Extron electronic manual USP 507 Reset Mode Summary, Mode Activation Result Purpose/Notes

Page 20

Installation, cont’d

USP 507 Reset Mode Summary

 

 

Mode Activation

Result

Purpose/Notes

 

 

 

 

1 Hold down the recessed Reset button

The USP 507 reverts to the factory default firmware.

This mode reverts to

 

 

while applying power to the unit.

Event scripting does not start if the device is powered

the factory default

FactoryUse Firmware

N After a mode 1 reset is performed,

on in this mode. All user files and settings (drivers,

firmware version if

adjustments, IP settings, etc.) are maintained.

incompatibility issues

update the USP 507 firmware to the

 

using an earlier

 

 

latest version. The reset tofactory intsled

N If you do not want to update firmware, or you

arise with user-loaded

 

 

firmware is temporary. When power is

performed a mode 1 reset by mistake, cycle power to the

firmware.

 

 

cycled, the unit uses the last installed

device to return to the firmware version that was

N User-defined

 

 

firmware. Do not operate the firmware

running prior to the mode 1 reset. Use the 0Q SIS

Web pages may not

 

 

version that results from this mode reset.

command to confirm that the factory default firmware is

work correctly if

 

 

If you want to use the factory default

no longer running (look for asterisks following the version

firmware version.

 

 

firmware, you must upload that version

number.)

 

 

again. See page 6-10 for details on

 

 

 

 

 

 

 

 

uploading firmware.

 

 

 

 

 

 

 

Run/Stop

Events

3 Hold down the Reset button for about 3

This Mode turns events on or off.

This mode is useful

sec. until the Power LED blinks once,

N Nothing happens if the momentary press

for troubleshooting.

 

 

 

 

then release and press Reset

 

 

 

does not occur within 1 second. During resetting LED

 

 

 

momentarily (<1 sec.) within 1 second.

 

 

 

flashes twice if events are starting, and three times if

 

 

 

 

 

 

 

 

events are stopping.

 

 

 

4 Hold down the Reset button for about

This Mode:

This mode enables

allReset SettingsIP

6 sec. until the Power LED blinks twice

• Enables ARP capability.

you to set IP address

(once at 3 sec., again at 6 sec.). Then

• Sets the IP address back to factory default

information using

 

 

 

 

release and press Reset momentarily

(192.168.254.254).

ARP and the MAC

 

 

(for <1 sec.) within 1 second.

• Sets the subnet back to factory default.

address.

 

 

N Nothing happens if the momentary

• Sets the default gateway address to the factory default.

 

 

 

• Sets port mapping back to factory default.

 

 

 

press does not occur within 1 second.

 

 

 

• Turns DHCP off.

 

 

 

 

 

 

 

 

• Turns events off.

 

 

 

 

 

 

toReset DefaultsFactory

5 Hold down the Reset button for about

This Mode performs a complete reset to factory

This mode is useful if

 

 

 

 

9 sec. until the Power LED blinks three

defaults (except the firmware).

you want to start over

 

 

times (once at 3 sec., again at 6 sec.,

• Does everything mode 4 does.

with configuration

 

 

again at 9 sec.). Then release and press

• Resets all IP options.

and uploading, and

 

 

Reset momentarily (for <1 sec.) within

• Removes scheduling settings.

also to replace events.

 

 

1 second.

• Removes/clears all files from the USP 507.

 

 

 

N Nothing happens if the momentary

• Resets all user video settings.

 

 

 

 

 

 

 

press does not occur within 1 second.

 

 

 

 

 

 

 

2-8 USP 507 • Installation

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Universal Signal Processor USPPrecautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschFCC Class a Notice Table of Contents Table of Contents, cont’d Installing and Starting the Signal Processing USP 507 Table of Contents IiiIv USP 507 Table of Contents One Introduction About this ManualAbout the USP USP 507 IntroductionDefinitions Features Introduction, cont’dUSP 507 Introduction Two Installationstallation, cont’d UL/Safety RequirementsImportant safety instructions USP 507 InstallationTabletop placement Mounting the USPUL guidelines for rack mounted devices Rack mountingPower and video input connections Installation, cont’dRear Panel Features and Connections Output, user interface, and control connections Installation and cabling Default display cycle Powering UpResetting the Unit with the Reset Button USP 507 Reset Mode Summary Mode Activation Result Purpose/NotesThree Front Panel Operation Front Panel OverviewSpecial function buttons These four buttons are Picture control buttons These six buttons areButton Backlighting Switching InputsSpecial Function Button Operation Overview of menus FrontPanelOperation,co t’dUSP 507 Menu System USP 507 Front Panel Operation NextUsing the menus User presetsSave a user preset Recall a user presetInput configuration Settings for each signal formatOutput configuration Press Next or Menu to return to the Output ConfigurationTo recall an image Image capture/recallTo capture an image Advanced configuration To remove an image from the displayAdjust knob to turn the Auto Memory on or off. See -6 for Exit menu View comm settingsEdit comm settings Enabling or disabling Executive mode 1 from the front panel Setting the Front Panel Locks Executive ModesScan converter configuration Setting Up the USP 507 to Work with a Matrix Switcher USP 507 connected to a matrix switcherConnection must be via IP not RS-232 USP 507 Input #3 select the matrixRS-232 cable only Extron USPFour Ethernet LAN\⤀ Port SIS Programmer’s GuideRS-232/RS-422 Link Connection timeouts Using verbose modeHost-to-Processor Instructions Processor-Initiated MessagesSIS Programmer’s Guide, cont’d Processor Error ResponsesUsing the Command/Response Table for SIS Commands Symbol definitions = SecamSIS Programmer’s Guide, cont’d Command Response Table for SIS Commands Command Ascii command Response Additional descriptionInput Switching and Configuration $HSRTXphas TpixApix XalinX1% Colr X1%TINTX1%CONT X1%BRITX1& Hsiz X1&VSIZX1* Zoom X1HPANX2#OPOL X2$OSYNX7%VTPO X7VSTDESX1&HSIZ ESX1&VSIZESX7&HDET ESX7&VDETAdvanced Configurations X2TESTX3&VDLY Front panel lockout executive mode\⤀Picture in Picture PIPX5TIME Image capture/recall to USP 507 flash memory ResetsInformation request Using the Command/Response Table for IP SIS Commands Command/Response Table for IP SIS Commands WX12#CV ECVEFF EAEWX12%CD ~CJECJ Ethernet data portProgrammer’s Guide, cont’dEDF ELFFive Installing the program USP 507 SoftwareStarting the program USP 507 USP 507 SoftwareUsing the Program OrientationUSP 507 Software, cont’d Control program menusFile menu Options menuTools menu Download Now USP 507 USP 507 Software Help menu Sppcp Help file’s main windowControl tab Control tab screenConfiguration tab I/O Configuration tab screenAdvanced Settings tab Advanced Features Within this sectionScan Converter tab Scan Converter tab screenImage Capture tab Status barSix Accessing the Web Pages Html OperationStart the Web browser program USP 507 Html OperationSystem Status System StatusConfiguration Pages System SettingsIP Settings fields Html Operation, cont’dDhcp radio buttons IP Address fieldGateway IP Address field Subnet Mask fieldDate/Time Settings fields Date/Time Settings fieldsScaler Settings Scaler settingsRGB delay, test pattern, and Edid selections Passwords PasswordsFirmware Upgrade Download product namefirmware version.exe buttonFile Management Choose file window with a firmware file selectedUploading files Adding a directoryOther file management activities Delete all files Click Delete AllControl Pages User ControlMemory/Input Presets PIP Setup/PIP PresetsImages Image is not yet displayedReference Information AAppendix aUSP 507 Reference Information SpecificationsReference Information Sync Reference Information, cont’d MtbfPart Numbers and Accessories AccessoriesIncluded parts Optional I/O boardsAppendixBB Default address Ethernet ConnectionEthernet Link Ping to determine Extron IP addressUSP 507 Ethernet Connection Connect as a Telnet clientPing to determine Web IP address Connecting to the USP 507 Open command\⤀ Ethernet Connection, cont’dTelnet tips Escape character and Esc keySubnetting a Primer GatewaysLocal and remote devices IP addresses and octetsSubnet masks and octets Determining whether devices are on the same subnetUnmasked octets are compared indicated by ? in figure B-6 Masked octets are not compared indicated by X in figure B-6Asia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle East China

USP 507 specifications

Extron Electronics has long been a leader in the field of professional AV system design, and one of their standout products is the USP 507. The USP 507 is an advanced universal speaker processor that is engineered to elevate audio performance across a variety of applications. Designed for both commercial and residential environments, the USP 507 combines cutting-edge technology with user-friendly features to deliver superior sound quality and precise audio control.

One of the main features of the USP 507 is its comprehensive signal processing capabilities. The device supports a range of audio formats and delivers 48 kHz or 96 kHz sample rates, ensuring high fidelity in audio reproduction. It also includes a configurable 5-band equalizer per channel, allowing users to fine-tune audio output to accommodate different room acoustics and speaker types.

The USP 507 is equipped with Extron’s patented SpeedMatch technology to enhance speaker performance and optimize audio clarity. This innovative technology automatically analyzes the audio signals and adjusts various parameters to compensate for environmental conditions, ensuring consistent sound quality across all outputs.

In terms of connectivity, the USP 507 offers a wide array of input and output options. It includes both balanced and unbalanced audio inputs to facilitate seamless integration with other audio equipment. Furthermore, the device provides multiple output zones, enabling simultaneous audio distribution to different areas within a facility.

The USP 507 features intuitive software for simplified setup and operation. The Extron Toolbelt application allows users to configure, manage, and monitor the speaker processor through an easy-to-navigate interface. This software enhances user experience by providing real-time diagnostics and seamless integration with other Extron devices.

Durability and reliability are also hallmarks of the USP 507. Built with high-quality materials, it is designed to withstand the demands of professional use while ensuring long-lasting performance. Additionally, the device comes equipped with advanced thermal management features to prevent overheating during extended operations.

In summary, the Extron USP 507 is a versatile universal speaker processor that combines advanced signal processing technologies, a user-friendly interface, and robust construction. Its ability to deliver superior audio performance makes it an ideal choice for various applications, ranging from corporate environments to high-end residential setups. With its comprehensive features and reliable performance, the USP 507 stands out as an essential tool for audio professionals seeking to enhance their sound experience.
Top Page Image Contents