Fisher & Paykel OR36SDBGX Electrical Grounding Instructions, Replacement Parts

Page 5

GENERAL INFORMATION

1.Installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-Latest Edition.

2.Installation in manufactured (mobile) home: installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)] or, when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.

3.Installation in Recreational Park Trailers: installation must conform with state or other codes or, in the absence of such codes, with the Standard for Recreational Park Trailers, ANSI A119.5.

4. WARNING!!

This appliance shall not be used for space heating. This information is based on safety considerations.

5.AlI openings in the wall behind the appliance and in the floor under the appliance shall be sealed.

6.Keep appliance area clear and free from combustible materials, gasoline, and other flammable vapors.

7.Do not obstruct the flow of combustion and ventilation air.

8.Disconnect the electrical supply to the appliance before servicing.

9.When removing appliance for cleaning and/or service;

A.Shut off gas at main supply.

B.Disconnect AC power supply.

C.Disconnect gas line to the inlet pipe.

D.Carefully remove the range by pulling outward. CAUTION: Range is heavy; use care in handling.

10.Electrical Requirement

Electrical installation should comply with national and local codes.

11.Air Supply and Ventilation

The installer must refers to local/national codes.

12.Gas Manifold Pressure

Natural gas - 4.0” W.C.P. LP/Propane - 11.0” W.C.P.

WARNING!!

ELECTRICAL GROUNDING INSTRUCTIONS

The range must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70-latest edition. Installation should be made by a Iicensed electrician.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

If an external electrical source is utilized, the installation must be electrically grounded in accordance with local codes or, in the absence of local codes, with the national Electrical Code, ANSI/NFPA 70.

This appliance is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded socket.

Do not under any circumstances cut or remove the third (ground) prong from the power plug.

REPLACEMENT PARTS

Only authorized replacement parts may be used in performing service on the range. Replacement parts are available from factory authorized parts distributors. Contact the nearest parts distributor in your area.

13.The misuse of oven door (e.g. stepping, sitting, or leaning on them) can result in potential hazards and/or injuries.

14.When installing or removing the range for service, a rolling lift jack should be used. Do not push against any of the edges of the range in an attempt to slide it into or out of the installation. Pushing or pulling a range (rather than using a lift jack) also increases the possibility of bending the leg spindles or the internal coupling connectors.

5

Image 5
Contents Installation instructions Instructions dinstallation ALL Ranges can TIP For Installer only Installation Instructions Electrical Grounding Instructions Replacement PartsProximity to Side Cabinets A1installationGAS and Electric Connection 500 500 Moving the Cooker Fitting the Adjustable FeetLevelling the Cooker Assembling the Backguard It is mandatory to installOr the Island Trim Backguard or the island trim455 ANTI-TIP Stability Device Installation InstructionsPressure Regulator Manual Shut-off Valve figPressure Regulator Installation Step Step Step Connector GAS Connection SpecificationRigid Pipe Connections Leak TestingFlexible Connections Conversion to LP/PROPANE GAS Setting the Pressure Regulator figInjectors Table Operations to be Performed When Substituting InjectorsRapid and triple ring burners Setting the Burner Minimum Valves may varyOven Burner Adjustment of the Oven Burner Minimum Recommended ground method Electrical connectionWiring Diagram Avertissement ’INTENTION DE L’INSTALLATEUR Seulement Instructions D’INSTALLATION Pièces DE Rechange Instructions DE Mise À LA TerreProximité DES Armoires Raccordements Électrique ET AU GAZ 0po Min Déplacement DE LA Cuisinière Installation DES Pieds RéglablesGarniture d’îlot est recommandée ’installation du dosseret ou de laMontage DU Dosseret OU DE LA Garniture D’ÎLOT455,5 26- 11/16 po 678 mm Régulateur de pression Robinet d’arrêt manuel figInstallation DU Régulateur DE Pression Étape Étape Étape Spécification DU Raccordement AU GAZ Vérification de l’absence de fuite Raccords flexiblesRaccords de tuyaux rigides Réglage DU Régulateur DE Pression fig Conversion AU GAZ PROPANE/GPLBrûleurs Tableau DES InjecteursLes robinets peuvent varier Réglage Minimum DU BrûleurBrûleur du four Réglage Minimum DU Brûleur DU Four Raccordement électrique Méthode de mise à la terre recommandéeSchéma DE Câblage Page Page US CA