Manitowoc Ice S600M manual Installation Instructions Section Location of Ice Machine

Page 10

Installation Instructions

Section 2

 

 

Location of Ice Machine

The location selected for the ice machine must meet the following criteria. If any of these criteria are not met, select another location.

•The location must be free of airborne and other contaminants.

•The air temperature must be at least 35°F (1.6°C), but must not exceed 110°F (43.4°C).

•The location must not be near heat-generating equipment or in direct sunlight and must be protected from weather.

•The location must not obstruct air flow through or around the ice machine. Refer to the chart below for clearance requirements.

S600M

Water-Cooled*

Top/Sides

8" (20.3 cm)

Back

5" (12.7 cm)

*There is no minimum clearance required for water-cooled or remote ice machines. This value is recommended for efficient operation and servicing only.

!Caution

The ice machine must be protected if it will be subjected to temperatures below 32°F (0°C). Failure caused by exposure to freezing temperatures is not covered by the warranty. See “Removal from Service/Winterization”.

Ice Machine Heat of Rejection

Series

Heat of Rejection

Ice Machine

Air Conditioning

Peak

S600M

9000

13900

B.T.U./Hour

Because the heat of rejection varies during the ice making cycle, the figure shown is an average.

Ice machines, like other refrigeration equipment, reject heat through the condenser. It is helpful to know the amount of heat rejected by the ice machine when sizing air conditioning equipment where self-contained air- cooled ice machines are installed.

This information is also necessary when evaluating the benefits of using water-cooled or remote condensers to reduce air conditioning loads. The amount of heat added to an air conditioned environment by an ice machine using a water-cooled or remote condenser is negligible.

Knowing the amount of heat rejected is also important when sizing a cooling tower for a water-cooled condenser. Use the peak figure for sizing the cooling tower.

2-2

Part Number 80-1629-3

Page 9 Page 11
Image 10
Page 9 Page 11
Contents S600M Model Ice Machines Read These Before Proceeding Personal Injury PotentialTable of Contents Section General Information Section Installation InstructionsSection Maintenance Table of Contents Section Ice Machine OperationSection Before Calling For Service Model Numbers How to Read a Model NumberSection General Information Ice Cube SizesGeneral Information Section Accessories Section General Information Model/Serial Number Location Model/Serial Number LocationWarranty Coverage General Ice Machine DimensionsS600M WATER-COOLED ICE Machines Installation Instructions Section Location of Ice Machine Ice Machine Heat of RejectionMinimum Circuit Ampacity Section Installation Instructions Electrical ServiceVoltage Electrical RequirementsSelf Contained ICE Machine 208-230/3/60 For United Kingdom OnlySelf Contained ICE Machine 115/1/60 or 208-230/1/60 Self Contained ICE Machine 230/1/50Water Inlet Lines Cooling Tower ApplicationsWater Supply Drain ConnectionsTypical Water Supply Drain Installation Installation Instructions SectionWater Supply and Drain Line SIZING/CONNECTIONS Section Installation Instructions Installation Check List AuCS Automatic Cleaning System Potential Personal Injury SituationSection Ice Machine Operation Component IdentificationIce Machine Operation Section Sequence Of Operation Initial START-UP or START-UP After Automatic SHUT-OFFHarvest Safety TimersHarvest Sequence 5. Water Purge Automatic SHUT-OFF 7. Automatic Shut-OffICE Thickness Check Ice Machine Operation Section Operational ChecksWater Level Ice Thickness CheckWater Purge Adjustment Harvest Sequence Water PurgeIce Machine Operation Section Water-Cooled Condenser Water Regulating Valve Exterior CleaningIce Machine Inspection AlphaSan→Sachet Replacement Procedure Maintenance Section GuardianGuardian Sachet Replacement Frequency Clean UP Procedure for Damaged Sachet PacketCleaning Procedure Section Maintenance Interior Cleaning and SanitizingStep Maintenance Section Sanitizing ProcedureRemoval of Parts for CLEANING/SANITIZING Water Curtain Removal Ice Thickness Probe Water CurtainIce Thickness Probe Removal Water Trough Water Distribution TubeWater Distribution Tube Removal Water Pump Water Level ProbeWater Pump Removal Dump Valve Disassembly Water Dump ValveEvaporator Tray Removal Drain Line Check ValveRemoving the Front Panels Water Inlet ValvePry Open the Water Regulating Valve AUCS→ Accessory Maintenance Section Removal from Service/WinterizationWATER-COOLED ICE Machines Section Before Calling For Service ChecklistBefore Calling For Service Section Safety Limit FeatureThis page Intentionally Left Blank Before Calling For Service Section Page Manitowoc ICE, INC

S600M specifications

The Manitowoc Ice S600M is a standout model in the ice machine market, recognized for its high performance, innovative features, and reliability. Designed specifically for restaurants, bars, and various foodservice operations, this ice machine offers a range of capabilities that cater to the diverse needs of commercial establishments.

One of the key features of the Manitowoc S600M is its impressive ice production capacity. It can produce up to 550 pounds of ice in a 24-hour period, making it suitable for busy environments where high volumes of ice are needed. The machine utilizes a modular design, allowing it to work seamlessly with different storage bins and provides flexibility in placement.

The S600M is equipped with advanced technologies that enhance efficiency and ease of use. One notable technology is the Smart LED lighting, which ensures users can easily monitor and maintain the equipment. This smart feature provides real-time indications regarding the ice production process, alerting operators to issues such as water supply problems or the need for maintenance.

Another significant aspect of the S600M is its energy efficiency. The machine is designed with innovative insulation that minimizes temperature fluctuations, thereby reducing energy consumption. This not only contributes to lower operational costs but also aligns with environmentally friendly practices—a crucial consideration for modern businesses.

In terms of the ice itself, the Manitowoc S600M produces traditional cube-shaped ice, known for its slower melting rate and ideal for various drinks and cocktails. This type of ice is essential for maintaining beverage quality over extended periods, making it a popular choice among foodservice operators.

The machine is also designed with ease of maintenance in mind. It features a self-contained refrigeration system and removable panels, allowing for easy access to internal components. This design minimizes downtime and facilitates regular cleaning and maintenance, ensuring consistent ice production.

In summary, the Manitowoc Ice S600M is an exceptional choice for businesses seeking a reliable and efficient ice machine. With its high production capacity, advanced technologies, energy efficiency, and user-friendly design, it meets the contemporary demands of the foodservice industry. Investing in the S600M means ensuring an uninterrupted supply of quality ice, essential for exceptional customer service and operational success.
Top Page Image Contents