Connection of Manifolds in Battery

Two or more ranges can be coupled together at the manifold by removing the front control panel to make necessary connections. Be sure to cap open ends. To connect:

1.Adjust manifold by loosening U-bolts. In a large battery of eight or more ranges, gas should be fed from both ends of the battery. "T" gas connections can be installed whenever necessary for increased gas supply. For further details, consult your gas company. The top roll front may also be removed for your convenience.

2.Bolt risers together at top rear.

3.If risers have high shelves, bolt the high shelf brackets together. Replace the high shelves.

4.Use clamp to pull ranges together at the rear. (There is a slotted hole in the top frame side at the rear that can be used to bolt ranges together if necessary. Run a 5/16 " (8 mm) diameter drill through the slotted hole, drilling from inside out on each range.) Use 1/4" (6 mm)-2 x 2" (51 mm) bolt that is provided.

5.Replace all top sections. Make manifold union connections at the front. Do not allow manifold pipe to turn.

6.Bolt the roll front ends together at the front. (Make sure roll fronts match.) Use 1/4" (6 mm)-20 x 1" (25 mm) bolts provided.

7.Tighten the front roll front bolts after the roll front ends have been properly bolted together.

8.Before replacing manifold panels, check all gas connections for leaks. (See GAS CONNECTIONS in this manual.)

If appliance has rear gas connection, carefully check for open gas lines.

The gas pressure regulator must have proper outlet pressure capacity for this battery application.

INSTALLING OVERLAPPING GRIDDLETOP

1.Bolt ranges together and level per instructions in this manual.

2.Remove chrome bull noses from ranges receiving overlapping griddle tops. Bull noses are held by bolts on the bottom side.

3.MANUAL CONTROLS ONLY — Set griddle tops in place and level with bolts located under the griddle top in both rear corners. Should you desire griddle plate to slope forward, adjust accordingly. Make sure hole in front gutter ts into drain in range. Reinstall bull noses.

4.THERMOSTAT CONTROL ONLY — Set griddle top in place and support front with 4" to 6" (102

to 152 mm) blocks. Insert thermostat probe into smaller of two angles on bottom of griddle top (bend probe slightly while inserting to hold in place). Slide insulation sleeving around probe lead up to angle on griddle top. Coil excess lead near thermostat, leaving as little as possible in burner area. Make sure that thermostat probe lead is not over burner or pilot ame. Remove supporting blocks and lower griddle top in place.

Level griddle top with bolts located under both rear corners. Should you desire griddle plate to slope forward, adjust accordingly. Make sure hole in front gutter ts into drain in range. Reinstall bull noses.

Leveling bolts are provided under each griddle plate at the rear, should you desire griddle plate to slope forward. Top frame sealing channels are supplied to seal o any space between two or more ranges.

— 7 —

FK, FK36_A specifications

The Vulcan-Hart FK36_A,FK is a commercial-grade gas-fired fryer designed for efficiency, durability, and safety in busy kitchen environments. Renowned for its robust construction and advanced features, it stands as a popular choice among chefs and restaurant operators looking to elevate their frying capabilities.

At the heart of the FK36_A,FK is its impressive heating technology. The fryer is equipped with high-performance gas burners that provide rapid heating, allowing for quick recovery times. This means chefs can maintain optimal frying temperatures even during peak service hours. The fryer's adjustable temperature settings range from 200°F to 400°F, making it versatile enough for a variety of food preparations, from delicate pastries to hearty proteins.

One of the standout features of the Vulcan-Hart FK36_A,FK is its large capacity, with a fry pot that holds up to 35 pounds of oil. This substantial size is ideal for high-volume frying, accommodating the needs of busy restaurants, food trucks, and catering services. Additionally, the fryer comes with a built-in filtration system that helps extend the life of the cooking oil, reduces waste, and improves food quality by minimizing flavor transfer between uses.

The FK36_A,FK also emphasizes safety with its cool-to-the-touch fry tank design, which helps prevent burns and accidents in fast-paced kitchen environments. An integrated high-limit temperature control safeguards against overheating, ensuring that both food and equipment are protected. Its durable stainless steel construction not only enhances its longevity but also simplifies cleaning and maintenance, making it a practical choice for operators.

In terms of technology, the Vulcan-Hart FK36_A,FK features a user-friendly digital control panel that allows for easy adjustments and monitoring of cooking temperatures. This intuitive interface contributes to consistent results and ensures that operators can focus on delivering high-quality dishes without the worry of complicated settings.

Overall, the Vulcan-Hart FK36_A,FK is a powerhouse fryer that combines innovative technology with practical features tailored for today's professional kitchens. From its high-capacity design and advanced heating systems to its safety and maintenance attributes, it is an exemplary solution for any establishment aiming to provide exceptional fried foods while maintaining peak operational efficiency.