Bunn CDS-3 service manual Service, Component Access

Page 21

SERVICE

This section provides procedures for testing and replacing various major components used in this dispenser should service become necessary. Refer to Troubleshooting for assistance in determining the cause of any prob- lem.

WARNING - Inspection, testing, and repair of electrical equipment should be performed only by qualified service personnel. The dispenser should be disconnected from the power source when servicing, except when electrical tests are required and the test procedure specifically states to connect the dispenser to the power source.

COMPONENT ACCESS

WARNING - Disconnect the dispenser from the power source before the removal of any panel or the replacement of any component.

All components are accessible by removal of the auger motor cover, lower drip tray, front cover and the left and right side covers.

Refer to the contents listing for component location.

Contents

 

Auger Motors

22

Auger Motor Capacitors

23

Auger Shaft Assembly

24

Auger ON/OFF Switches

26

Circuit Breaker

27

Compressor (CDS-2)

28

(Compressor, Compressor Start Capacitor, Compressor Start Relay, Thermal Overload Protector)

 

Compressor (CDS-3)

31

(Compressor, Compressor Start Capacitor, Compressor Start Relay, Thermal Overload Protector)

 

Contactor

34

Cooling Drum Alignment

35

Day/Night Switch

36

Dispenser ON/OFF Switch

37

Electronic Control

38

Fan

39

Fuse and Fuse Holder

40

ICE/OFF/NO ICE Switch

41

Lamp Cord Assembly

42

Lamp Cord Connector

43

Lamp Holder/Socket Assembly

44

L.E.D./Adjustment Board

45

Solenoids

46

Temperature Sensor Assembly

47

Torque Sensor Circuit Board

48

Transformer

49

Voltage Divider

50

Coolant Schematics

51

Electrical Schematics

54

21

27646 122200

 

Image 21
Contents Post Office BOX SPRINGFIELD, Illinois CDS-2 CDS-3Introduction ContentsUser Notices 12559.0003 00986.000228720.0000 27443.0000 User Notices 27664.0000CDSA-2 Only Electrical Requirements Site preparationHand Each cooling drum seal Initial setupAs shown Place Inside of each auger shaftApproximately Operating Controls Setting Time DAY/NIGHT TimerSetting Night Time Mode Operating ControlsUsing the Dispenser for Cold Liquid Products Using the Dispenser for GRANITA-TYPE ProductsOther Recommendations for Your Dispenser Recommended Daily Cleaning Sugar & Alcohol products Lubrication Recommended Weekly CleaningAssembly DisassemblyLubrication Faucet HandlesSnap it onto the assembly Auger assembly & Disassembly Early Augers onlyProblem Probable Cause Remedy TroubleshootingAuger Motor Capacitors Refer to Service Auger Motor Auger Motor won’t turn Auger ON/OFF SwitchesTime Delay Hopper Display Lights not on Circuit BreakerIng procedures. See Compressor not running Power cordWith adjustment Board L.E.D.s With an extension cord. Refer toProblem Probable Cause Become unusual. Auger Motors ProblemComponent Access ServiceTest Procedures Auger MotorsLocation Auger Motor Capacitors Auger Motor CapacitorAuger Shaft Assembly Auger Shaft AssemblyService Auger Shaft ASSEMBLYcont Volts ac for 120 volt models Volts ac for 230 volt models Auger ON/OFF SwitchesCircuit Breaker Remove the wires from the circuit breakerConnect the black wire from the compressor Dispenser chassis Two wire 230 volt modelsProperly discharged before proceeding Compressor Start Relay Refer to FIG120V Dispensers Remove run capacitor and discard Refer to a and reconnect the wiresCompressor Thermal P1819 Overload Protector Location Compressor & Components CDS-3Disconnect the fan leads from the main wiring harness Refer to a and reconnect the wires to the compressorRED from Relay T2 WHI from Relay T4 BLK from Relay T-5 Compressor Relay Terminals Contactor Electronic Control Cooling Drum Alignment SymptomsDAY/NIGHT Switch Dispenser ON/OFF Switch Dispenser ON/OFF SwitchElectronic Control Electronic ControlFAN Use cable ties to secure wires away from fan bladesFuse Holder Fuse and Fuse HolderICE/OFF/NO ICE Switches ICE/OFF/NO ICE SwitchesLamp Cord Assy Lamp Cord AssyUpper left side of the auger covers Test Procedures Lamp Cord ConnectorInside the hopper covers Lamp HOLDER/SOCKET AssemblyE.D./ Adjustment Board D./ADJUSTMENT BoardSolenoids SolenoidsTemperature Sensor Temperature SensorTorque Sensor Circuit Board P1341 Location Torque Sensor Circuit BoardRemove transformer and discard TransformerVoltage Divider ServiceCoolant Schematic Diagram CDS-2 Prior to S/N CDS Coolant Schematic Diagram CDS-3CDS 0019500 Up 27646 27646 Schematic Wiring Diagram for CDS-2 PAF Schematic Wiring Diagram for CDSA-2 PAF 27646 27646 27646
Related manuals
Manual 34 pages 32.1 Kb Manual 34 pages 40.35 Kb

CDS-3 specifications

The Bunn CDS-3 is a commercial coffee brewer renowned for its reliability, efficiency, and high-quality performance. Designed for busy environments such as cafés, restaurants, and convenience stores, it offers the perfect balance of capacity and functionality, making it ideal for high-demand situations.

One of the standout features of the Bunn CDS-3 is its ability to brew up to 3.8 gallons of coffee per hour. This impressive capacity meets the needs of busy establishments where a constant supply of fresh coffee is crucial. The brewer’s stainless steel construction not only ensures durability but also maintains temperature, thus preserving the coffee’s rich flavor and aroma.

The CDS-3 incorporates Bunn's patented brewing technology, including the "Pour-Over" method. This feature allows for easy operation and contributes to the even extraction of coffee grounds. The machine is equipped with a pre-infusion mode that saturates coffee grounds before brewing, enhancing extraction for a fuller, more complex flavor profile.

Temperature control is another vital characteristic of the Bunn CDS-3. It maintains the water temperature between 195°F to 205°F, the ideal range for optimal coffee brewing. The brewer’s internals are designed for rapid heating, ensuring that the water reaches the desired temperature quickly and consistently, which is essential for high-quality coffee production.

In terms of usability, the Bunn CDS-3 offers an intuitive interface, allowing staff to operate it with minimal training. The front-access design not only simplifies maintenance, but also makes it easy to refill water and perform routine cleaning. Furthermore, the large capacity coffee pots ensure that the brewed coffee can be stored efficiently, minimizing waste.

Equipped with a unique spray head system, the Bunn CDS-3 ensures uniform saturation of the coffee grounds. This feature supports optimal extraction, allowing users to produce a rich and flavorful brew that keeps customers coming back for more.

In summary, the Bunn CDS-3 is a well-engineered, commercial-grade coffee brewer that excels in high-demand environments. Its robust construction, advanced brewing technology, consistent temperature control, and user-friendly design make it a favorite among coffee enthusiasts and professionals alike, affirming its reputation as a reliable and effective solution for coffee brewing needs. Whether for a bustling café or a catering service, the Bunn CDS-3 delivers a consistently great cup of coffee every time.