Extron electronic USP 507 manual Advanced configuration, To remove an image from the display

Page 30

Front Panel Operation, cont’d

Step 1

MENU

Press NEXT twice

LCD screen displays

Recall to back:

<N/A>

MENU

Press

three NEXT times

ADJUST

LCD screen displays

Recall to front:

<N/A>

LCD screen displays

Rotate either

Recall:

Adjust knob.

IMG05.BMP

Step 2

 

MENU

Press

NEXT

LCD screen displays

Recalling Image

Please wait

then

IMG05.BMP

Recalled

To remove an image from the display:

1. Press Next twice. The LCD displays “Recall to back: <N/A>”. If the image is displayed at the front, press Next again so the LCD displays “Recall to Front: <N/A>”.

2.With the appropriate “Recall to back: <N/A>” or “Recall to front: <N/A>” displayed, press Next. The current image is removed from the display, but not from the USP 507 memory. To recall the image follow the steps described in the “To recall an image” section, on this page.

Advanced configuration

Within this menu auto imaging and auto memory can be turned on or off, Input EDID can be set, RGB delay value adjusted, the switch effect chosen, a test pattern selected to aid setting up the display, and the MTP pre-peaking turned on or off. In addition the internal temperature can be read, and the unit can reset to factory default settings.

NAt any submenu, if the input is incorrect, press the desired input button, and then proceed with the setting adjustment.

1. Press Next to enter the first sublevel, Auto Image. The current active input and setting status is displayed. See the table below for a full description of the interaction between the auto image and auto memory settings.

Auto Image Input #2 On

 

 

Auto Memory and Auto-Image Features

 

 

 

Auto Memory

Auto Image

Information

 

 

 

ON

ON

“New” signals /rates that have not been previously detected by the USP 507 are initially set-up

 

 

using default parameters, then auto image is automatically applied and values stored. The next

 

 

time the same signal is detected, the values stored in the auto memory location are applied.

 

 

 

ON

OFF

“New” signals /rates that have not been previously detected by the USP 507 are set-up using

(Default)

(Default)

default parameters. If manual input and/or picture settings are made to the input, an auto

 

 

memory location is created and recalled each successive time the input is detected.

OFF

ON

Each change in input sync triggers an automatic auto image. When auto memory is disabled,

 

 

each different signal is treated as a new signal and default picture controls and automatic auto

 

 

image is applied. Any manual changes made to the image and picture controls are lost each time

 

 

a new rate is detected.

 

 

 

OFF

OFF

Each change in input sync causes default values to be applied to the rate. Any manual changes

 

 

made to the image and picture controls are lost each time a new rate is applied.

Figure 3-6 — Auto Memory and Auto-Image features table

3-10 USP 507 • Front Panel Operation

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Universal Signal Processor USPConsignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen DeutschFCC Class a Notice Table of Contents Table of Contents, cont’d Installing and Starting the Signal Processing USP 507 Table of Contents IiiIv USP 507 Table of Contents One About the USP IntroductionAbout this Manual USP 507 IntroductionDefinitions Features Introduction, cont’dUSP 507 Introduction Two Important safety instructions Installationstallation, cont’dUL/Safety Requirements USP 507 InstallationUL guidelines for rack mounted devices Tabletop placementMounting the USP Rack mountingInstallation, cont’d Rear Panel Features and ConnectionsPower and video input connections Output, user interface, and control connections Installation and cabling Powering Up Resetting the Unit with the Reset ButtonDefault display cycle USP 507 Reset Mode Summary Mode Activation Result Purpose/NotesThree Special function buttons These four buttons are Front Panel OperationFront Panel Overview Picture control buttons These six buttons areSwitching Inputs Special Function Button OperationButton Backlighting FrontPanelOperation,co t’d USP 507 Menu SystemOverview of menus USP 507 Front Panel Operation NextSave a user preset Using the menusUser presets Recall a user presetInput configuration Settings for each signal formatOutput configuration Press Next or Menu to return to the Output ConfigurationImage capture/recall To capture an imageTo recall an image Advanced configuration To remove an image from the displayAdjust knob to turn the Auto Memory on or off. See -6 for View comm settings Edit comm settingsExit menu Setting the Front Panel Locks Executive Modes Scan converter configurationEnabling or disabling Executive mode 1 from the front panel Setting Up the USP 507 to Work with a Matrix Switcher USP 507 connected to a matrix switcherConnection must be via IP not RS-232 USP 507 Input #3 select the matrixRS-232 cable only Extron USPFour SIS Programmer’s Guide RS-232/RS-422 LinkEthernet LAN\⤀ Port Host-to-Processor Instructions Connection timeoutsUsing verbose mode Processor-Initiated MessagesProcessor Error Responses Using the Command/Response Table for SIS CommandsSIS Programmer’s Guide, cont’d Symbol definitions = SecamSIS Programmer’s Guide, cont’d Input Switching and Configuration Command Response Table for SIS CommandsCommand Ascii command Response Additional description $HSRTApix XphasTpix XalinX1%CONT X1% ColrX1%TINT X1%BRITX1* Zoom X1& HsizX1&VSIZ X1HPANX7%VTPO X2#OPOLX2$OSYN X7VSTDESX7&HDET ESX1&HSIZESX1&VSIZ ESX7&VDETX3&VDLY Advanced ConfigurationsX2TEST Front panel lockout executive mode\⤀PIP X5TIMEPicture in Picture Resets Information requestImage capture/recall to USP 507 flash memory Using the Command/Response Table for IP SIS Commands Command/Response Table for IP SIS Commands EFF WX12#CVECV EAEECJ WX12%CD~CJ Ethernet data portEDF Programmer’sGuide, cont’d ELFFive Starting the program Installing the programUSP 507 Software USP 507 USP 507 SoftwareUsing the Program OrientationFile menu USP 507 Software, cont’dControl program menus Options menuTools menu Download Now USP 507 USP 507 Software Help menu Sppcp Help file’s main windowControl tab Control tab screenConfiguration tab I/O Configuration tab screenAdvanced Settings tab Advanced Features Within this sectionScan Converter tab Scan Converter tab screenImage Capture tab Status barSix Start the Web browser program Accessing the Web PagesHtml Operation USP 507 Html OperationSystem Status System StatusIP Settings fields Configuration PagesSystem Settings Html Operation, cont’dGateway IP Address field Dhcp radio buttonsIP Address field Subnet Mask fieldDate/Time Settings fields Date/Time Settings fieldsScaler Settings Scaler settingsRGB delay, test pattern, and Edid selections Passwords PasswordsFirmware Upgrade Download product namefirmware version.exe buttonFile Management Choose file window with a firmware file selectedOther file management activities Uploading filesAdding a directory Delete all files Click Delete AllControl Pages User ControlMemory/Input Presets PIP Setup/PIP PresetsImages Image is not yet displayedReference Information AAppendix aSpecifications Reference InformationUSP 507 Reference Information Sync Reference Information, cont’d MtbfIncluded parts Part Numbers and AccessoriesAccessories Optional I/O boardsAppendixBB Ethernet Link Default addressEthernet Connection Ping to determine Extron IP addressConnect as a Telnet client Ping to determine Web IP addressUSP 507 Ethernet Connection Telnet tips Connecting to the USP 507 Open command\⤀Ethernet Connection, cont’d Escape character and Esc keyLocal and remote devices Subnetting a PrimerGateways IP addresses and octetsUnmasked octets are compared indicated by ? in figure B-6 Subnet masks and octetsDetermining whether devices are on the same subnet Masked octets are not compared indicated by X in figure B-6USA, Canada, South America Japan Central America Europe, Africa, and the Middle East ChinaAsia Middle East

USP 507 specifications

Extron Electronics has long been a leader in the field of professional AV system design, and one of their standout products is the USP 507. The USP 507 is an advanced universal speaker processor that is engineered to elevate audio performance across a variety of applications. Designed for both commercial and residential environments, the USP 507 combines cutting-edge technology with user-friendly features to deliver superior sound quality and precise audio control.

One of the main features of the USP 507 is its comprehensive signal processing capabilities. The device supports a range of audio formats and delivers 48 kHz or 96 kHz sample rates, ensuring high fidelity in audio reproduction. It also includes a configurable 5-band equalizer per channel, allowing users to fine-tune audio output to accommodate different room acoustics and speaker types.

The USP 507 is equipped with Extron’s patented SpeedMatch technology to enhance speaker performance and optimize audio clarity. This innovative technology automatically analyzes the audio signals and adjusts various parameters to compensate for environmental conditions, ensuring consistent sound quality across all outputs.

In terms of connectivity, the USP 507 offers a wide array of input and output options. It includes both balanced and unbalanced audio inputs to facilitate seamless integration with other audio equipment. Furthermore, the device provides multiple output zones, enabling simultaneous audio distribution to different areas within a facility.

The USP 507 features intuitive software for simplified setup and operation. The Extron Toolbelt application allows users to configure, manage, and monitor the speaker processor through an easy-to-navigate interface. This software enhances user experience by providing real-time diagnostics and seamless integration with other Extron devices.

Durability and reliability are also hallmarks of the USP 507. Built with high-quality materials, it is designed to withstand the demands of professional use while ensuring long-lasting performance. Additionally, the device comes equipped with advanced thermal management features to prevent overheating during extended operations.

In summary, the Extron USP 507 is a versatile universal speaker processor that combines advanced signal processing technologies, a user-friendly interface, and robust construction. Its ability to deliver superior audio performance makes it an ideal choice for various applications, ranging from corporate environments to high-end residential setups. With its comprehensive features and reliable performance, the USP 507 stands out as an essential tool for audio professionals seeking to enhance their sound experience.
Top Page Image Contents