GE ZV830 Secure the junction box cover with the 6 original screws, Remove protective plastic

Page 17

Installation Instructions

INSTALLATION—RECIRCULATING

6 CONNECT ELECTRICAL

Verify that power is turned off at the source.

WARNING:If house wiring is not 2-wire with a ground wire, a ground must be provided by the installer. When house wiring is aluminum, be sure to use U.L. approved anti-oxidant compound and aluminum-to-copper connectors.

Remove the 6 screws on the junction box cover and the knockout on the top or left side.

Junction

box cover

Secure the house wiring to the junction box with a strain relief.

Connect the white lead to the branch circuit white lead.

Connect the black lead to the branch circuit black lead.

Connect the green/yellow lead to the branch circuit green lead or bare ground lead.

Secure all the connections with wire nuts on each electrical connector.

Push the wires into the junction box and replace the cover. Be sure the wires are not pinched.

Secure the junction box cover with the 6 original screws.

17

7 INSTALL DUCT COVERS

Remove protective plastic

Mounting

covering.

screws

Place the decorative duct

 

covers on top of the hood.

 

NOTE: The inside piece has vent

Vent holes

holes on one end intended for

use when the hood is installed

 

for recirculating purposes. Be sure the vented end is at the top; the vent holes will be visible in this installation.

The inside duct piece must slip

into the folded ends on the outer section.

Upper

Duct cover

duct cover

support bracket

Lower duct cover

 

Duct attachment

Lower duct

tabs

cover seat

 

Extend the inner duct upward to the ceiling bracket .

Screw holes

Press up on the front corners of the filter cover panel to unlock. Lower the panel to access the filter.

Locate the screw holes on the inside front edge of the opening. Install 2 screws to secure the duct cover to the hood.

Image 17
Contents Instrucciones de instalación Instructions d’installationRead these instructions completely and carefully Read and Save These Instructions Before YOU BeginCompletion Time 1 to 3 Hours Installation Options ContentsAdvance Planning Power SupplyAccessory Duct Cover Do not use flexible plastic ducting Duct FittingsFlexible ducting Tools and Materials Required not Supplied Remove the PackagingAccessories Determine Installation HeightWall Mount ZV830 Installation Heights PossibleLocate and count Screws Duct cover Check Installation Hardware28-7/8 ″ 10-7/8 ″DUCTWORK, Wiring Locations INSTALLATION-VENTED to the OutsideInstall Framing for Hood Support House Wiring LocationInstall Duct Bracket Install Hood Mounting ScrewsMount the Hood Secure the bracket to the wallConnect Ductwork Connect Electrical Install Duct CoversVerify that power is turned off at the source Finalize Installation Install FiltersImportant Framing must be capable of supporting 100 lbs INSTALLATION-RECIRCULATINGTape the template in position along the penciled line Check to be sure the mounting screws are horizontally level Size and CUT Duct Piece Outlet Hold the assembly against Duct bracketRemove protective plastic Secure the junction box cover with the 6 original screwsCovering Place the decorative duct Covers on top of the hoodRemove all tape and packing material Installation Instructions Installation Instructions Avertissement Lisez ET Conservez CES Instructions Avant DE CommencerAvertissement Pour Réduire Avertissement Afin DE RéduireOptions D’INSTALLATION Dimensions ET IntervallesTable DES Matières 28 cm 10-7/8 poAlimentation Accessoire Cache ConduitPlanification ’utilisez PAS de conduit en plastique flexible Raccords DE CanalisationRetirer L’EMBALLAGE Outils ET Matériaux NécessairesNON Fournis Serre-filsAccessoires Définition DE LA Hauteur ’INSTALLATIONSupport mural ZV830 Hauteurs d’installation HauteurRepérez et comptez les vis Vérification DU Matériel D’INSTALLATIONEmplacement DES Câbles DE LA Maison INSTALLATION-VENTILÉ Vers L’EXTÉRIEURConduit de plafond Conduit muralInstallez Les vis Trou de ligne médiane Installer LE Support DE CanalisationMonter LA Hotte Fixez le support sur le murFlux d’air Connecter LA CanalisationCache de Boîte à bornes Vérifiez que l’alimentation est coupée à la sourceSupport de cache Conduit Trous de visTerminer L’INSTALLATION Installer LES FiltresINSTALLATION- Recyclage Monter LA Hotte Les sorties de la hotte Mesurer ET Couper LE ConduitLongueur Conduit Du déflecteurCache Connecter LES Parties ÉlectriquesSupérieur Cache conduit Inférieur Vérifiez que l’alimentation est coupée à la sourceInstaller LES Filtres Instructions d’installation Instructions d’installation Instructions d’installation Precaución Guarde Estas Instrucciones Antes DE EmpezarAdvertencia Tiempo para la instalación 1 a 3 horasOpciones DE Instalación Contenidos10-7/8 Altura Hasta el 24 Mín 30 Máx 18-7/8 29-7/8Fuente DE Energía Planificación PreviaAccesorio DE Cubierta DE Conducto Instrucciones de conexión a tierraAccesorios Para Conductos Del ducto Dimensiones Equivalente Utilizada TotalLongitud Pieza Longitud CantidadNo Incluido Herramientas Y Materiales RequeridosQuite EL Envoltorio Accesorios Establezca LA Altura DE InstalaciónAlturas de instalación De montaje de pared de ZV830 Altura deControle LOS Elementos Para LA Instalación Ubicación DE LOS Conductos Y Cableado INSTALACIÓN-VENTILACIÓN Hacia EL ExteriorInstale EL Armazón Para EL Soporte DE LA Campana Ubicación DE Cableado DomésticoInstale LOS Tornillos DE Montaje DE LA Campana Instale LA CampanaQuite la plantilla Instale EL Soporte DEL ConductoConecte EL Conducto Instale LAS Cubiertas DE LOS Conductos Orificios para Tornillos Instale LOS FiltrosFinalice LA Instalación Ubicación del INSTALACIÓN-RECIRCULACIÓNCableado Doméstico El cielorrasoPencil Line Indicating De medida LongitudCubierta de conducto i nferior Quite la tapa protectora de PlásticoOrificios de ventilación serán visibles en esta instalación Instale LOS Filtros Notas Notas Para servicio técnico local Monogram en su área, llame al GE Consumer & Industrial
Related manuals
Manual 40 pages 46.91 Kb

ZV830 specifications

The GE ZV830 is a groundbreaking and sophisticated addition to the lineup of kitchen appliances, designed to elevate both functionality and aesthetics. Packed with a range of advanced features, the ZV830 stands out as a state-of-the-art microwave that not only meets but exceeds modern culinary demands.

One of the standout characteristics of the GE ZV830 is its sleek and modern design, which seamlessly integrates into any kitchen decor. The appliance features a stainless-steel finish that is not only visually appealing but also easy to clean, making it a practical choice for busy homeowners. The unit is designed for installation over a range or cooktop, freeing up counter space while providing powerful cooking capabilities.

The ZV830 is equipped with a robust 1.7 cubic feet capacity, providing ample space for cooking large dishes or multiple items simultaneously. This microwave offers an impressive 1,000 watts of cooking power, ensuring quick and efficient heating, defrosting, and cooking of food.

One of the key technologies implemented in the GE ZV830 is its sensor cooking feature. This advanced technology allows the microwave to automatically adjust cooking times and power levels based on the moisture released from the food. As a result, users can achieve perfectly cooked meals without the guesswork traditionally associated with microwave cooking.

Additionally, the GE ZV830 boasts a range of convenient cooking presets and auto-reheat options, streamlining meal preparation. Features such as popcorn settings and pizza reheating options make it a versatile tool for any kitchen. The unit also includes a dedicated steam function, which is perfect for health-conscious individuals looking to prepare steamed vegetables easily.

Highly regarded for its user-friendly interface, the GE ZV830 includes a large LED display that provides clear visibility of cooking settings and times. The straightforward keypad allows for easy input, making it accessible for all users, including those less familiar with kitchen technology.

Furthermore, the GE ZV830 is designed with safety in mind. It includes child lock features to prevent unintended use, offering peace of mind for families. In conclusion, the GE ZV830 is an exemplary microwave that combines design, performance, and innovative technology to enhance the cooking experience. Its advanced features and user-centric design make it a valuable addition to any modern kitchen.