Jenn-Air W10208727A Drain Requirements, Water Supply Requirements, Electrical Requirements

Page 6

Drain Requirements

•A new drain hose is supplied with your dishwasher.

If drain hose is not long enough, use a new drain hose with a maximum length of 12’ (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1” (2.5 cm) drain connector of the dishwasher.

•Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20”

(50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap.

Use of air gap

Air gap

•Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20” (50.8 cm) above subfloor or floor.

•Use 1/2” minimum I.D. drain line fittings.

•If required, the air gap should be installed in accordance with the air gap installation instructions. When you are connecting the air gap a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

Water Supply Requirements

•A hot water line with 20-120 psi (138-862 kPa) water pressure can be verified by a licensed plumber.

•120°F (49°C) water at dishwasher.

•3/8” O.D. copper tubing with compression fitting or flexible braided water supply line (Part Number 4396897RP)

NOTE: 1/2” minimum plastic tubing is not recommended.

•A 90° elbow with 3/8” N.P.T. external pipe threads on one end.

•Do not solder within 6” (15.2 cm) from water inlet valve.

6

Electrical Requirements

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association

One Batterymarch Park Quincy, MA 02269

You must have:

•120-volt, 60 Hz, AC-only, 15 or 20 amp, fused electrical supply.

•copper wire only.

We recommend:

•a time-delay fuse or circuit breaker.

•a separate circuit.

If connecting dishwasher with a power supply cord:

•Use UL listed power supply cord kit (Part Number 4317824) marked for use with dishwasher.

•Power supply cord must plug into

a grounded 3 prong outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances.

If connecting dishwasher with direct wiring:

•Use flexible, armored or nonmetallic

sheathed, copper wire with grounding wire

that meets the wiring requirements for your home and local codes and ordinances.

•Use a UL Listed/CSA Certified strain relief.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents W10208727A Table of Contents You Need toTools and Parts Location Requirements Product and Cabinet Opening Dimensions 60 /8Electrical Requirements Drain RequirementsWater Supply Requirements Use of air gapPrepare Cabinet Opening-Existing Utilities Prepare Cabinet Opening-New UtilitiesPrepare and Route Water Line Install Drain Hose No waste disposer no air gap Install Moisture Barrier on some modelsInstall moisture barrier on some models Waste disposer with air gapPrepare Dishwasher Power Supply Cord- Connect ground wire Make Power Supply Cord ConnectionPower Cord-Route cord into terminal box Power Cord-Connect remaining wiresDetermine Cabinet Opening Install door handle Install the Door Handle on some modelsInstall Custom Panel Built-up Floors-Add shims as neededMark pilot holes Install custom panelMark line Attach handleRemove brackets from the top Choose Attachment OptionCountertop attachment Break end of bracketStand dishwasher upright Reinstall bracket Move dishwasher close to cabinet openingMove Dishwasher into Cabinet Opening Check water and drain hose positionDoor falls open Increase spring tension Check for plumb and adjust legs if neededCloses too quickly Decrease spring tension Move dishwasher into cabinet openingConnect to Water Supply Direct Wire--Route cable into terminal box Make Direct Wire Electrical ConnectionSlide clamp onto connector Connect to DrainDirect Wire-Secure cable in strain relief Direct Wire-Connect ground wireDirect Wire-Connect remaining wires Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Complete Installation Check Operation Power supply cord-Plug into a grounded 3 prong outletReconnect power If Dishwasher Does Not OperatePage Table des matières Il fautOutillage et pièces Exigences demplacement Enlev Spécifications électriques Exigences dévacuationSpécifications de l’alimentation en eau Utilisation du dispositif de brise-siphonLutilisateur possède-t-il déjà des moyens de raccordement? Interromprelalimentation électriqueFermeture de lalimentation en eau Quel type de connexion lutilisateur emploie-t-il?Perçage du trou Préparation et acheminement de la canalisation d’eauCordon dalimentation électrique Préparation du trou Raccordement direct Préparation du trouInstallation du tuyau d’évacuation Pas de broyeur à déchets sans brise-siphon Pas de broyeur à déchets avec brise-siphonBroyeur à déchets avec brise-siphon Dépose des panneaux Préparation du lave-vaissellePlacer le lave-vaisselle sur le dos Application de ruban adhésif Téflon ou composé détanchéitéInstallation dun serre-câble Raccordement du cordon dalimentationMesure de louverture dencastrement du placard Configuration du câblageÉvaluation de l’ouverture dencastrement du placard Tableau de réglage de la hauteur du lave-vaisselleInstallation de la poignée de porte Installation de la poignée de porte sur certains modèlesInstallation du panneau personnalisé Planchers surélevés Ajouter des cales si nécessaireFixation de la poignée Marquage de laxeMarquage des avant-trous ArrièreFixation du panneau principal Installation du panneau personnaliséChoix de l’option de fixation Fixation au plan de travailSectionnement de lextrémité de la bride Réinstallation de la brideDéplacement du lave-vaisselle à proximité de louverture Insertion des boutons en plastiqueOuverture et fermeture de la porte Insertion du lave-vaisselle dans louverture du placardVérification de laplomb et réglage des pieds si nécessaire Méthode recommandée Méthode facultativeRaccordement à l’alimentation en eau Enfiler lécrou et la virole sur la canalisationRecherche de fuites Raccordement au circuit dévacuationEnfilement de la bride sur le raccord Position définitive de la bride de tuyauRaccordement électrique direct Raccordement direct Raccordement du fil de mise à la terreRaccordement direct Raccordement des fils restants Raccordement direct Fixation du câble dans le serre-câble Vérification de lespacement à lintérieur Fixation du lave-vaisselleVérification de la distance de dégagement pour la porte Vérification de la fixation latéraleInspection de la rive de panneau inférieure Achever linstallationRéinstallation des panneaux daccès Serrage des visReconnexion de lalimentation électrique Contrôle du fonctionnementSi le lave-vaisselle ne fonctionne pas correctement Rétablir l’alimentation électriqueConseils supplémentaires

W10208727A specifications

The Jenn-Air W10208727A is a high-performance appliance that exemplifies the brand's commitment to quality and innovation. Designed to enhance the functionality and convenience of modern kitchens, this model integrates several advanced features and technologies that cater to various culinary needs.

One of the standout characteristics of the Jenn-Air W10208727A is its powerful and efficient motor, which ensures optimal performance during operation. This motor is coupled with a robust design that guarantees durability and longevity, allowing it to withstand the rigors of daily kitchen use. The appliance comes equipped with a range of settings, enabling users to customize their cooking experience according to their preferences.

The W10208727A boasts an intuitive control panel that simplifies operation. The user-friendly interface allows for precise adjustments to cooking temperatures and times, making it easy to achieve the perfect results every time. Additionally, its sleek design and finish make it an attractive addition to any kitchen, complementing modern aesthetics while providing practicality.

Another notable feature of this model is its innovative temperature management technology, which ensures even heating and cooking throughout the appliance. This technology minimizes hotspots and ensures that food is cooked uniformly, enhancing overall cooking performance. As a result, users can enjoy perfectly cooked meals with minimal effort.

Moreover, the Jenn-Air W10208727A incorporates advanced safety features, such as auto shut-off capabilities, which help prevent overheating and ensure safe operation. This attention to safety reflects the brand’s commitment to providing not just functionality but also peace of mind for users.

In terms of maintenance, the appliance is designed for easy cleaning, with removable parts that can be easily detached and washed. This practical feature is essential for busy households that prioritize efficiency without compromising on cleanliness and hygiene.

Overall, the Jenn-Air W10208727A combines innovative technology, user-friendly design, and robust performance to meet the needs of today’s culinary enthusiasts. Whether you are an experienced chef or a home cook, this appliance proves to be an invaluable tool in the kitchen, enhancing your cooking experience and allowing you to explore new culinary creations with ease. With its range of features and reliable performance, it stands as a testament to Jenn-Air's legacy of excellence in kitchen appliances.
Top Page Image Contents