Manitowoc Ice RF manual Section Installation Instructions Electrical Service, Voltage

Page 8

Section 2

Installation Instructions

 

 

Electrical Service

!Warning

All wiring must conform to local, state and national codes.

VOLTAGE

The maximum allowable voltage variation is ±10% of the rated voltage at ice machine start-up (when the electrical load is highest).

!Warning

The ice machine must be grounded in accordance with national and local electrical codes.

All electrical work, including wire routing and grounding, must conform to local, state and national electrical codes. The following precautions must be observed:

The ice machine must be grounded.

A separate fuse/circuit breaker must be provided for each ice machine.

A qualified electrician must determine proper wire size dependent upon location, materials used and length of run (minimum circuit ampacity can be used to help select the wire size).

The maximum allowable voltage variation is +/-10 of the rated voltage at ice machine start-up (when the electrical load is highest).

Check all ground screws in the control box and verify they are tight before starting the ice machine.

Important

Observe correct polarity of incoming line voltage. Incorrect polarity can lead to erratic ice machine operation.

FUSE/CIRCUIT BREAKER

A dedicated circuit and a separate fuse/circuit breaker are required for each ice machine.

GROUND FAULT CIRCUIT INTERRUPTER

We do not recommend the use of a GFCI/GFI circuit protection with our equipment. If a GFCI/GFI is required by code, use a GFCI/GFI breaker rather than outlet which is more prone to intermittent nuisance trips than panel circuit breakers.

MINIMUM POWER CORD SPECIFICATIONS

The wire size to the receptacle is dependent upon location, materials used, length of run, etc., so it must be determined by a qualified electrician. Local, state or national requirements will supersede our minimum requirements.

FOR UNITED KINGDOM ONLY

As the colors of the wires in the mains lead of the appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows:

The wire which is colored green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth

ground symbol

 

 

 

or colored green or green and yellow.

 

 

 

 

 

 

 

 

 

 

The wire colored blue must be connected to the terminal which is marked with the letter N or colored black.

The wire colored brown must be connected to the terminal which is marked with the letter L or colored red.

Part Number 000007644 3/11

8

Image 8
Contents Manitowoc This manual contains English and French textTable of Contents Table of Contents Section Maintenance Section Customer SupportTable of Contents Model Numbers RF2300 Bin Adapter InstallationSection General Information Section Installation Instructions Installation RequirementsLocation of Ice Machine Ice Machine Heat of RejectionTypical Water Supply Drain Installation Potable Water RequirementsWater Supply and Drain Line SIZING/ Connections Drain ConnectionsSection Installation Instructions Electrical Service Ground Fault Circuit InterrupterMinimum Power Cord Specifications VoltageQuietqube Remote Condensing Unit RF2300RPotential Personal Injury Situation Usage with NON-MANITOWOC Condensing UnitsFactory Equipment Refrigeration Amounts General Roof/Wall PenetrationRoute Refrigeration Tubing Line SET LengthLengthening or Reducing Line Set Lengths Service LoopSuction Line OIL Traps Installation Instructions Section Connecting the line setConnect the Line Set to the Remote Condensing Unit Connect the Line Set to the Ice Machine Head SectionLeak Check The Refrigeration System Open The Valves Prior To Starting The Ice MachineOpen Valves Torque ValuesInstallation Instructions Section Installation Check List Part Number 000007644 3/11 Section Operation RF0244/RF0266/RF0385/ RF0388/RF0399/RF0644 OperationSection Operation RFS0300 Operation RFS0650/RF1200/RF2300 OperationSection Maintenance Interior Cleaning and SanitizingExterior Cleaning Cleaning/Sanitizing ProcedureSection Maintenance Procedure to Clean Heavily Scaled Flake Ice MachinesMaintenance Section Removal of Parts for Cleaning/Sanitizing ICE Chute RemovalAir-Cooled Condenser Cleaning Manitowoc Cleaner and SanitizerICE Chute Switch Actuator Removal Arctic Pure Water Filter SystemChecklist Section Customer SupportCustomer Support Customer Support Section Commercial Ice Machine Warranty Limited Warranty What is CoveredResidential Ice Machine Limited Warranty WHO is Covered by this Limited WARRANTY?Section Instructions d’installation Table des matièresSection Généralités Section FonctionnementSection Service clientèle Table des matières suitePart Number 000007644 3/11 Références des modèles RF2300 Installation de l’adaptateur de bacSection Généralités Section Instructions d’installation Emplacement de la machine à glaçonsConditions requises d’installation Machine à glaçons Chaleur de rejetConditions Requises Pour L’EAU Potable RF1200R/RF2300R Installation de conduitesInstallation d’évacuation d’alimentation en eau type Conditions électriques requises Raccordements D’ÉVACUATIONFUSIBLE/DISJONCTEUR DifférentielInstructions d’installation Section Royaume-Uni uniquementMontants frigorifiques de l’équipement en usine Situation comportant un risque De blessure corporelleMontée OU Descente DE Conduites GénéralitésLongueur DES Conduites Boucle de service Siphons D’HUILE DE Conduite D’ASPIRATIONÉtape 4 Raccordement des conduites Connecter les conduites au condenseur à distanceÉtape 8 Exigences d’isolation Ouvrir les robinetsValeurs de couple de serrage Page Part Number 000007644 3/11 Section Fonctionnement RF0244/RF0266/RF0385/ RF0388/RF0399/RF0644 FonctionnementFonctionnement Section RFS0300 Fonctionnement RFS0650/RF1200/RF2300 FonctionnementEntretien Nettoyage et désinfection intérieursNettoyage extérieur Procédure de nettoyage et de désinfectionEntretien Section ’eau Uniquement Nettoyant EauDépose DE LA Goulotte À Glaçons Nettoyage du condenseur refroidi à l’air Système de filtration d’eau Arctic PureNettoyant et désinfectant Manitowoc Dépose DE L’ACTIONNEUR D’INTERRUPTEUR DE Goulotte À GlaçonsSection Service clientèle Liste de vérificationService clientèle Section Garantie Limitée Période DE Cette Garantie Limitée Service clientèle Section Section Service clientèle Manitowoc

RF specifications

Manitowoc Ice RF is a leading series in the ice-making industry, renowned for its innovative technologies and commitment to efficiency. Designed to meet the high demands of commercial food service operations, the RF model features a range of cutting-edge attributes that set it apart from competitors.

One of the main features of Manitowoc Ice RF is its advanced refrigeration system. The machine employs an Adaptive Harvest Control technology that ensures consistent ice quality by continually monitoring the ice-making process and adjusting accordingly. This results in reliable production of clear, hard ice cubes without the usual inconsistencies found in other machines.

The Manitowoc Ice RF models are designed with energy efficiency in mind. They utilize high-efficiency compressors and optimized insulation methods, significantly reducing energy consumption compared to traditional ice machines. This not only contributes to cost savings for businesses but also aligns with environmentally conscious practices, helping to reduce the overall carbon footprint.

Another notable characteristic of the RF series is its streamlined design, which allows for easy installation and maintenance. The machines are compact, making them ideal for establishments with limited space. The removable panels and accessible components simplify routine cleaning and servicing, ensuring the unit operates at peak performance and extends its life cycle.

Food safety is another focus of the Manitowoc Ice RF series. The machines incorporate an internal, easy-to-clean design that minimizes the risk of contamination. The anti-microbial protection on key surfaces helps prevent the growth of harmful bacteria, ensuring that the ice produced is safe for consumption.

In addition to its robust construction and technology, Manitowoc Ice RF offers various production capacities, catering to different business needs. Whether in a bustling restaurant, a hotel, or a convenience store, there is a model that fits the required ice production volume.

Overall, the Manitowoc Ice RF series combines state-of-the-art technology, energy efficiency, and ease of use to provide an exceptional ice-making solution for commercial establishments. Its commitment to quality and innovation makes it a preferred choice for businesses aiming to enhance their food service operations while maintaining high standards of safety and efficiency.