Jenn-Air W10208727A installation instructions Install Drain Hose

Page 9

3 Route water supply line

Slowly route water supply line through hole in cabinet. (If using copper tubing, it will bend and kink easily, so be gentle.) It should be far enough into the cabinet opening to connect it to the dishwasher inlet on the front left side of the dishwasher.

4 Flush water supply line

Slowly turn water shutoff valve to “ON” position. Flush water into a shallow pan until clear to get rid of particles that could clog the inlet valve. Turn shutoff valve to “OFF” position.

Install Drain Hose

IMPORTANT: Always use a new drain hose. Check local codes to determine if an air gap is required.

1 Drill hole

1 1/2”

(3.8 cm)

If needed, drill a 1 1/2” (3.8 cm) diameter hole in cabinet wall or side of the opening closest to the sink.

2 Route drain hose

Drain hose

Route drain hose as shown through hole in cabinet to the front center of opening where drain connection will be made. Tape drain hose to the floor in area shown. This will prohibit it from moving when dishwasher is moved into cabinet opening.

3 Connect drain hose

Connect drain hose to waste tee or waste disposer using one of the following options:

Option A, Waste disposer – no air gap

Option B, No waste disposer – no air gap

Option C, Waste disposer – with air gap

Option D, No waste disposer – with air gap

IMPORTANT: The drain hose connection of the disposer or a waste tee must be made before the drain trap and at least 20” (50.8 cm) above the floor where the dishwasher will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away from the floor.

Option A, Waste disposer – no air gap

Waste disposer – no air gap

Disposer inlet

 

Large silver

 

drain hose clamp

 

 

Drain hose

 

 

Drain trap

1

1. Using a hammer and screwdriver,

knock plug into disposer.

 

2

2. Use needle-nose pliers to remove

 

 

plug.

3 3. Attach drain hose to disposer inlet with large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position.

9

Image 9
Contents W10208727A You Need to Table of ContentsTools and Parts Location Requirements 60 /8 Product and Cabinet Opening DimensionsWater Supply Requirements Drain RequirementsElectrical Requirements Use of air gapPrepare Cabinet Opening-New Utilities Prepare Cabinet Opening-Existing UtilitiesPrepare and Route Water Line Install Drain Hose Install moisture barrier on some models Install Moisture Barrier on some modelsNo waste disposer no air gap Waste disposer with air gapPrepare Dishwasher Power Cord-Route cord into terminal box Make Power Supply Cord ConnectionPower Supply Cord- Connect ground wire Power Cord-Connect remaining wiresDetermine Cabinet Opening Install Custom Panel Install the Door Handle on some modelsInstall door handle Built-up Floors-Add shims as neededMark line Install custom panelMark pilot holes Attach handleCountertop attachment Choose Attachment OptionRemove brackets from the top Break end of bracketMove Dishwasher into Cabinet Opening Reinstall bracket Move dishwasher close to cabinet openingStand dishwasher upright Check water and drain hose positionCloses too quickly Decrease spring tension Check for plumb and adjust legs if neededDoor falls open Increase spring tension Move dishwasher into cabinet openingConnect to Water Supply Slide clamp onto connector Make Direct Wire Electrical ConnectionDirect Wire--Route cable into terminal box Connect to DrainDirect Wire-Connect remaining wires Direct Wire-Connect ground wireDirect Wire-Secure cable in strain relief Direct Wire-Reinstall terminal box coverSecure Dishwasher in Cabinet Opening Complete Installation Reconnect power Power supply cord-Plug into a grounded 3 prong outletCheck Operation If Dishwasher Does Not OperatePage Il faut Table des matièresOutillage et pièces Exigences demplacement Enlev Spécifications de l’alimentation en eau Exigences dévacuationSpécifications électriques Utilisation du dispositif de brise-siphonFermeture de lalimentation en eau Interromprelalimentation électriqueLutilisateur possède-t-il déjà des moyens de raccordement? Quel type de connexion lutilisateur emploie-t-il?Cordon dalimentation électrique Préparation du trou Préparation et acheminement de la canalisation d’eauPerçage du trou Raccordement direct Préparation du trouInstallation du tuyau d’évacuation Pas de broyeur à déchets sans brise-siphon Pas de broyeur à déchets avec brise-siphonBroyeur à déchets avec brise-siphon Placer le lave-vaisselle sur le dos Préparation du lave-vaisselleDépose des panneaux Application de ruban adhésif Téflon ou composé détanchéitéRaccordement du cordon dalimentation Installation dun serre-câbleÉvaluation de l’ouverture dencastrement du placard Configuration du câblageMesure de louverture dencastrement du placard Tableau de réglage de la hauteur du lave-vaisselleInstallation du panneau personnalisé Installation de la poignée de porte sur certains modèlesInstallation de la poignée de porte Planchers surélevés Ajouter des cales si nécessaireMarquage des avant-trous Marquage de laxeFixation de la poignée ArrièreChoix de l’option de fixation Installation du panneau personnaliséFixation du panneau principal Fixation au plan de travailDéplacement du lave-vaisselle à proximité de louverture Réinstallation de la brideSectionnement de lextrémité de la bride Insertion des boutons en plastiqueInsertion du lave-vaisselle dans louverture du placard Ouverture et fermeture de la porteRaccordement à l’alimentation en eau Méthode recommandée Méthode facultativeVérification de laplomb et réglage des pieds si nécessaire Enfiler lécrou et la virole sur la canalisationEnfilement de la bride sur le raccord Raccordement au circuit dévacuationRecherche de fuites Position définitive de la bride de tuyauRaccordement électrique direct Raccordement direct Raccordement du fil de mise à la terreRaccordement direct Raccordement des fils restants Raccordement direct Fixation du câble dans le serre-câble Vérification de la distance de dégagement pour la porte Fixation du lave-vaisselleVérification de lespacement à lintérieur Vérification de la fixation latéraleRéinstallation des panneaux daccès Achever linstallationInspection de la rive de panneau inférieure Serrage des visSi le lave-vaisselle ne fonctionne pas correctement Contrôle du fonctionnementReconnexion de lalimentation électrique Rétablir l’alimentation électriqueConseils supplémentaires

W10208727A specifications

The Jenn-Air W10208727A is a high-performance appliance that exemplifies the brand's commitment to quality and innovation. Designed to enhance the functionality and convenience of modern kitchens, this model integrates several advanced features and technologies that cater to various culinary needs.

One of the standout characteristics of the Jenn-Air W10208727A is its powerful and efficient motor, which ensures optimal performance during operation. This motor is coupled with a robust design that guarantees durability and longevity, allowing it to withstand the rigors of daily kitchen use. The appliance comes equipped with a range of settings, enabling users to customize their cooking experience according to their preferences.

The W10208727A boasts an intuitive control panel that simplifies operation. The user-friendly interface allows for precise adjustments to cooking temperatures and times, making it easy to achieve the perfect results every time. Additionally, its sleek design and finish make it an attractive addition to any kitchen, complementing modern aesthetics while providing practicality.

Another notable feature of this model is its innovative temperature management technology, which ensures even heating and cooking throughout the appliance. This technology minimizes hotspots and ensures that food is cooked uniformly, enhancing overall cooking performance. As a result, users can enjoy perfectly cooked meals with minimal effort.

Moreover, the Jenn-Air W10208727A incorporates advanced safety features, such as auto shut-off capabilities, which help prevent overheating and ensure safe operation. This attention to safety reflects the brand’s commitment to providing not just functionality but also peace of mind for users.

In terms of maintenance, the appliance is designed for easy cleaning, with removable parts that can be easily detached and washed. This practical feature is essential for busy households that prioritize efficiency without compromising on cleanliness and hygiene.

Overall, the Jenn-Air W10208727A combines innovative technology, user-friendly design, and robust performance to meet the needs of today’s culinary enthusiasts. Whether you are an experienced chef or a home cook, this appliance proves to be an invaluable tool in the kitchen, enhancing your cooking experience and allowing you to explore new culinary creations with ease. With its range of features and reliable performance, it stands as a testament to Jenn-Air's legacy of excellence in kitchen appliances.