Graco 3A0237L important safety instructions Toxic Fluid or Fumes Hazard

Page 12

Warnings

WARNING

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

Read MSDSs to know the specific hazards of the fluids you are using.

Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

Always wear chemically impermeable gloves when spraying, dispensing, or cleaning equipment.

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop cloths (potential static arc).

Keep work area free of debris, including solvent, rags and gasoline.

Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are present.

Ground all equipment in the work area. See Grounding instructions.

Use only grounded hoses.

Hold gun firmly to side of grounded pail when triggering into pail.

If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until you identify and correct the problem.

Keep a working fire extinguisher in the work area.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

Do not operate the unit when fatigued or under the influence of drugs or alcohol.

Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.

Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.

Do not leave the work area while equipment is energized or under pressure. Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

Do not alter or modify equipment.

Use equipment only for its intended purpose. Call your distributor for information.

Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

Do not kink or over bend hoses or use hoses to pull equipment.

Keep children and animals away from work area.

Comply with all applicable safety regulations.

12

3A0237L

Image 12
Contents Important Safety Instructions Heated Hoses Applicator KitsContents Related ManualsHeated Hose Bundle Part Numbers Carbon Steel Dual Heat Zone Hose Bundle with Air HoseFluid Temperature Sensor FTS Heated Whip HoseFittings Individual Hoses Side Heated Hoses RedSide Unheated Hoses Red Individual a Side Heated Whip HoseSide Heated Hoses Blue Side Unheated Hoses Blue Individual B Side Heated Whip HoseApplicator Kits MD2 Valve Applicator Kits MD2 Handle Chemical Connection KitSee manual Electric Shock Hazard Toxic Fluid or Fumes Hazard Personal Protective Equipment Important Two-Component Material Information B Components Changing MaterialsInstallation DescriptionConnect Whip Hose to Gun or Gun Manifold Connect Heated Hoses Single Heat Zone with a and B Heated HoseDual Heat Zone with a and B Heated Hose Single Heat Zone with a or B Heated HoseInsert Wire and Setscrew Incorrect CorrectCap plugs Setscrews See Connect FTS and Heated Whip Hose,Connect FTS and Heated Whip Hose Connect Solenoid Kit Connect SplitterCheck Hoses for Leaks Protective CoveringOperation Single Heat Zone ShownMaintenance Clean OrificeFollow Pressure Relief Procedure in MD2 valve manual Instructions for Replacing Individual a or B HoseMaintenance 3A0237L Bundle Individual Whip Hoses For Single Zone Heated Whip Hose BundlesDual Heat Zone Heated Whip Hose Bundle Single Heat Zone Heated Whip Hose BundleSide Bundle Individual Heated Hoses Dual Heat Zone Heated Hose Bundle Shown Machine EndParts Whip HosesDual Heat Zone Heated Whip Hose Single Heat Zone Heated Whip HoseHeated Whip Hoses Heated Hose Bundles Dual Zone Heated Hose Bundles Varied PartsSingle Zone Heated Hose Bundles Using Fluid Temperature Sensors For Single Heat Zones Using Fluid Temperature Sensors for Dual Heat ZonesCarbon Steel Fluid Temperature Sensor Stainless Steel Fluid Temperature Sensor15F144 Hose Wire Jumper Part Description QtyConnect 258758 , MD2 Applicator Kits MD2 Applicator Kits153 24D162 Stainless Steel Connection Kit 24E505 Orifice Block KitAccessories Scuff GuardSolenoid Kits 24C757 Machine Mount Kit24D160 Remote Mount MD2 Kit 24D161 Remote Mount Fusion Kit Only 24D161Only 24D160 Technical Data Category DataTechnical Data 3A0237L Graco Standard Warranty Graco Information