Jenn-Air W10208727A Check Operation, If Dishwasher Does Not Operate, Additional Tips

Page 24

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1 Power supply cord—Plug into a grounded 3 prong outlet

Plug into a grounded 3 prong outlet. Check that power supply cord does not touch dishwasher motor or lower part of dishwasher tub.

Reconnect Power

1 Reconnect power

Reconnect electrical power at the fuse box or circuit breaker box.

24

Check Operation

❏Read the Dishwasher User Instructions that came with your dishwasher.

❏Check that all parts have been installed and no steps were skipped. Check that you have all tools used.

❏Start dishwasher and allow it to complete the shortest wash cycle. After the first 2 minutes unlatch door, wait 5 seconds, then open door. Check that there is water in the bottom of the dishwasher tub. Check that dishwasher is working properly.

If the dishwasher is not working properly, disconnect power or unplug dishwasher and see “If Dishwasher Does Not Operate” section.

If Dishwasher Does Not Operate

First try the solutions suggested here to possibly avoid the cost of a service call.

•Has the circuit breaker tripped or the house fuse blown?

•Is the door closed tightly and latched?

•Has the cycle been set correctly to start the dishwasher?

•Is the water turned on?

If none of these possible solutions work, call

1-800-688-1100, or in Canada, call 1-800-807-6777.

Additional Tips

Expect longer wash times. Your new dishwasher will average 2-3 hours per load, but use nearly 40% less energy than older models. Designed with a low wattage, low energy consumption motor, your dishwasher washes longer to ensure exceptional cleaning. Certain models are equipped with an optical water sensor so the first cycle will run longer to calibrate to optical sensor. Selecting certain options could increase cycle time past 3.5 hours.

Rinse aid is necessary for good drying results:

This dishwasher is designed to be used with rinse aid for good drying performance and controlling hard water deposit buildup. Energy efficient dishwashers use less water and energy, so they depend on the water sheeting action of rinse aid for good drying performance.

Start/Resume light may flash:

When pressing Start/Resume, you must make sure the door is closed within 3 seconds. If you do not close the door within 3 seconds, the Start/Resume light will flash until you press it again. (You must also do this when adding a dish during the middle of a cycle.)

Page 23 Page 25
Image 24
Page 23 Page 25
Contents W10208727A Table of Contents You Need toTools and Parts Location Requirements Product and Cabinet Opening Dimensions 60 /8Drain Requirements Water Supply RequirementsElectrical Requirements Use of air gapPrepare Cabinet Opening-Existing Utilities Prepare Cabinet Opening-New UtilitiesPrepare and Route Water Line Install Drain Hose Install Moisture Barrier on some models Install moisture barrier on some modelsNo waste disposer no air gap Waste disposer with air gapPrepare Dishwasher Make Power Supply Cord Connection Power Cord-Route cord into terminal boxPower Supply Cord- Connect ground wire Power Cord-Connect remaining wiresDetermine Cabinet Opening Install the Door Handle on some models Install Custom PanelInstall door handle Built-up Floors-Add shims as neededInstall custom panel Mark lineMark pilot holes Attach handleChoose Attachment Option Countertop attachmentRemove brackets from the top Break end of bracketReinstall bracket Move dishwasher close to cabinet opening Move Dishwasher into Cabinet OpeningStand dishwasher upright Check water and drain hose positionCheck for plumb and adjust legs if needed Closes too quickly Decrease spring tensionDoor falls open Increase spring tension Move dishwasher into cabinet openingConnect to Water Supply Make Direct Wire Electrical Connection Slide clamp onto connectorDirect Wire--Route cable into terminal box Connect to DrainDirect Wire-Connect ground wire Direct Wire-Connect remaining wiresDirect Wire-Secure cable in strain relief Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Complete Installation Power supply cord-Plug into a grounded 3 prong outlet Reconnect powerCheck Operation If Dishwasher Does Not OperatePage Table des matières Il fautOutillage et pièces Exigences demplacement Enlev Exigences dévacuation Spécifications de l’alimentation en eauSpécifications électriques Utilisation du dispositif de brise-siphonInterromprelalimentation électrique Fermeture de lalimentation en eauLutilisateur possède-t-il déjà des moyens de raccordement? Quel type de connexion lutilisateur emploie-t-il?Préparation et acheminement de la canalisation d’eau Cordon dalimentation électrique Préparation du trouPerçage du trou Raccordement direct Préparation du trouInstallation du tuyau d’évacuation Pas de broyeur à déchets sans brise-siphon Pas de broyeur à déchets avec brise-siphonBroyeur à déchets avec brise-siphon Préparation du lave-vaisselle Placer le lave-vaisselle sur le dosDépose des panneaux Application de ruban adhésif Téflon ou composé détanchéitéInstallation dun serre-câble Raccordement du cordon dalimentationConfiguration du câblage Évaluation de l’ouverture dencastrement du placardMesure de louverture dencastrement du placard Tableau de réglage de la hauteur du lave-vaisselleInstallation de la poignée de porte sur certains modèles Installation du panneau personnaliséInstallation de la poignée de porte Planchers surélevés Ajouter des cales si nécessaireMarquage de laxe Marquage des avant-trousFixation de la poignée ArrièreInstallation du panneau personnalisé Choix de l’option de fixationFixation du panneau principal Fixation au plan de travailRéinstallation de la bride Déplacement du lave-vaisselle à proximité de louvertureSectionnement de lextrémité de la bride Insertion des boutons en plastiqueOuverture et fermeture de la porte Insertion du lave-vaisselle dans louverture du placardMéthode recommandée Méthode facultative Raccordement à l’alimentation en eauVérification de laplomb et réglage des pieds si nécessaire Enfiler lécrou et la virole sur la canalisationRaccordement au circuit dévacuation Enfilement de la bride sur le raccordRecherche de fuites Position définitive de la bride de tuyauRaccordement électrique direct Raccordement direct Raccordement du fil de mise à la terreRaccordement direct Raccordement des fils restants Raccordement direct Fixation du câble dans le serre-câble Fixation du lave-vaisselle Vérification de la distance de dégagement pour la porteVérification de lespacement à lintérieur Vérification de la fixation latéraleAchever linstallation Réinstallation des panneaux daccèsInspection de la rive de panneau inférieure Serrage des visContrôle du fonctionnement Si le lave-vaisselle ne fonctionne pas correctementReconnexion de lalimentation électrique Rétablir l’alimentation électriqueConseils supplémentaires

W10208727A specifications

The Jenn-Air W10208727A is a high-performance appliance that exemplifies the brand's commitment to quality and innovation. Designed to enhance the functionality and convenience of modern kitchens, this model integrates several advanced features and technologies that cater to various culinary needs.

One of the standout characteristics of the Jenn-Air W10208727A is its powerful and efficient motor, which ensures optimal performance during operation. This motor is coupled with a robust design that guarantees durability and longevity, allowing it to withstand the rigors of daily kitchen use. The appliance comes equipped with a range of settings, enabling users to customize their cooking experience according to their preferences.

The W10208727A boasts an intuitive control panel that simplifies operation. The user-friendly interface allows for precise adjustments to cooking temperatures and times, making it easy to achieve the perfect results every time. Additionally, its sleek design and finish make it an attractive addition to any kitchen, complementing modern aesthetics while providing practicality.

Another notable feature of this model is its innovative temperature management technology, which ensures even heating and cooking throughout the appliance. This technology minimizes hotspots and ensures that food is cooked uniformly, enhancing overall cooking performance. As a result, users can enjoy perfectly cooked meals with minimal effort.

Moreover, the Jenn-Air W10208727A incorporates advanced safety features, such as auto shut-off capabilities, which help prevent overheating and ensure safe operation. This attention to safety reflects the brand’s commitment to providing not just functionality but also peace of mind for users.

In terms of maintenance, the appliance is designed for easy cleaning, with removable parts that can be easily detached and washed. This practical feature is essential for busy households that prioritize efficiency without compromising on cleanliness and hygiene.

Overall, the Jenn-Air W10208727A combines innovative technology, user-friendly design, and robust performance to meet the needs of today’s culinary enthusiasts. Whether you are an experienced chef or a home cook, this appliance proves to be an invaluable tool in the kitchen, enhancing your cooking experience and allowing you to explore new culinary creations with ease. With its range of features and reliable performance, it stands as a testament to Jenn-Air's legacy of excellence in kitchen appliances.
Top Page Image Contents