GE ZV830 manual Advance Planning, Power Supply, Accessory Duct Cover

Page 4

Installation Preparation

ADVANCE PLANNING

• Determine the exact location of the vent hood.

• Install a wall cap with damper or roof cap at the exterior

• Plan the route for venting exhaust to the outdoors.

opening. Order the wall or roof cap and any transition

• Use the shortest and straightest duct route possible. For

needed in advance.

Wall Framing for Adequate Support

satisfactory performance, duct run should not exceed 100 ft.

equivalent length for any duct configurations.

• This vent hood is heavy. Adequate structural support must

• Refer to “Duct Fittings” chart on page 5 to compute the

be provided in all types of installations. The hood must be

maximum permissible length for duct runs to the outdoors.

secured to vertical studs in the wall, or to a horizontal

CAUTION:To reduce risk of fire and to properly

support.

• The vent hood should be on site before final framing and

exhaust air, be sure to duct air outside—do not vent exhaust

wall finishing. This will help to accurately locate the duct

air into spaces within walls or ceilings or into attics, crawl

work and electrical service.

spaces or garages.

• Installation will be easier if the vent hood is installed before

WARNING: TO REDUCE THE RISK OF FIRE,

the cooktop and countertop are installed.

 

USE ONLY METAL DUCTWORK.

ACCESSORY DUCT COVER

 

This hood is shipped with a decorative duct cover for ceiling

 

heights of 7′11″ to 10′. The ZX83012 duct cover accessory

 

is available to reach ceiling heights between 10′1″ and 12′.

 

The accessory should be ordered with the hood and be

 

on site before installation begins.

 

 

 

 

POWER SUPPLY

Grounding instructions

IMPORTANT – (Please read carefully)

WARNING: FOR PERSONAL SAFETY,

The grounding conductor must be connected to a grounded

metal, permanent wiring system, or an equipment-grounding

THIS APPLIANCE MUST BE PROPERLY GROUNDED.

terminal or lead on the hood.

Remove house fuse or open circuit breaker before beginning

WARNING:The improper connection of the

installation.

Do not use an extension cord or adapter plug with this

equipment-grounding conductor can result in a risk of

appliance. Follow National electrical codes or prevailing local

electric shock. Check with a qualified electrician or service

codes and ordinances.

representative if you are in doubt whether the appliance is

Electrical supply

properly grounded.

CAUTION:Automatically Operated Device –

These vent hoods must be supplied with 120V, 60Hz, and

connected to an individual, properly grounded branch circuit,

To reduce the risk of injury disconnect from power supply

and protected by a 15 or 20 amp circuit breaker or time

before servicing. This unit is equipped with an integral

delay fuse.

disconnecting switch located inside the blower housing.

• Wiring must be 2 wire with ground.

 

• If the electrical supply does not meet the above

 

requirements, call a licensed electrician before proceeding.

 

• Route house wiring as close to the installation location as

 

possible, in the ceiling or back wall. Refer to Wiring Locations

 

on page 9.

 

• Connect the hood wiring to the house wiring in accordance

 

with local codes.

 

 

 

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Instructions d’installation Instrucciones de instalaciónCompletion Time 1 to 3 Hours Read and Save These Instructions Before YOU BeginRead these instructions completely and carefully Contents Installation OptionsAccessory Duct Cover Power SupplyAdvance Planning Flexible ducting Duct FittingsDo not use flexible plastic ducting Remove the Packaging Tools and Materials Required not SuppliedDetermine Installation Height AccessoriesWall Mount ZV830 Installation Heights PossibleCheck Installation Hardware Locate and count Screws Duct cover28-7/8 ″ 10-7/8 ″INSTALLATION-VENTED to the Outside DUCTWORK, Wiring LocationsInstall Framing for Hood Support House Wiring LocationInstall Hood Mounting Screws Install Duct BracketMount the Hood Secure the bracket to the wallConnect Ductwork Verify that power is turned off at the source Install Duct CoversConnect Electrical Install Filters Finalize InstallationTape the template in position along the penciled line INSTALLATION-RECIRCULATINGImportant Framing must be capable of supporting 100 lbs Check to be sure the mounting screws are horizontally level Outlet Hold the assembly against Duct bracket Size and CUT Duct PieceSecure the junction box cover with the 6 original screws Remove protective plasticCovering Place the decorative duct Covers on top of the hoodRemove all tape and packing material Installation Instructions Installation Instructions Lisez ET Conservez CES Instructions Avant DE Commencer AvertissementAvertissement Pour Réduire Avertissement Afin DE RéduireDimensions ET Intervalles Options D’INSTALLATIONTable DES Matières 28 cm 10-7/8 poPlanification Accessoire Cache ConduitAlimentation Raccords DE Canalisation ’utilisez PAS de conduit en plastique flexibleOutils ET Matériaux Nécessaires Retirer L’EMBALLAGENON Fournis Serre-filsDéfinition DE LA Hauteur ’INSTALLATION AccessoiresSupport mural ZV830 Hauteurs d’installation HauteurVérification DU Matériel D’INSTALLATION Repérez et comptez les visINSTALLATION-VENTILÉ Vers L’EXTÉRIEUR Emplacement DES Câbles DE LA MaisonConduit de plafond Conduit muralInstaller LE Support DE Canalisation Installez Les vis Trou de ligne médianeMonter LA Hotte Fixez le support sur le murConnecter LA Canalisation Flux d’airVérifiez que l’alimentation est coupée à la source Cache de Boîte à bornesSupport de cache Conduit Trous de visInstaller LES Filtres Terminer L’INSTALLATIONINSTALLATION- Recyclage Monter LA Hotte Mesurer ET Couper LE Conduit Les sorties de la hotteLongueur Conduit Du déflecteurConnecter LES Parties Électriques CacheSupérieur Cache conduit Inférieur Vérifiez que l’alimentation est coupée à la sourceInstaller LES Filtres Instructions d’installation Instructions d’installation Instructions d’installation Guarde Estas Instrucciones Antes DE Empezar PrecauciónAdvertencia Tiempo para la instalación 1 a 3 horasContenidos Opciones DE Instalación10-7/8 Altura Hasta el 24 Mín 30 Máx 18-7/8 29-7/8Planificación Previa Fuente DE EnergíaAccesorio DE Cubierta DE Conducto Instrucciones de conexión a tierraDel ducto Dimensiones Equivalente Utilizada Total Accesorios Para ConductosLongitud Pieza Longitud CantidadQuite EL Envoltorio Herramientas Y Materiales RequeridosNo Incluido Establezca LA Altura DE Instalación AccesoriosAlturas de instalación De montaje de pared de ZV830 Altura deControle LOS Elementos Para LA Instalación INSTALACIÓN-VENTILACIÓN Hacia EL Exterior Ubicación DE LOS Conductos Y CableadoInstale EL Armazón Para EL Soporte DE LA Campana Ubicación DE Cableado DomésticoInstale LA Campana Instale LOS Tornillos DE Montaje DE LA CampanaQuite la plantilla Instale EL Soporte DEL ConductoConecte EL Conducto Instale LAS Cubiertas DE LOS Conductos Finalice LA Instalación Instale LOS FiltrosOrificios para Tornillos INSTALACIÓN-RECIRCULACIÓN Ubicación delCableado Doméstico El cielorrasoPencil Line Indicating Longitud De medidaOrificios de ventilación serán visibles en esta instalación Quite la tapa protectora de PlásticoCubierta de conducto i nferior Instale LOS Filtros Notas Notas GE Consumer & Industrial Para servicio técnico local Monogram en su área, llame al
Related manuals
Manual 40 pages 46.91 Kb

ZV830 specifications

The GE ZV830 is a groundbreaking and sophisticated addition to the lineup of kitchen appliances, designed to elevate both functionality and aesthetics. Packed with a range of advanced features, the ZV830 stands out as a state-of-the-art microwave that not only meets but exceeds modern culinary demands.

One of the standout characteristics of the GE ZV830 is its sleek and modern design, which seamlessly integrates into any kitchen decor. The appliance features a stainless-steel finish that is not only visually appealing but also easy to clean, making it a practical choice for busy homeowners. The unit is designed for installation over a range or cooktop, freeing up counter space while providing powerful cooking capabilities.

The ZV830 is equipped with a robust 1.7 cubic feet capacity, providing ample space for cooking large dishes or multiple items simultaneously. This microwave offers an impressive 1,000 watts of cooking power, ensuring quick and efficient heating, defrosting, and cooking of food.

One of the key technologies implemented in the GE ZV830 is its sensor cooking feature. This advanced technology allows the microwave to automatically adjust cooking times and power levels based on the moisture released from the food. As a result, users can achieve perfectly cooked meals without the guesswork traditionally associated with microwave cooking.

Additionally, the GE ZV830 boasts a range of convenient cooking presets and auto-reheat options, streamlining meal preparation. Features such as popcorn settings and pizza reheating options make it a versatile tool for any kitchen. The unit also includes a dedicated steam function, which is perfect for health-conscious individuals looking to prepare steamed vegetables easily.

Highly regarded for its user-friendly interface, the GE ZV830 includes a large LED display that provides clear visibility of cooking settings and times. The straightforward keypad allows for easy input, making it accessible for all users, including those less familiar with kitchen technology.

Furthermore, the GE ZV830 is designed with safety in mind. It includes child lock features to prevent unintended use, offering peace of mind for families. In conclusion, the GE ZV830 is an exemplary microwave that combines design, performance, and innovative technology to enhance the cooking experience. Its advanced features and user-centric design make it a valuable addition to any modern kitchen.
Top Page Image Contents