the back of the customer- supplied custom panel; align holes.

Customer-supplied

panel

Align top edges

Drill through

these holes

Align the top edge of the customer-supplied custom panel with the top of the console.

Drill two 3/32" pilot holes 1/2" (13 mm) deep, into the customer-supplied custom panel, through the holes in the top corners on the inner panel, as shown.

15

Image 15
Contents W10208727A You Need to Table of ContentsTools and Parts Location Requirements 60 /8 Product and Cabinet Opening DimensionsUse of air gap Drain RequirementsWater Supply Requirements Electrical RequirementsPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Install Drain Hose Waste disposer with air gap Install Moisture Barrier on some modelsInstall moisture barrier on some models No waste disposer no air gapPrepare Dishwasher Power Cord-Connect remaining wires Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Power Supply Cord- Connect ground wireDetermine Cabinet Opening Built-up Floors-Add shims as needed Install the Door Handle on some modelsInstall Custom Panel Install door handleAttach handle Install custom panelMark line Mark pilot holesBreak end of bracket Choose Attachment OptionCountertop attachment Remove brackets from the topCheck water and drain hose position Reinstall bracket Move dishwasher close to cabinet openingMove Dishwasher into Cabinet Opening Stand dishwasher uprightMove dishwasher into cabinet opening Check for plumb and adjust legs if neededCloses too quickly Decrease spring tension Door falls open Increase spring tensionConnect to Water Supply Connect to Drain Make Direct Wire Electrical ConnectionSlide clamp onto connector Direct Wire--Route cable into terminal boxDirect Wire-Reinstall terminal box cover Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Secure cable in strain reliefSecure Dishwasher in Cabinet Opening Complete Installation If Dishwasher Does Not Operate Power supply cord-Plug into a grounded 3 prong outletReconnect power Check OperationPage Il faut Table des matièresOutillage et pièces Exigences demplacement Enlev Utilisation du dispositif de brise-siphon Exigences dévacuationSpécifications de l’alimentation en eau Spécifications électriquesQuel type de connexion lutilisateur emploie-t-il? Interromprelalimentation électriqueFermeture de lalimentation en eau Lutilisateur possède-t-il déjà des moyens de raccordement?Raccordement direct Préparation du trou Préparation et acheminement de la canalisation d’eauCordon dalimentation électrique Préparation du trou Perçage du trouInstallation du tuyau d’évacuation Pas de broyeur à déchets sans brise-siphon Pas de broyeur à déchets avec brise-siphonBroyeur à déchets avec brise-siphon Application de ruban adhésif Téflon ou composé détanchéité Préparation du lave-vaissellePlacer le lave-vaisselle sur le dos Dépose des panneauxRaccordement du cordon dalimentation Installation dun serre-câbleTableau de réglage de la hauteur du lave-vaisselle Configuration du câblageÉvaluation de l’ouverture dencastrement du placard Mesure de louverture dencastrement du placardPlanchers surélevés Ajouter des cales si nécessaire Installation de la poignée de porte sur certains modèlesInstallation du panneau personnalisé Installation de la poignée de porteArrière Marquage de laxeMarquage des avant-trous Fixation de la poignéeFixation au plan de travail Installation du panneau personnaliséChoix de l’option de fixation Fixation du panneau principalInsertion des boutons en plastique Réinstallation de la brideDéplacement du lave-vaisselle à proximité de louverture Sectionnement de lextrémité de la brideInsertion du lave-vaisselle dans louverture du placard Ouverture et fermeture de la porteEnfiler lécrou et la virole sur la canalisation Méthode recommandée Méthode facultativeRaccordement à l’alimentation en eau Vérification de laplomb et réglage des pieds si nécessairePosition définitive de la bride de tuyau Raccordement au circuit dévacuationEnfilement de la bride sur le raccord Recherche de fuitesRaccordement électrique direct Raccordement direct Raccordement du fil de mise à la terreRaccordement direct Raccordement des fils restants Raccordement direct Fixation du câble dans le serre-câble Vérification de la fixation latérale Fixation du lave-vaisselleVérification de la distance de dégagement pour la porte Vérification de lespacement à lintérieurSerrage des vis Achever linstallationRéinstallation des panneaux daccès Inspection de la rive de panneau inférieureRétablir l’alimentation électrique Contrôle du fonctionnementSi le lave-vaisselle ne fonctionne pas correctement Reconnexion de lalimentation électriqueConseils supplémentaires

W10208727A specifications

The Jenn-Air W10208727A is a high-performance appliance that exemplifies the brand's commitment to quality and innovation. Designed to enhance the functionality and convenience of modern kitchens, this model integrates several advanced features and technologies that cater to various culinary needs.

One of the standout characteristics of the Jenn-Air W10208727A is its powerful and efficient motor, which ensures optimal performance during operation. This motor is coupled with a robust design that guarantees durability and longevity, allowing it to withstand the rigors of daily kitchen use. The appliance comes equipped with a range of settings, enabling users to customize their cooking experience according to their preferences.

The W10208727A boasts an intuitive control panel that simplifies operation. The user-friendly interface allows for precise adjustments to cooking temperatures and times, making it easy to achieve the perfect results every time. Additionally, its sleek design and finish make it an attractive addition to any kitchen, complementing modern aesthetics while providing practicality.

Another notable feature of this model is its innovative temperature management technology, which ensures even heating and cooking throughout the appliance. This technology minimizes hotspots and ensures that food is cooked uniformly, enhancing overall cooking performance. As a result, users can enjoy perfectly cooked meals with minimal effort.

Moreover, the Jenn-Air W10208727A incorporates advanced safety features, such as auto shut-off capabilities, which help prevent overheating and ensure safe operation. This attention to safety reflects the brand’s commitment to providing not just functionality but also peace of mind for users.

In terms of maintenance, the appliance is designed for easy cleaning, with removable parts that can be easily detached and washed. This practical feature is essential for busy households that prioritize efficiency without compromising on cleanliness and hygiene.

Overall, the Jenn-Air W10208727A combines innovative technology, user-friendly design, and robust performance to meet the needs of today’s culinary enthusiasts. Whether you are an experienced chef or a home cook, this appliance proves to be an invaluable tool in the kitchen, enhancing your cooking experience and allowing you to explore new culinary creations with ease. With its range of features and reliable performance, it stands as a testament to Jenn-Air's legacy of excellence in kitchen appliances.