Manitowoc Ice S600M manual Removing the Front Panels, Water Inlet Valve

Page 33

Section 4

Maintenance

 

 

Water Inlet Valve

The water inlet valve normally does not require removal for cleaning. Refer to Section 5 for a list of causes for “No Water Entering Water Trough” or “Water Overflows Water Trough.

1.When the ice machine is off, the water inlet valve must completely stop water flow into the machine.

2.When the ice machine is on, the water inlet valve must allow the proper water flow through it. Set the toggle switch to ON. Watch for water flow into the ice machine. If the water flow is slow or only trickles into the ice machine, refer to Section 5.

Follow the procedure below to remove the water inlet valve.

!Warning

Disconnect the electric power to the ice machine and dispenser at the electric service switch box and turn off the water supply before proceeding.

1.Remove the 1/4” hex head screws.

2.Remove, clean, and install the filter screen.

FILTER

ACCESS

SCREWS

WATER

INLET

VALVE

SV1622

Removing the Front Panels

NOTE: The front panels do not normally have to be removed. If needed perform the following procedure.

1.Loosen screws. Do not remove they are retained by o-rings to prevent loss.

2.30 Inch and 48 Inch Models Only: To remove right front door lift up and remove (22 inch machines have a single door, proceed to step 3).

5

3

2

Door Removal

3.Open left front door to 45 degrees.

4.Support with left hand, depress top pin, tilt top of door forward and lift out of bottom pin to remove.

Part Number 80-1629-3

4-11

Page 32 Page 34
Image 33
Page 32 Page 34
Contents S600M Model Ice Machines Personal Injury Potential Read These Before ProceedingSection Installation Instructions Table of Contents Section General InformationTable of Contents Section Ice Machine Operation Section MaintenanceSection Before Calling For Service Section General Information How to Read a Model NumberModel Numbers Ice Cube SizesGeneral Information Section Accessories Model/Serial Number Location Section General Information Model/Serial Number LocationWarranty Coverage Ice Machine Dimensions GeneralS600M WATER-COOLED ICE Machines Ice Machine Heat of Rejection Installation Instructions Section Location of Ice MachineVoltage Section Installation Instructions Electrical ServiceMinimum Circuit Ampacity Electrical RequirementsSelf Contained ICE Machine 115/1/60 or 208-230/1/60 For United Kingdom OnlySelf Contained ICE Machine 208-230/3/60 Self Contained ICE Machine 230/1/50Water Supply Cooling Tower ApplicationsWater Inlet Lines Drain ConnectionsInstallation Instructions Section Typical Water Supply Drain InstallationWater Supply and Drain Line SIZING/CONNECTIONS Section Installation Instructions Installation Check List Potential Personal Injury Situation AuCS Automatic Cleaning SystemComponent Identification Section Ice Machine OperationInitial START-UP or START-UP After Automatic SHUT-OFF Ice Machine Operation Section Sequence Of OperationHarvest Sequence 5. Water Purge Safety TimersHarvest Automatic SHUT-OFF 7. Automatic Shut-OffWater Level Ice Machine Operation Section Operational ChecksICE Thickness Check Ice Thickness CheckHarvest Sequence Water Purge Water Purge AdjustmentIce Machine Operation Section Ice Machine Inspection Exterior CleaningWater-Cooled Condenser Water Regulating Valve AlphaSan→Guardian Sachet Replacement Frequency Maintenance Section GuardianSachet Replacement Procedure Clean UP Procedure for Damaged Sachet PacketSection Maintenance Interior Cleaning and Sanitizing Cleaning ProcedureStep Sanitizing Procedure Maintenance SectionRemoval of Parts for CLEANING/SANITIZING Water Curtain Water Curtain Removal Ice Thickness ProbeIce Thickness Probe Removal Water Distribution Tube Water TroughWater Distribution Tube Removal Water Level Probe Water PumpWater Pump Removal Water Dump Valve Dump Valve DisassemblyDrain Line Check Valve Evaporator Tray RemovalWater Inlet Valve Removing the Front PanelsMaintenance Section Removal from Service/Winterization Pry Open the Water Regulating Valve AUCS→ AccessoryWATER-COOLED ICE Machines Checklist Section Before Calling For ServiceSafety Limit Feature Before Calling For Service SectionThis page Intentionally Left Blank Before Calling For Service Section Page Manitowoc ICE, INC

S600M specifications

The Manitowoc Ice S600M is a standout model in the ice machine market, recognized for its high performance, innovative features, and reliability. Designed specifically for restaurants, bars, and various foodservice operations, this ice machine offers a range of capabilities that cater to the diverse needs of commercial establishments.

One of the key features of the Manitowoc S600M is its impressive ice production capacity. It can produce up to 550 pounds of ice in a 24-hour period, making it suitable for busy environments where high volumes of ice are needed. The machine utilizes a modular design, allowing it to work seamlessly with different storage bins and provides flexibility in placement.

The S600M is equipped with advanced technologies that enhance efficiency and ease of use. One notable technology is the Smart LED lighting, which ensures users can easily monitor and maintain the equipment. This smart feature provides real-time indications regarding the ice production process, alerting operators to issues such as water supply problems or the need for maintenance.

Another significant aspect of the S600M is its energy efficiency. The machine is designed with innovative insulation that minimizes temperature fluctuations, thereby reducing energy consumption. This not only contributes to lower operational costs but also aligns with environmentally friendly practices—a crucial consideration for modern businesses.

In terms of the ice itself, the Manitowoc S600M produces traditional cube-shaped ice, known for its slower melting rate and ideal for various drinks and cocktails. This type of ice is essential for maintaining beverage quality over extended periods, making it a popular choice among foodservice operators.

The machine is also designed with ease of maintenance in mind. It features a self-contained refrigeration system and removable panels, allowing for easy access to internal components. This design minimizes downtime and facilitates regular cleaning and maintenance, ensuring consistent ice production.

In summary, the Manitowoc Ice S600M is an exceptional choice for businesses seeking a reliable and efficient ice machine. With its high production capacity, advanced technologies, energy efficiency, and user-friendly design, it meets the contemporary demands of the foodservice industry. Investing in the S600M means ensuring an uninterrupted supply of quality ice, essential for exceptional customer service and operational success.
Top Page Image Contents