Graco 3A0237L important safety instructions Electric Shock Hazard

Page 11

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

ELECTRIC SHOCK HAZARD

The hoses must be grounded. Improper grounding, set-up or usage of the hoses can cause electric shock.

•Turn off and disconnect power before disconnecting before installing or servicing hoses.

•Connect to grounded power source.

•All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.

•Never cut or puncture a hose cover.

•Do not expose to rain. Store indoors.

SKIN INJECTION HAZARD

High-pressure fluid from hose leaks, or ruptured components will pierce skin. This may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

•Inspect hose before each use for cuts, bulges, kinks or any other damage.

•Replace hoses proactively at regular intervals based on your operating conditions.

•Replace damaged hose immediately.

•Tighten all fluid connections before operating the equipment.

•Keep clear of leaks.

•Do not stop or deflect leaks with your hand, body, glove, or rag.

•Never exceed hose Maximum Pressure or Temperature ratings.

•Only use chemicals that are compatible with wetted parts. See Technical Data in this manual. Read MSDSs and fluid and solvent manufacturer’s recommendations.

•Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing equipment.

THERMAL EXPANSION HAZARD

Fluids subjected to heat in confined spaces, including hoses, can create a rapid rise in pressure due to the thermal expansion. Over-pressurization can result in equipment rupture and serious injury.

•Open a valve to relieve the fluid expansion during heating.

•Replace hoses proactively at regular intervals based on your operating conditions.

BURN HAZARD

Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns:

• Do not touch hot fluid or equipment.

3A0237L

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Heated Hoses Applicator Kits Important Safety InstructionsRelated Manuals ContentsCarbon Steel Dual Heat Zone Hose Bundle with Air Hose Heated Hose Bundle Part NumbersFittings Fluid Temperature Sensor FTSHeated Whip Hose Side Heated Hoses Red Individual HosesIndividual a Side Heated Whip Hose Side Unheated Hoses RedSide Heated Hoses Blue Individual B Side Heated Whip Hose Side Unheated Hoses BlueApplicator Kits See manual MD2 Valve Applicator KitsMD2 Handle Chemical Connection Kit Electric Shock Hazard Toxic Fluid or Fumes Hazard Personal Protective Equipment Important Two-Component Material Information Changing Materials B ComponentsConnect Whip Hose to Gun or Gun Manifold InstallationDescription Single Heat Zone with a or B Heated Hose Connect Heated HosesSingle Heat Zone with a and B Heated Hose Dual Heat Zone with a and B Heated HoseIncorrect Correct Insert Wire and SetscrewSee Connect FTS and Heated Whip Hose, Cap plugs SetscrewsConnect FTS and Heated Whip Hose Connect Splitter Connect Solenoid KitProtective Covering Check Hoses for LeaksSingle Heat Zone Shown OperationInstructions for Replacing Individual a or B Hose MaintenanceClean Orifice Follow Pressure Relief Procedure in MD2 valve manualMaintenance 3A0237L For Single Zone Heated Whip Hose Bundles Bundle Individual Whip HosesSide Dual Heat Zone Heated Whip Hose BundleSingle Heat Zone Heated Whip Hose Bundle Bundle Individual Heated Hoses Machine End Dual Heat Zone Heated Hose Bundle ShownSingle Heat Zone Heated Whip Hose PartsWhip Hoses Dual Heat Zone Heated Whip HoseHeated Whip Hoses Heated Hose Bundles Varied Parts Dual Zone Heated Hose BundlesSingle Zone Heated Hose Bundles Stainless Steel Fluid Temperature Sensor Using Fluid Temperature Sensors For Single Heat ZonesUsing Fluid Temperature Sensors for Dual Heat Zones Carbon Steel Fluid Temperature SensorConnect 258758 , 15F144 Hose Wire JumperPart Description Qty 24E505 Orifice Block Kit MD2 Applicator KitsMD2 Applicator Kits 153 24D162 Stainless Steel Connection Kit24C757 Machine Mount Kit AccessoriesScuff Guard Solenoid KitsOnly 24D160 24D160 Remote Mount MD2 Kit 24D161 Remote Mount Fusion KitOnly 24D161 Category Data Technical DataTechnical Data 3A0237L Graco Information Graco Standard Warranty
Top Page Image Contents