Extron electronic TP T 15HD AV, TP T BNC DA4, TP T 468 Installing the TP T, Through-desk mounting

Page 13

Installation and Operation, cont’d

Through-desk mounting

Mount the transmitter through a desk or table, using the optional through-desk mounting kit (part #70-077-02).

Figure 2-5Through-desk mounting the transmitter

1.

Mark the opening through which the unit will be

 

mounted — approximately 1.2" by 6.9" (3.0 cm by 17.5 cm).

2.

Cut out the material from the installation area with a

 

jigsaw.

3.

Drill pilot holes 1/4" (6.4 mm) deep and 3/32" (2 mm) in

 

diameter in the desk or table at the locations of the

 

mounting bracket screws. The holes should be drilled

 

from the underside or inside (concealed side) of the

 

furniture where the transmitter will be located.

4.

Using the four provided wood screws, attach the brackets

 

to the mounting surface.

5.

Slide the unit up and down or back and forth in the

 

mounting brackets until the front panel of the unit is at the

 

desired height. Tighten the screws that secure the bracket

 

in place.

 

If the screws are inaccessible to a screwdriver,

 

a.

Mark the location of the brackets relative to the

 

 

screws.

 

b.

Remove the transmitter from inside the furniture.

c. Tighten the screws.

d.

Replace the unit inside the surface (repeat step 4).

Installing the TP T 468

TP T 468 Installation Overview

To install a TP T 468 transmitter, follow these steps:

1Disconnect power from all of the equipment, including the video source(s) (such as computers or DVD players), the transmitter, the receiver, and the output display(s).

2For non-Euro Channel (EC) versions, prepare the site: cut a hole in the wall/furniture, install the electrical box or mud ring, and prepare the cables. Instructions are included in this manual and/or with the wall box. See “Preparing the site and installing the mud ring or wall box,” later in this chapter.

For the EC versions, see “Euro Channel transmitter installation,” later in this chapter.

3Connect the input cables. See “Input cabling,” later in this chapter.

4Connect the cable(s) between the transmitter(s) and the TP receiver(s). See “Transmitted signal cabling,” later in this chapter , and refer to the TP Receivers Family User’s Manual, part #68-547-01.

5Configure the TP receiver(s). Refer to the TP Receivers Family User’s Manual, part #68-547-01.

6Connect power cords to the TP receiver(s), the TP transmitter(s) (if applicable), and turn on the video source(s) and the output display(s).

The TP T 468 includes a 15 VDC external power supply. The transmitter also receives power from the associated Extron TP receiver via the TP cable. Extron recommends using the local power supply; however, the TP T 468 may not require a local power supply for cable lengths of 300’ (91.4 m) or less. If problems are encountered, use the local power supply.

7Adjust the picture controls on the front panel of the transmitter and receiver. See Front Panel Control and Indicators, later in this chapter, and refer to the TP Receivers Family User’s Manual, part #68-547-01.

8Disconnect power from all the devices.

2-10 Extron TP Transmitters • Installation and Operation

Extron TP Transmitters • Installation and Operation 2-11

Image 13
Contents TP Transmitters Family Extron’s Warranty PrecautionsFCC Class a Notice Table of Contents Appendix a Specifications , Accessories, Table of Contents, cont’dTP Transmitters Introductionduction,cont’d About the TP Transmitters FeaturesTP T 15HD a transmitter TP T 15HD AV transmitter Introduction, cont’dTP T 468 transmitter TP T BNC DA4 transmitter/distribution amplifierTwo Extron TP Transmitters Installation and Operation Instaltal lationandandOperation,cont’d InstallationOverview Video jumpersVideo DIP switch Installation and Operation, cont’dAudio jumpers Mounting the TP T 15HD A, TP T 15HD AV, or Rack mounting procedureTabletop use UL rack mounting guidelinesUnder-desk mounting Attach the rack shelf to the rack using the supplied boltsTP T 468 Installation Overview Installing the TP TThrough-desk mounting Preparing the site and installing the mud ring or wall box UL guidelines for wall box installationEuro Channel models Grounding outer braided and foil shields Mounting the transmitter to the mud ring or wall box Mounting the AAP devicesGrounding the transmitter Installing the Euro Channel transmitterComputer video and PC audio Input cabling16 Installation features, TP T Computer Input connector Connect aComposite video and stereo audio Transmitted signal cablingRgbhv video Termination of TP cable Cable testingEqualizing pair skew Unique TP T 468 front panel features Front Panel Control and IndicatorsPower connector If the image does not appear TroubleshootingIf the image is not displayed correctly If the receiver’s Manual/Auto LED flashesAAppendix Audio VideoAudio input GeneralTP T 15HD AV TP T BNC DA4 Specifications, Accessories, and Part Numbers, cont’dIncluded Parts AccessoriesCables and Adapters TP TFront connector type Rear connector typeOptional Adapter Plates Adapter plate descriptionMulti Type Connector Architectural Adapter Plates TP T 468 Template TP T 468 4-gang Cut-out TemplateSpecifications, Accessories, and Part Numbers, cont’d
Related manuals
Manual 1 pages 13.51 Kb Manual 1 pages 31.54 Kb

TP T 468, TP T 15HD A, TP T 15HD AV, TP T BNC DA4 specifications

The Extron Electronics TP T BNC DA4 is a cutting-edge distribution amplifier designed for professional audio and video applications. It elegantly combines a compact form factor with robust functionality, making it an essential tool for any AV system requiring signal distribution. This unit is built to handle high-resolution video signals with ease, ensuring that content reaches multiple outputs without degradation or loss in quality.

One of the standout features of the TP T BNC DA4 is its ability to support a wide range of signals including SDI, HD-SDI, and 3G-SDI. This versatility allows it to adapt seamlessly to various broadcast and production environments, ensuring compatibility with existing equipment. The unit boasts four identical BNC outputs, which can deliver pristine video signals to multiple displays or recording devices.

The TP T BNC DA4 employs advanced technologies to maintain signal integrity over longer distances. The unit features advanced signal processing, ensuring that even when distributing signals across significant lengths, there is minimal degradation. This is crucial in professional settings where maintaining signal fidelity is paramount.

Built with reliability in mind, the Extron TP T BNC DA4 is constructed from durable materials and designed for easy integration into various rack environments. Furthermore, its compact design ensures that it can be installed without taking up excessive space, which is an essential consideration in many professional settings.

Another important characteristic of the TP T BNC DA4 is its user-friendly interface. With straightforward controls and clear status indicators, operators can easily monitor signal quality and configuration. The device also offers options for adjusting sync settings and maintaining optimum performance.

Finally, the Extron TP T BNC DA4 is backed by the company’s commitment to quality and support, providing users with peace of mind and reliability. Extron's reputation for excellence in the AV industry makes the TP T BNC DA4 a trusted choice among professionals who require high-quality signal distribution solutions.

In summary, the Extron Electronics TP T BNC DA4 is a powerful and reliable distribution amplifier that meets the demands of modern AV systems with its advanced features, robust build quality, and commitment to signal integrity. It is an indispensable component for any professional setup that seeks to deliver high-quality audio and video signals to multiple outputs efficiently.